Chatee ahora con Soporte
Chat con el soporte

NetVault 11.4.5 - Administration Guide

Introduction Getting started Configuring clients Configuring storage devices Backing up data Managing policies Restoring data Managing jobs Monitoring logs Managing storage devices
Monitoring device activity Managing disk-based storage devices in table view Managing disk-based storage devices in tree view Managing tape libraries in table view Managing tape libraries in tree view Managing tape drives in table view Managing tape drives in tree view Adding shared devices
Managing storage media Managing user accounts Monitoring events and configuring notifications Reporting in NetVault Backup Working with client clusters Configuring default settings for NetVault Backup
About configuring default settings Configuring encryption settings Configuring plug-in options Configuring default settings for post-scripts Configuring default settings for Verify Plug-in Configuring Deployment Manager Settings Configuring Job Manager settings Configuring Logging Daemon settings Configuring Media Manager settings Configuring Network Manager settings Configuring Process Manager settings Configuring RAS device settings Configuring Schedule Manager settings Configuring Web Service settings Configuring Auditor Daemon settings Configuring firewall settings Configuring general settings Configuring security settings Synchronizing NetVault Time Configuring default settings for global notification methods Configuring the reporting utility Configuring NetVault Backup to use a specific VSS provider Configuring default settings using Txtconfig
Diagnostic tracing Managing diagnostic data Using the deviceconfig utility NetVault Backup processes Environment variables Network ports used by NetVault Backup Troubleshooting

Configuring default settings for Deployment Manager

To modify default settings for Deployment Manager:
1
In the Navigation pane, click Change Settings.
2
On the Configuration page, click Server Settings.
3
Under Services, click Deployment Manager. In the Deployment Manager dialog box, configure the following settings.
Table 103. Deployment Manager settings
 
Setting
Description

Maximum simultaneously active deployment processes on server

By default, 50 concurrent deployment processes can run on the server.

To change the number of deployments that can be run in parallel at any time, type or select the new value.

Maximum time a deployment task should wait when processing a client

This setting determines the amount of time the Deployment Manager waits for a response from a remote client during the client addition phase.

The default value is 300 seconds. The timeout interval can be between 30 and 900 seconds.

4
Click Apply to apply the new setting and close the dialog box.

Configuring Job Manager settings

This section includes the following topics:

•
About Job Manager
•
Configuring default settings for Job Manager

About Job Manager

The Job Manager process (nvjobmgr) runs on the NetVault Backup Server and manages the execution of a job.

The Schedule Manager starts the Job Manager. A single instance of Job Manager runs for each job until the completion of the job. The Job Manager reports on the job run status and exit status. This process coordinates with the Data Plug-in and fetches the required information from the NetVault Backup Server. It is also responsible for sending drive and media requests to the Media Manager process.

You can modify the Job Manager settings from the Change Settings page.

Configuring default settings for Job Manager

To configure default settings for Job Manager:
1
In the Navigation pane, click Change Settings.
2
On the Configuration page, click Server Settings.
3
Under Services, click Job Manager. In the Job Manager dialog box, configure the following settings.
Table 104. Job Manager settings
 
Setting
Description

Job Keep Alive rate

Keep-alive messages are used to verify network connection between two NetVault Backup machines and to keep this connection intact. The keep‑alive rate setting controls how often keep-alive messages are sent between the Job Manager running on the server and the Data Plug-in running on a client.

The default value is 5 minutes. To change the interval, type or select a new value. The keep-alive rate is specified in number of minutes.

CLI utility nvjobcreate will return exit status

By default, the nvjobcreate utility returns the Job ID on success and “0” on failure.

When you select this check box, the nvjobcreate utility returns the exit code “0” on success and “1” on failure.

To determine the Job ID number when the nvjobcreate utility is configured to return the exit status, you can use the -jobidfile option. The Job ID number is written to the specified file. For more information about this option, see the Quest NetVault Backup CLI Reference Guide.

4
Click Apply to apply the new settings and close the dialog box.
Documentos relacionados

The document was helpful.

Seleccionar calificación

I easily found the information I needed.

Seleccionar calificación