3. |
4. |
Enter the domain the appliance is on. For example, example.com. | |||
Select the speed of your network. This speed should match the setting of your LAN switch. If you select Auto-negotiate, the system determines the best value automatically provided that the LAN switch supports auto-negotiation. | |||
Enter the subnet (network segment) that the appliance is on. For example, 255.255.255.0. | |||
Enter the IP address of the primary DNS server the appliance uses to resolve host names. | |||
Optional: Enter the IP address of the secondary DNS server the appliance uses to resolve host names. | |||
Optional: Enter proxy server information. | |||
The Save appliance data setting enables you to save the appliance data to an offboard virtual disk during the initial configuration for a new Virtual appliance and a new Remote Site Appliance. You can also configure offboard storage later for the virtual KACE Systems Deployment Appliance and RSA using the Administrator Console. The Save appliance data setting is not available for the physical KACE Systems Deployment Appliance during the initial configuration. Configure the physical appliance to save the appliance data to an offboard-storage device from the Administrator Console. Select one of the following check boxes: |
6. |
You can modify the initial network settings configured from the appliance Network Setup Console.
1. |
On the left navigation pane, click Settings > Control Panel to display the Control Panel, then click Network Settings to display the Network Settings page. |
Enter the domain the appliance is on. For example, example.com. | |
Enter the IP address of the primary DNS server the appliance uses to resolve host names. | |
Optional: Enter the IP address of the secondary DNS server the appliance uses to resolve host names. | |
3. |
Select the speed of the interface. This speed should match the setting of your LAN switch. If you select Auto-negotiate, the system determines the best value automatically provided that the LAN switch supports auto-negotiation. | |
Enter the subnet (network segment) that the interface is on. For example, 255.255.255.0. | |
Read-only field. It indicates if the network cable is plugged into the interface. | |
Select this option if you want this interface to be used as a deployment interface. |
4. |
Under Available Link Aggregation Interfaces, configure or enable the available interfaces. Link aggregation allows you to combine multiple network interfaces to increase throughput beyond what a single connection can sustain, and to provide redundancy in case a link fails. You can aggregate up to eight network interfaces. |
5. |
6. |
7. |
8. |
The following passwords are associated with the appliance.
The default password is admin. The new password must be six characters or more in length. | |||||
Samba Share Password, KACE Media Manager, and KACE Boot Environment (KBE) |
The default password is admin and is used for uploading drivers and backing up and restoring library components, scripted installations, system images, boot environments, network inventory, and network scans. | ||||
Enables a connection to a target device that has networked booted. | |||||
If you change the Administrator's password, and become locked out of the appliance Administrator Console for some reason, you can re-set the password using the Command Line Console.
To change the Administrator's password, you must obtain last 16 characters of your appliance license key, including dashes, using the correct case, as specified. You can use the legacy KACE license key or the Quest license key. The Command Line Console is a terminal window to the appliance. Logging in to the Command Line Console as the netdiag user provides access to some basic network diagnostic commands, including reset_admin_password, that allows you to change the Administrator's password.
Your full license key is listed in the Welcome email from Quest KACE. It is also available on the Registration and Licensing page in the Administrator Console (when you have access to it). If you do not have a license key, contact Quest KACE Technical Support at https://support.quest.com/contact-support, or the licensing team to obtain a new key at https://support.quest.com/licensing-assistance. For more information about the Registration and Licensing page, see the help topic associated with this page.
TIP: You can access product documentation and additional resources associated with a specific page by clicking Need Help. For more information, see Access product documentation. |
2. |
Password: netdiag
4. |
a. |
b. |
In the KACE Systems Deployment Appliance Administrator Console login screen, type the following values: |
▪ |
Login ID: admin |
▪ |
Password: Type the six characters of your newly changed Administrator's password (not including the quotation marks). |
c. |
8. |
© 2024 Quest Software Inc. ALL RIGHTS RESERVED. Terms of Use Privacy Cookie Preference Center