Tchater maintenant avec le support
Tchattez avec un ingénieur du support

NetVault 13.0.2 - Administration Guide for Managed Service Providers

Introduction Getting started Configuring clients Managing catalog search Configuring storage devices
About storage devices SAN considerations Quest DR Series systems Quest QoreStor NetVault SmartDisk EMC Data Domain Systems Snapshot Array Manager Virtual Tape Libraries Virtual standalone drives Shared Virtual Tape Libraries Physical tape devices Storage tiers
Backing up data Managing policies Restoring data Managing NetVault dashboard Managing jobs Monitoring logs Managing storage devices
Role-based access to manage storage devices Monitoring device activity Managing disk-based storage devices in list view Managing disk-based storage devices in tree view Managing the Snapshot Array Manager Managing tape libraries in list view Managing tape libraries in tree view Managing tape drives in list view Managing tape drives in tree view Adding shared devices
Managing storage media Managing user and group accounts Managing Tenant Monitoring events and configuring notifications Reporting in NetVault Working with client clusters Configuring default settings for NetVault
About configuring default settings Configuring encryption settings Configuring plug-in options Configuring default settings for post-scripts Configuring default settings for Verify Plug-in Configuring Deployment Manager Settings Configuring Job Manager settings Configuring Logging Daemon settings Configuring Media Manager settings Configuring Network Manager settings Configuring Process Manager settings Configuring RAS device settings Configuring Schedule Manager settings Configuring Web Service settings Configuring Auditor Daemon settings Configuring firewall settings Configuring general settings Configuring security settings Synchronizing NetVault Time Configuring the reporting utility Configuring NetVault WebUI default settings Configuring NetVault to use a specific VSS provider Configuring default settings using Txtconfig
Diagnostic tracing Managing diagnostic data Using the deviceconfig utility NetVault processes Environment variables Network ports used by NetVault Troubleshooting
Common errors Safe Mode in NetVault

Configuring default settings for Schedule Manager

To configure default settings for Schedule Manager:
1
In the Navigation pane, click Change Settings.
2
On the NetVault Server Settings page, under Services, click Schedule Manager. In the Schedule Manager dialog box, configure the following settings.
 
Table 145. Schedule Manager settings
Setting
Description

Number of days to keep job status

This setting determines display period for job status records.

The default setting is seven days. To change the display period, type or select a new value. The display period is specified in number of days.

NOTE: This setting just hides the display of job status records on the NetVault WebUI. It does not delete the records from the Scheduler Database.

Number of days to keep report job histories in the database

This setting determines the retention period for report job history.

The default setting is 90 days. To change the retention period, type or select a new value. The retention period is specified in number of days. After the retention period expires, these records are removed from the Scheduler Database.

Number of days to keep other job histories in the database

This setting determines the retention period for backup and restore job history.

The default setting is 90 days. To change the retention period, type or select a new value. The retention period is specified in number of days. After the retention period expires, these records are removed from the Scheduler Database.

Number of days to keep non-scheduled jobs in the database

This setting determines the retention period for non-repeating jobs.

The default value for this setting is 0 (zero). With the default setting, the job definitions of non-repeating jobs are retained indefinitely. To delete these jobs after a specified period, type or select a new value. The retention period is specified in number of days.

NOTE: Because the jobs using the Triggered schedule type have no physical scheduled time, they are also deleted after the specified period elapses. If you are using Triggered jobs in your NetVault environment, do not use this setting.
NOTE: This setting is also applied to report jobs that use any non-repeating schedule type. Therefore, we recommend that you do not change the default value for this setting. If the default value is changed, canned reports that have run once using any non-repeating schedule are removed from the View Reports page after the specified interval.

Maximum simultaneously active jobs

This setting determines the maximum number of simultaneous jobs that you can run in NetVault.

By default, the Schedule Manager supports a maximum of 200 simultaneous jobs, including backup, restore and report jobs. To change the setting, type or select a new value.

NOTE: Each active job requires some amount of shared memory. An increase in the number of active jobs might have an impact on the overall performance of NetVault.

Exclude reports jobs from jobs management views

To display report jobs on the Job Status page, clear this check box.

These jobs are excluded by default.

Exclude reports jobs from policy management views

To display report jobs on the Manage Policy page, clear this check box.

These jobs are excluded by default.

Exclude restore jobs from policy management views

To display restore jobs on the Manage Policy page, clear this check box.

These jobs are excluded by default.

3
Click Apply to apply the new settings and close the dialog box.

Configuring default job priority settings

The Schedule Manager assigns a default priority level to each job type (backup, restore, and report). These default settings are applied globally to all backup, restore, and report jobs. The priority settings are used to prioritize resource allocation when two or more jobs are scheduled to run at the same time. You can change the default job priority settings from the Change Settings page.

By default, the Schedule Manager assigns the following priority levels:

•
Backup job: 30
•
Restore job: 20
•
Report job: 50

To change the priority settings globally for all jobs, use the following procedure. You can override the priority setting for an individual job by configuring the Job Priority option in the Schedule Set. For more information, see Creating Schedule Sets, Table 40.

To configure default job priority settings:
1
In the Navigation pane, click Change Settings.
2
On the NetVault Server Settings page, under Services, click Schedule Manager. In the Schedule Manager dialog box, configure the following settings:
•
Default backup job priority
•
Default restore job priority
•
Default report job priority
Type or select a value from 1 through 100. 1 denotes highest priority, while 100 denotes lowest priority. A job with a priority level of zero (0) runs as a background task.
 
* 
NOTE: If you configured a Secondary Copy, the Secondary Copy job has two requests: one for read and another for write. When you set a priority to the Secondary Copy job, the first request (source request) receives the priority that the user assigns to it; the subsequent request (destination request) served as first priority in the background with priority 0 or 1. This implementation is to avoid waiting for the destination media request to be served if the source media is available.
 
3
Click Apply to apply the new settings and close the dialog box.

Configuring Web Service settings

This section includes the following topics:

•
Configuring Web Service to disable ciphers
•
Configuring Web Service to disable protocols
•
Enabling Web Service auditing
•
Configuring timeout period for client operations
•
Configuring timeout period for saveset removal request

Configuring Web Service to disable ciphers

You can modify the Web Service configuration to disable ciphers for incoming web service connections settings to prevent from allowing one or more ciphers. You can configure this setting from the Change Settings page.

To configure Web Service to disable ciphers:
1
In the Navigation pane, click Change Settings.
2
On the NetVault Server Settings page, under Services, click Web Service. In the Web Service dialog box, configure the following setting:
•
Ciphers to disable for incoming Web Service connections: To disable a cipher for incoming web service connections, enter its value given in the second column of the table as mentioned in the link https://www.openssl.org/docs/man1.0.2/apps/ciphers.html. However, if the entered cipher does not match with ciphers of incoming web service connection, no cipher is disabled. To disable multiple ciphers, enter the values separated by comma. By default, this field is blank and all the ciphers are allowed.
•
Click Apply to apply the new settings and close the dialog box.
Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation