These parameters are used by the SharePlex Export process.
SP_XPT_AES_KEY_LENGTH
This parameter controls the size of the AES encryption key that is used by Export to encrypt data that is sent across the network from source to target. The key itself is generated by issuing the create encryption key command, which generates a full 256-bit key. The SP_XPT_AES_KEY_LENGTH parameter controls how much of that length is used as the key when Export encrypts the data. The default is 128 bits, the minimum length. A longer key is harder to hack but requires more CPU power. To configure SharePlex for AES encryption, see the SharePlex Administration Guide.
Default: 128-bits
Range of valid values: 128, 192 or 256 bits
Takes effect: when Export is restarted
SP_XPT_ENABLE_AES
This parameter controls whether Advanced Encryption Standard (AES) is enabled to encrypt replicated data that is sent by Export across the network. To configure SharePlex for AES encryption, see the SharePlex Administration Guide.
Default: 0 (disabled)
Range of valid values: 0 or 1 (enabled)
Takes effect: when Export is restarted
SP_XPT_ENABLE_COMPRESSION
This parameter controls the compression of data across TCP/IP.
You can enable compression to reduce the amount of data that SharePlex sends across the network. SharePlex uses LZIP lossless compression. Enabling compression on the source SharePlex instance automatically enables compression to all targets of the source SharePlex instance.
By default compression is disabled. You can enable compression by itself or in conjunction with encryption. For more information about encryption, see the SharePlex Administration Guide.
Default: 0 (disabled)
Range of valid values: 0 or 1 (enabled)
Takes effect: when Export is restarted
SP_XPT_KEEPALIVE
This parameter controls whether the Export process sends a "hello" message to Import at regular intervals to prevent TCP timeouts when replication activity is low. If the network times out because no replication packets are being sent, SharePlex alerts you with a message such as "Export cannot connect to import on server2: timeout waiting for ack." By setting SP_XPT_KEEPALIVE to 1, you can eliminate this message and keep the SharePlex network connection alive.
Default: 0 (disabled)
Range of valid values: 0 or 1 (enabled)
Takes effect: when Export is restarted
SP_XPT_PORT_OVERRIDE
This parameter works in conjunction with the SP_XPT_USE_LOCALHOST parameter to enable SharePlex to send data through a secure tunnel port created with SSH® Secure ShellTM software. This parameter sets the local connection, which overrides the default SharePlex port. From that port number, the SSH daemon directs the connection to a different system (the SharePlex target machine) using another port number and the SSH data encryption.
Default: 0 (disabled)
Range of valid values: 0 or any positive integer
Takes effect: when Export is restarted
SP_XPT_SO_SNDBUF
This parameter tunes the TCP/IP window size on the source machine. It works in conjunction with the SP_COP_SO_RCVBUF parameter on the target machine to establish the size of a packet sent across the network. SharePlex references both parameters when TCP/IP sockets are created at the startup of sp_cop and the Export process.
If SharePlex is replicating across a WAN and the export queue is continually backlogged, try adjusting both parameters. SP_XPT_SO_SNDBUF must be set equal to or greater than the value of SP_COP_SO_RCVBUF, in multiples of 1024 bytes. To size the parameters, determine the ping time between the source and target machines, then use the following formula for both parameters:
param_value / ping_time= bytes per second
For example, if ping time is 200 milliseconds, and the value for the two parameters is 64K, SharePlex will send five 64K-packets every second, totaling 320K per second.
Unless you observe a bandwidth problem, Quest recommends leaving both parameters set to their defaults, which use the system's setting. To change SP_XPT_SO_SNDBUF, set it on the source system, then stop and start Export on that system.
If transfer still is slow, try increasing the SP_IMP_WCMT_MSGCNT and SP_IMP_WCMT_TIMEOUT parameters on the target system. Set SP_IMP_WCMT_MSGCNT to at least 10,000.
Default: 0 (default is set by the operating system)
Range of valid values: positive integers, in bytes, using multiples of 1024. Maximum is set by the operating system.
Takes effect: when Export is restarted
SP_XPT_USE_LOCALHOST
This parameter enables SharePlex to send data through a secure tunnel port created with SSH® Secure ShellTM software. The Export process reads this parameter before making a TCP connection. If the parameter is enabled, the Export process connects to the local host through a local port number, where the SSH daemon directs the connection to a different system (the SharePlex target machine) using another port number and the SSH data encryption.
Default: 0 (disabled)
Range of valid values: 0 or 1 (flag)
Takes effect: when Export is restarted