지금 지원 담당자와 채팅
지원 담당자와 채팅

NetVault Plug-in for SnapVault Manager 11.4.5 - Release Notes

Quest® NetVault® Backup Plug-in for SnapVault Manager 11.4.5

Quest® NetVault® Backup Plug‑in for SnapVault Manager 11.4.5
These release notes provide information about the Quest® NetVault® Backup Plug‑in for SnapVault Manager release.
•
About this release
•
Known issues
•
System requirements
•
Product licensing
•
Upgrade and installation instructions
•
More resources
•
Globalization
•
About us

About this release

Quest NetVault Backup (NetVault Backup) Plug‑in for SnapVault Manager (Plug‑in for SnapVault Manager) provides a graphical interface that is integrated with the NetVault Backup WebUI to provide a single point of enterprise-wide control and improve the management of NetApp SnapVault solution. This feature lets you back up changed data from multiple storage platforms to a common Snapshot target on NetApp appliances, enabling faster tape less restores.

Plug‑in for SnapVault Manager 11.4.5 is a minor release.

Known issues

The following is a list of issues, including those issues attributed to third-party products, known to exist at the time of release.
 
Table 1. Known issues
Known issue
Issue ID

If you try to restore a non-qtree data directory, the job fails, but the job status shows “Restore Completed.”

NVBU-11148 (26968)

When relocating data during restore, if you include a trailing slash in the Relocate path, the restore job fails.

NVBU-11230 (27071)

On Windows, when you select the SV root directory for a restore job, plug-in restores the data successfully, but the job log includes the following error message:

Error Releasing Secondary Relationship: NDMP_SV_RPL_GENERIC

SnapVault: ERROR 1: The specified relationship is currently involved in a transfer. Release must be done on an idle or broken-off relationship.

Workaround: Release the relationship on the SV secondary filer. Use the snapvault destinations command to find the relationship that must be released.

DNSMP-115 (27020)

After importing a relationship, the plug-in does not display the relationship icon (“R”) on the selection tree until you refresh the Backup window.

NVBU-11245 (27086)

If you cancel a job during relationship initialization, the plug-in fails to remove the relationship. When you try to recreate the relationship, the plug-in displays the message “Relationship is busy.”

DNSMP-117 (27130)

Because all primary systems list the same number of snapshots whether they were taken for that primary system or not, the list contains both valid and invalid snapshots. When an invalid snapshot is selected for a restore, the job fails and logs show the message “No Path.”

DNSMP-118 (27154)

When restoring data to an open system, if you select the Restart Relationship check box, the job reports an error (“No common snapshot to use as the base for resynchronization”) and fails.

Workaround: Recreate the relationship after restoring the data.

DNSMP-119 (27156)

After relocating data to a new directory, the release statement fails and the job logs show the message “No release-able destination found that matches those parameters.”

This message can be ignored.

NVBU-11455 (27376)

System requirements

Before installing Plug‑in for SnapVault Manager 11.4.5, ensure that your system meets the following minimum hardware and software requirements.
 
Table 2. System requirements
Requirement
Details

NetVault Backup versions

NetVault Backup 10.0 or later.

NetApp OSSV versions

NetApp OSSV 2.5 or later.

For complete supported-platform information, see the Quest NetVault Backup Compatibility Guide available at https://support.quest.com/technical-documents.

셀프 서비스 도구
지식 기반
공지 및 알림
제품 지원
소프트웨어 다운로드
기술 설명서
사용자 포럼
비디오 자습서
RSS 피드
문의처
라이센싱 지원가져오기
기술 지원
모두 보기
관련 문서

The document was helpful.

평가 결과 선택

I easily found the information I needed.

평가 결과 선택