Add an interface to an existing bond.
network --add_member --bondif <bondN>
--nwif <eth0, eth1, . . . ,ethN>
--bondif Bond interface to add to.
--nwif Eth interfaces to add.
For example, to add eth2 to bond1, run the command: network --add_member --bondif bond1 --nwif eth2
Interface add successful. Please restart networking for the changes to take effect.
Configures the domain name system (DNS) for a DR Series system, which includes the corresponding DNS suffix and a primary name server IP address (and optionally, a secondary name server IP address).
network --setdns --suffix storage.local --primary 10.25.20.21 --secondary 10.25.20.25
Configures or updates the bonding mode or sets the maximum transmission unit (MTU) number to use for a DR Series system.
network --bondif bond1 --setbonding --mode ALB --mtu 1750
Bond device operation successful. Please run 'network --restart' for the changes to take effect.
|
|
NOTE: ALB load balancing does not balance the load properly when the backup servers are on a remote subnet. This is because ALB uses the address resolution protocol (ARP) and ARP updates are subnet-specific. Because of this, ARP broadcasts and updates are not sent across the router. Instead, all traffic is sent to the first interface in the bond. To resolve this ARP-specific issue, make sure that the data source systems reside on the same subnet as the DR Series system. |
|
|
NOTE: When setting or changing the MTU value, make sure to verify that the Ethernet network switch is capable of supporting an MTU size that is equal to or larger than the value being set. Any mismatch in MTU values between the clients, the Ethernet network switch, and the DR Series system will make it inoperable. The relationship of jumbo frames to MTU is discussed in this topic. |
|
|
NOTE: When using the DR Series system CLI --setbonding and --mtu commands, a warning dialog displays with the following message: Incorrectly setting the MTU size will cause the DR4000 to not respond. You will need to log in to the system console and use the network --setbonding --bondif bond0 --mtu 1500 command to resolve the issue. Please verify that the switch is enabled and capable of supporting an MTU size that is equal to or larger than the value being set. Do you want to continue (yes/no) ? |
|
|
Caution: If the existing bonding setting is changed, the connection to the DR Series system may be lost unless you are sure that the DR Series system can accept this bonding type. |
In computer networking, jumbo frames are Ethernet frames with more than 1500 bytes of payload (but in some cases, jumbo frames can carry up to 9000 bytes of payload).
Many Gigabit Ethernet switches and Gigabit Ethernet network interface cards support jumbo frames. Some Fast Ethernet switches and Fast Ethernet network interface cards (NICs) also support jumbo frames.
Some computer manufacturers use 9000 bytes as the conventional limit for jumbo frame sizes. Internet Protocol (IP) subnetworks require that all hosts in a subnet have an identical MTU.
Consequently, interfaces that use a standard frame size and those that use a jumbo frame size should not be in the same subnet. To reduce the chance of interoperability issues, NICs capable of jumbo frames require special configurations to use jumbo frames. For more information, contact your Technical Support representative for assistance.
To verify that the destination system can support a specific frame size you want to attempt, use the following DR Series system CLI commands and specify the frame size in bytes using the following command as an example:
network --ping --destination <ip address> --size <number of bytes>
The command updates bonding and individual interface information.
network --update [--bondif <bondN>]
[--nwif <ethN>]
[--mode < ALB | 802.3ad>]
[--name < DNS name >]
[--mtu <Supported MTU range 512 - 9000>]
--bondif Bond interface to update.
--nwif Eth interface to update.
--mode Bonding mode to use.
--name DNS name for the interface.
--mtu Ethernet MTU to use (valid range is 512 - 9000).
For example, to update bond1 to use a different MTU parameter, run the command: network --update --bondif bond1 --mtu 5000
WARNING: Incorrectly setting the MTU size will cause the DR appliance to not respond. Please verify that the switch is enabled and capable of supporting an MTU size that is equal to or larger than the value being set. Do you want to continue (yes/no) [n]? y Interface update successful.
© 2024 Quest Software Inc. ALL RIGHTS RESERVED. Términos de uso Privacidad Cookie Preference Center