Converse agora com nosso suporte
Chat com o suporte

NetVault Bare Metal Recovery 13.1.2 - User Guide for Plug-ins

Introducing NetVault Bare Metal Recovery Plug-ins Deploying NetVault Bare Metal Recovery Using the Plug-in Offline Client
Plug-in Server: an overview Installing and removing Plug-in Server Configuring Plug-in Server for use with Plug-in Offline Client Booting a NetVault Bare Metal Recovery Client with Plug-in Offline Client Backing up data with Plug-in Offline Client Restoring data with Plug-in Offline Client
Using NetVault Bare Metal Recovery Plug-in Live Client
Plug-in Live Client overview Configuring Plug-in Server for use with Plug-in Live Client Installing and removing Plug-in Live Client Backing up data with Plug-in Live Client Booting a NetVault Bare Metal Recovery Client with Plug-in Offline Client Restoring data with Plug-in Live Client
NetVault Bare Metal Recovery physical-to-virtual (P2V) recovery  Troubleshooting

Removing a NetVault Bare Metal Recovery Client

If you must remove an existing NetVault Bare Metal Recovery Client from the NetVault Server, perform the following steps:

1
In the Navigation pane, click Create Backup Job.
2
Next to the Selections list, click .
3
On the NetVault Selections page, double-click the NetVault Server — with the Plug-in Server installed on it — to open it.
4
Double-click the Plug-in Server, labeled “VaultDR APM.”
5
Click the applicable client, and select Remove Client from the context menu.
6
When the confirmation dialog box is displayed, click Yes.

Booting a NetVault Bare Metal Recovery Client with Plug-in Offline Client

Booting a NetVault Bare Metal Recovery Client with Plug-in Offline Client

To use the Plug-in Server to back up or restore a target NetVault Bare Metal Recovery Client, take the system offline and boot it with the required components. This process is accomplished by booting the NetVault Bare Metal Recovery Client machine with the Plug-in Offline Client Boot System — the media created in the processes explained in Creating a Plug-in Offline Client Boot System. Rather than installing software to the NetVault Bare Metal Recovery Client’s hard drive, this boot system loads a minimal OS to the NetVault Bare Metal Recovery Client’s memory. Loading the OS to the memory leaves the hard drive inactive (offline) and in a suitable state for either backup or restore.

Booting with Plug-in Offline Client

Booting with Plug-in Offline Client

This process entails the configuration of network equipment installed on the target NetVault Bare Metal Recovery Client; that is, loading driver software for the system’s network interface card or small computer system interface (NIC/SCSI) card to memory to use the device and access the system.

The overall boot routine with Plug-in Offline Client can be broken down into two phases. Also, if you are using the Windows PE-based configuration, you can use one of the following procedures to inject drivers into Windows PE when the network driver is not available on the Windows PE image.

 
* 
IMPORTANT: Before starting this procedure, verify the boot order of the target NetVault Bare Metal Recovery Client. The machine’s CD drive must be the first source of a boot for this process to work.

Using a Windows Server 2012-based virtual machine with Plug-in Offline Client for Linux

Using a Windows Server 2012-based virtual machine with Plug-in Offline Client for Linux

If your VMware virtual machine (VM) is based on Windows Server 2012 or 2012 R2 and you use the Plug-in Offline Client for Linux, update the VMware configuration file to use the E1000 adapter.

1
Locate and open the VMware configuration file.
This file is located in the directory where you created the virtual machine. For example, C:\Documents and Settings\My Documents\My Virtual Machines\<machine>\*.vmx.
2
Locate the E100OE entry, and change it to E1000.
3
Save and close the .vmx file.
Documentos relacionados

The document was helpful.

Selecione a classificação

I easily found the information I needed.

Selecione a classificação