Converse agora com nosso suporte
Chat com o suporte

DR Series DR4300 - Owner's Manual

DR4300 system overview Technical specifications Initial system setup and configuration Pre-operating system management applications
Options to manage the pre-operating system applications System Setup Dell Lifecycle Controller Boot Manager PXE boot
Installing and removing system components
Safety instructions Before working inside your system After working inside your system Recommended tools Front bezel (optional) System cover Cooling shroud Cooling fans Cooling-fan assembly System memory Processors and heat sinks PCIe card holder Cable retention bracket Integrated storage controller card Expansion cards and expansion card riser Internal dual SD module (optional) Network daughter card Internal USB memory key (optional) System battery Power supply units (PSU) System board Trusted Platform Module Hard drives Hard drive backplane SD vFlash card (optional) Control panel assembly
Using system diagnostics Jumpers and connectors Troubleshooting your system

Serial Communication details

Serial Communication
Viewing Serial Communication
Serial Communication details

You can use the Serial Communication screen to view the properties of the serial communication port.

Related tasks 
Serial Communication details
Viewing Serial Communication
Related references 
System BIOS
Viewing Serial Communication

To view the Serial Communication screen, perform the following steps:

1.
Turn on, or restart your system.
2.
Press F2 immediately after you see the following message:
F2 = System Setup
* 
NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then restart your system and try again.
3.
On the System Setup Main Menu screen, click System BIOS.
4.
On the System BIOS screen, click Serial Communication.
Related tasks 
Serial Communication details
Related references 
Serial Communication

The Serial Communication screen details are explained as follows:

Option
Description
Serial Communication
Selects serial communication devices (Serial Device 1 and Serial Device 2) in BIOS. BIOS console redirection can also be enabled and the port address can be specified. This option is set to Auto by default.
Serial Port Address
Enables you to set the port address for serial devices. This option is set to Serial Device 1=COM2, Serial Device 2=COM1 by default.
* 
NOTE: You can use only Serial Device 2 for the Serial Over LAN (SOL) feature. To use console redirection by SOL, configure the same port address for console redirection and the serial device.
* 
NOTE: Every time the system boots, the BIOS syncs the serial MUX setting saved in iDRAC. The serial MUX setting can independently be changed in iDRAC. Loading the BIOS default settings from within the BIOS setup utility may not always revert the serial MUX setting to the default setting of Serial Device 1.
External Serial Connector
Enables you to associate the External Serial Connector to Serial Device 1, Serial Device 2, or the Remote Access Device by using this option.
* 
NOTE: Only Serial Device 2 can be used for Serial Over LAN (SOL). To use console redirection by SOL, configure the same port address for console redirection and the serial device.
* 
NOTE: Every time the system boots, the BIOS syncs the serial MUX setting saved in iDRAC. The serial MUX setting can independently be changed in iDRAC. Loading the BIOS default settings from within the BIOS setup utility may not always revert this setting to the default setting of Serial Device 1.
Failsafe Baud Rate
Specifies the failsafe baud rate for console redirection. The BIOS attempts to determine the baud rate automatically. This failsafe baud rate is used only if the attempt fails, and the value must not be changed. This option is set to 115200 by default.
Remote Terminal Type
Sets the remote console terminal type. This option is set to VT 100/VT 220 by default.
Redirection After Boot
Enables or disables the BIOS console redirection when the operating system is loaded. This option is set to Enabled by default.
Related tasks 
Viewing Serial Communication
Related references 
Serial Communication

System Profile Settings

Viewing System Profile Settings
System Profile Settings details

You can use the System Profile Settings screen to enable specific system performance settings such as power management.

Related tasks 
System Profile Settings details
Viewing System Profile Settings
Related references 
System BIOS
Viewing System Profile Settings

To view the System Profile Settings screen, perform the following steps:

1.
Turn on, or restart your system.
2.
Press F2 immediately after you see the following message:
F2 = System Setup
* 
NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then restart your system and try again.
3.
On the System Setup Main Menu screen, click System BIOS.
4.
On the System BIOS screen, click System Profile Settings.
Related tasks 
System Profile Settings details
Related references 
System Profile Settings
System Profile Settings details

The System Profile Settings screen details are explained as follows:

