Chat now with support
Chat with Support

NetVault 13.0.2 - Administration Guide for Managed Service Providers

Introduction Getting started Configuring clients Managing catalog search Configuring storage devices
About storage devices SAN considerations Quest DR Series systems Quest QoreStor NetVault SmartDisk EMC Data Domain Systems Snapshot Array Manager Virtual Tape Libraries Virtual standalone drives Shared Virtual Tape Libraries Physical tape devices Storage tiers
Backing up data Managing policies Restoring data Managing NetVault dashboard Managing jobs Monitoring logs Managing storage devices
Role-based access to manage storage devices Monitoring device activity Managing disk-based storage devices in list view Managing disk-based storage devices in tree view Managing the Snapshot Array Manager Managing tape libraries in list view Managing tape libraries in tree view Managing tape drives in list view Managing tape drives in tree view Adding shared devices
Managing storage media Managing user and group accounts Managing Tenant Monitoring events and configuring notifications Reporting in NetVault Working with client clusters Configuring default settings for NetVault
About configuring default settings Configuring encryption settings Configuring plug-in options Configuring default settings for post-scripts Configuring default settings for Verify Plug-in Configuring Deployment Manager Settings Configuring Job Manager settings Configuring Logging Daemon settings Configuring Media Manager settings Configuring Network Manager settings Configuring Process Manager settings Configuring RAS device settings Configuring Schedule Manager settings Configuring Web Service settings Configuring Auditor Daemon settings Configuring firewall settings Configuring general settings Configuring security settings Synchronizing NetVault Time Configuring the reporting utility Configuring NetVault WebUI default settings Configuring NetVault to use a specific VSS provider Configuring default settings using Txtconfig
Diagnostic tracing Managing diagnostic data Using the deviceconfig utility NetVault processes Environment variables Network ports used by NetVault Troubleshooting
Common errors Safe Mode in NetVault

Configuring default settings for post-scripts

Configuring default settings for post‑scripts

By default, the execution of a post-script is terminated when a backup or restore job is aborted. You can modify the configuration setting for post-scripts to change this behavior.

To change the default setting for post-scripts:
1
In the Navigation pane, click Change Settings.
2
On the NetVault Server Settings page, complete one of the following actions:
•
To configure default settings for the NetVault Server, go to Step 3.
•
To configure default settings for a NetVault Client, click Clients. In the NetVault Clients table, select the client, and click Next.
3
Under Plugins, click Script.
4
In the Script dialog box, configure the following setting:
•
Terminate running script on Job Abort: This check box is selected by default. If you want to continue script execution even when the associated job is aborted, clear this check box.
This setting applies to all post-scripts defined for the backup, restore, and report jobs performed on the given NetVault Client.
5
Click Apply to apply the new settings and close the dialog box.

Configuring default settings for Verify Plug-in

Configuring default settings for Verify Plug‑in

With a backup job, you can choose to run the verification phase to check the correctness and completeness of a backup at the end of data transfer. NetVault uses the built-in Verify plug-in to perform the verification phase. The Verify plug-in verifies the stream length written to the media and ensures that no blocks were dropped during backup. While the actual backup runs as Phase 1, backup verification runs as Phase 2 of the backup job.

By default, the backup verification job runs on the NetVault Server. You can modify the configuration settings for the plug-in to run the verification on an alternate client or locally on specified clients.

To configure default settings for the Verify Plug-in:
1
In the Navigation pane, click Change Settings.
2
On the NetVault Server Settings page, under Plugins, click Verify. In the Verify dialog box, configure the following settings.
 
Table 131. Default settings for Verify plug-in
Setting
Description

Always run Verify locally

By default, the verification phase runs on the NetVault Server.

To avoid data transfers over the network, you can choose to run verification locally on the clients to which the device used for backup is attached. This option is globally applied to all clients. It does not work for clients that do not have a locally attached backup device.

Comma separated list of clients that verify locally

If your backup jobs are distributed across multiple client-attached devices, use this setting to specify a comma-separated list of clients that can run the verification phase locally.

Default client to run Verify

To configure an alternate client to run all verification jobs, specify the client name.

This setting is useful if you use a client-attached device for your backups. It allows you to select the same client to run backup verification jobs.

 
* 
NOTE: You must configure these settings on the NetVault Server.
3
Click Apply to apply the new settings and close the dialog box.

Configuring Deployment Manager Settings

This section includes the following topics:

•
About Deployment Manager
•
Configuring default settings for Deployment Manager

About Deployment Manager

The Deployment Manager process (nvdeploymentmgr) runs on the NetVault Server. This process manages the push installation tasks.

You can use the push installation method to perform the following tasks:

•
Install and upgrade the NetVault Client software simultaneously on multiple machines
•
Install and upgrade NetVault plug-ins simultaneously on multiple machines
•
Add new clients to the NetVault Server

For more information about the push installation method, see Installing software from WebUI (push installation).

You can modify the Deployment Manager settings from the Change Settings page.

Related Documents

The document was helpful.

Select Rating

I easily found the information I needed.

Select Rating