Option
Description
System Profile
Sets the system profile. If you set the System Profile option to a mode other than Custom, the BIOS automatically sets the rest of the options. You can only change the rest of the options if the mode is set to Custom. This option is set to Performance Per Watt Optimized (DAPC) by default. DAPC is Dell Active Power Controller.
* 
NOTE: All the parameters on the system profile setting screen are available only when the System Profile option is set to Custom.
CPU Power Management
Sets the CPU power management. This option is set to System DBPM (DAPC) by default. DBPM is Demand-Based Power Management.
Memory Frequency
Sets the speed of the system memory. You can select Maximum Performance, Maximum Reliability, or a specific speed.
Turbo Boost
Enables or disables the processor to operate in the turbo boost mode. This option is set to Enabled by default.
Energy Efficient Turbo
Enables or disables the Energy Efficient Turbo option.
Energy Efficient Turbo (EET) is a mode of operation where a processor’s core frequency is adjusted to be within the turbo range based on workload.
C1E
Enables or disables the processor to switch to a minimum performance state when it is idle. This option is set to Enabled by default.
C States
Enables or disables the processor to operate in all available power states. This option is set to Enabled by default.
Collaborative CPU Performance Control
Enables or disables the CPU power management option. When set to Enabled, the CPU power management is controlled by the OS DBPM and the System DBPM (DAPC). This option is set to Disabled by default.
Memory Patrol Scrub
Sets the memory patrol scrub frequency. This option is set to Standard by default.
Memory Refresh Rate
Sets the memory refresh rate to either 1x or 2x. This option is set to 1x by default.
Uncore Frequency
Enables you to select the Processor Uncore Frequency option.
Dynamic mode enables the processor to optimize power resources across the cores and uncore during runtime. The optimization of the uncore frequency to either save power or optimize performance is influenced by the setting of the Energy Efficiency Policy option.
Energy Efficient Policy
Enables you to select the Energy Efficient Policy option.
The CPU uses the setting to manipulate the internal behavior of the processor and determines whether to target higher performance or better power savings.
Number of Turbo Boot Enabled Cores for Processor 1
* 
NOTE: If there are two processors installed in the system, you see an entry for Number of Turbo Boost Enabled Cores for Processor 2.
Controls the number of turbo boost enabled cores for processor 1. The maximum number of cores is enabled by default.
Monitor/Mwait
Enables the Monitor/Mwait instructions in the processor. This option is set to Enabled for all system profiles, except Custom by default.
* 
NOTE: This option can be disabled only if the C States option in the Custom mode is set to disabled.
* 
NOTE: When C States is set to Enabled in the Custom mode, changing the Monitor/Mwait setting does not impact the system power or performance.
Related tasks 
Viewing System Profile Settings
Related references 
System Profile Settings

Viewing System Profile Settings

System Profile Settings
Viewing System Profile Settings
System Profile Settings details

You can use the System Profile Settings screen to enable specific system performance settings such as power management.

Related tasks 
System Profile Settings details
Viewing System Profile Settings
Related references 
System BIOS

To view the System Profile Settings screen, perform the following steps:

1.
Turn on, or restart your system.
2.
Press F2 immediately after you see the following message:
F2 = System Setup
* 
NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then restart your system and try again.
3.
On the System Setup Main Menu screen, click System BIOS.
4.
On the System BIOS screen, click System Profile Settings.
Related tasks 
System Profile Settings details
Related references 
System Profile Settings
System Profile Settings details

The System Profile Settings screen details are explained as follows:

Option
Description
System Profile
Sets the system profile. If you set the System Profile option to a mode other than Custom, the BIOS automatically sets the rest of the options. You can only change the rest of the options if the mode is set to Custom. This option is set to Performance Per Watt Optimized (DAPC) by default. DAPC is Dell Active Power Controller.
* 
NOTE: All the parameters on the system profile setting screen are available only when the System Profile option is set to Custom.
CPU Power Management
Sets the CPU power management. This option is set to System DBPM (DAPC) by default. DBPM is Demand-Based Power Management.
Memory Frequency
Sets the speed of the system memory. You can select Maximum Performance, Maximum Reliability, or a specific speed.
Turbo Boost
Enables or disables the processor to operate in the turbo boost mode. This option is set to Enabled by default.
Energy Efficient Turbo
Enables or disables the Energy Efficient Turbo option.
Energy Efficient Turbo (EET) is a mode of operation where a processor’s core frequency is adjusted to be within the turbo range based on workload.
C1E
Enables or disables the processor to switch to a minimum performance state when it is idle. This option is set to Enabled by default.
C States
Enables or disables the processor to operate in all available power states. This option is set to Enabled by default.
Collaborative CPU Performance Control
Enables or disables the CPU power management option. When set to Enabled, the CPU power management is controlled by the OS DBPM and the System DBPM (DAPC). This option is set to Disabled by default.
Memory Patrol Scrub
Sets the memory patrol scrub frequency. This option is set to Standard by default.
Memory Refresh Rate
Sets the memory refresh rate to either 1x or 2x. This option is set to 1x by default.
Uncore Frequency
Enables you to select the Processor Uncore Frequency option.
Dynamic mode enables the processor to optimize power resources across the cores and uncore during runtime. The optimization of the uncore frequency to either save power or optimize performance is influenced by the setting of the Energy Efficiency Policy option.
Energy Efficient Policy
Enables you to select the Energy Efficient Policy option.
The CPU uses the setting to manipulate the internal behavior of the processor and determines whether to target higher performance or better power savings.
Number of Turbo Boot Enabled Cores for Processor 1
* 
NOTE: If there are two processors installed in the system, you see an entry for Number of Turbo Boost Enabled Cores for Processor 2.
Controls the number of turbo boost enabled cores for processor 1. The maximum number of cores is enabled by default.
Monitor/Mwait
Enables the Monitor/Mwait instructions in the processor. This option is set to Enabled for all system profiles, except Custom by default.
* 
NOTE: This option can be disabled only if the C States option in the Custom mode is set to disabled.
* 
NOTE: When C States is set to Enabled in the Custom mode, changing the Monitor/Mwait setting does not impact the system power or performance.
Related tasks 
Viewing System Profile Settings
Related references 
System Profile Settings

System Profile Settings details

System Profile Settings
Viewing System Profile Settings
System Profile Settings details

You can use the System Profile Settings screen to enable specific system performance settings such as power management.

Related tasks 
System Profile Settings details
Viewing System Profile Settings
Related references 
System BIOS
Viewing System Profile Settings

To view the System Profile Settings screen, perform the following steps:

1.
Turn on, or restart your system.
2.
Press F2 immediately after you see the following message:
F2 = System Setup
* 
NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then restart your system and try again.
3.
On the System Setup Main Menu screen, click System BIOS.
4.
On the System BIOS screen, click System Profile Settings.
Related tasks 
System Profile Settings details
Related references 
System Profile Settings

The System Profile Settings screen details are explained as follows:

Option
Description
System Profile
Sets the system profile. If you set the System Profile option to a mode other than Custom, the BIOS automatically sets the rest of the options. You can only change the rest of the options if the mode is set to Custom. This option is set to Performance Per Watt Optimized (DAPC) by default. DAPC is Dell Active Power Controller.
* 
NOTE: All the parameters on the system profile setting screen are available only when the System Profile option is set to Custom.
CPU Power Management
Sets the CPU power management. This option is set to System DBPM (DAPC) by default. DBPM is Demand-Based Power Management.
Memory Frequency
Sets the speed of the system memory. You can select Maximum Performance, Maximum Reliability, or a specific speed.
Turbo Boost
Enables or disables the processor to operate in the turbo boost mode. This option is set to Enabled by default.
Energy Efficient Turbo
Enables or disables the Energy Efficient Turbo option.
Energy Efficient Turbo (EET) is a mode of operation where a processor’s core frequency is adjusted to be within the turbo range based on workload.
C1E
Enables or disables the processor to switch to a minimum performance state when it is idle. This option is set to Enabled by default.
C States
Enables or disables the processor to operate in all available power states. This option is set to Enabled by default.
Collaborative CPU Performance Control
Enables or disables the CPU power management option. When set to Enabled, the CPU power management is controlled by the OS DBPM and the System DBPM (DAPC). This option is set to Disabled by default.
Memory Patrol Scrub
Sets the memory patrol scrub frequency. This option is set to Standard by default.
Memory Refresh Rate
Sets the memory refresh rate to either 1x or 2x. This option is set to 1x by default.
Uncore Frequency
Enables you to select the Processor Uncore Frequency option.
Dynamic mode enables the processor to optimize power resources across the cores and uncore during runtime. The optimization of the uncore frequency to either save power or optimize performance is influenced by the setting of the Energy Efficiency Policy option.
Energy Efficient Policy
Enables you to select the Energy Efficient Policy option.
The CPU uses the setting to manipulate the internal behavior of the processor and determines whether to target higher performance or better power savings.
Number of Turbo Boot Enabled Cores for Processor 1
* 
NOTE: If there are two processors installed in the system, you see an entry for Number of Turbo Boost Enabled Cores for Processor 2.
Controls the number of turbo boost enabled cores for processor 1. The maximum number of cores is enabled by default.
Monitor/Mwait
Enables the Monitor/Mwait instructions in the processor. This option is set to Enabled for all system profiles, except Custom by default.
* 
NOTE: This option can be disabled only if the C States option in the Custom mode is set to disabled.
* 
NOTE: When C States is set to Enabled in the Custom mode, changing the Monitor/Mwait setting does not impact the system power or performance.
Related tasks 
Viewing System Profile Settings
Related references 
System Profile Settings
Documentos relacionados

The document was helpful.

Selecione a classificação

I easily found the information I needed.

Selecione a classificação