立即与支持人员聊天
与支持团队交流

NetVault Plug-in for Oracle 12.3 - User Guide

Introducing Quest® NetVault® Backup Plug-in  for Oracle Defining a backup strategy Installing and removing the plug-in Configuring the plug-in Backing up data Using the Oracle Flashback Database Restoring data
Restoring and recovering data: an overview Performing User Managed restores Using advanced User Managed restore procedures Performing RMAN restores Using RMAN types of recovery in a non-RAC environment Using advanced procedures with RMAN restores
Maintaining the Recovery Catalog Using the RMAN CLI Using the plug-in with Oracle RAC Using the plug-in in a failover cluster environment Using the plug-in with Oracle Data Guard Using the plug-in with Oracle Container Databases (CDBs) and Pluggable Databases (PDBs) Troubleshooting

Defining a deployment strategy

Determining a strategy for protecting and recovering a Data Guard environment is essential to deploying and using the plug-in in the Data Guard environment. All strategies are valid for any of the supported deployments as detailed in Deployment.

Back up from Primary only

The simplest strategy is to perform all the backups from the Primary Database Server. You can use these backups to recover the Primary or one of the Standby Database Servers. While this strategy is valid, resource-intensive backup operations affect database performance on the Primary Database Server. With this strategy, the plug-in is installed on the Primary Database Server. Plug‑in for Oracle is only required to be installed on the Standby Database Server when it is targeted for a restore.

Back up from both Primary and Standby

Offloading resource-intensive backup operations to the Standby Database Server is often one of the drivers for deploying Data Guard. The Oracle version dictates how much of the backup operations can be offloaded to the Standby Database Server:

Oracle 10.2.x: Backing up datafiles and archived redo log files can be offloaded to the Standby Database Server while backups of the Control Files and the SPFILE must be performed on the Primary Database Server. In addition, backups of datafiles and archived redo log files can be used to recover either the Primary or Standby Database Server, regardless of whether the backups were taken from the Primary or Standby Database Server. For more information, see RMAN to Back Up and Restore Files in Oracle 10.2.x Data Guard Concepts and Administration.
Oracle 11.x: Backups of datafiles, archived redo log files, Control Files, and SPFILE are interchangeable between the Primary and Standby Database Server, which means that all backups can be performed from one of the Standby Database Servers. In addition, you can use backups to recover either the Primary or Standby Database Server, regardless of whether the backups were taken from the Primary or the Standby Database Server. For more information, see Using RMAN to Back Up and Restore Files in Oracle 11.x Data Guard Concepts and Administration.

While Oracle 11.x does not require all backups to be performed on the Standby Database Server, a valid strategy for an Oracle 11.x environment is to mimic the requirements of a 10.2.x environment. In a 10.2.x environment, only datafiles and archived redo log files are offloaded to the Standby Database Server while the Control Files and SPFILE backups are performed from the Primary Database Server.

Another valid strategy for Oracle 10.2.x and 11.x is to perform Control File and SPFILE backups from the Primary Database Server while alternating the backups of the datafiles and archived redo log files between the Primary Database Server and the Standby Database Server. For example, Incremental Level 0 Backups are performed weekly on the Standby Database Server and the Incremental Level 1 backups are performed daily from the Primary Database Server. In addition, daily backups of the Control File and SPFILE are performed from the Primary Database Server.

Oracle’s Maximum Availability Architecture (MAA) best practices recommend that backups be taken at both the primary and the standby databases to reduce MTTR, in case of double outages and to avoid introducing new site practices on switchover and failover.

With this strategy, Plug‑in for Oracle is installed on both the Primary and at least one of the Standby Database Servers that performs backups.

NOTE: For Oracle versions before Oracle 11.x, backups of SPFILE were assumed to be usable at any other standby database. However, in practice, all standby databases cannot use the same SPFILE. Therefore, RMAN does not allow an SPFILE backup taken at one database site to be used at a different database site. This restriction is in place only when the COMPATIBLE initialization parameter is set to 11.0.0.

The standby database lets you offload all backup operations to one specific standby database, except the backups of SPFILE. However, if the COMPATIBLE initialization parameter is set to 11.0.0, the SPFILE can be backed up to disk and cataloged manually at standby sites where backups are written to tape or NetVault Backup media. The additional metadata stored in SPFILE backup sets enables RMAN to identify which database SPFILE is contained in which backup set. Thus, the appropriate SPFILE backup is chosen during restore from tape or NetVault Backup media.

When implementing a strategy that backs up from both Primary and Standby Servers for an Oracle 10.2.x Data Guard environment, consider the accompanying backup-destination strategy, which is detailed in Defining a Backup Destination strategy.

Because RMAN stores backup metadata in the Recovery Catalog, a backup performed from the Primary Database Server to the FRA results in the RMAN backup pieces created during backup being registered in the Recovery Catalog. On the following day, if a backup performed from the Standby Database Server is also performed to the FRA, the RMAN backup pieces created during backup are also registered in the Recovery Catalog.

Later in the week, if a backup of the FRA is performed to NetVault Backup Media Manager from the Standby Database Server, the FRA-to-NetVault Backup Media Manager backup attempts to access backup sets that were created by the Primary Database Server’s backups to the FRA. Because the primary and standby databases do not share the FRA, the FRA-to-NetVault Backup Media Manager backup fails. RMAN attempts to access backup sets on the Primary Database Server that are not accessible from the Standby Database Server that is performing the FRA-to-NetVault Backup Media Manager backup.

Therefore, for Oracle 10.2.x Data Guard environments, Quest recommends that backups to FRA only be performed from either the Primary Database Server or the Standby Database Server, but not both.

In Oracle 11.x Data Guard environments, the Oracle parameter db_unique_name allows the Recovery Catalog to distinguish the origin of backups to the FRA. When selecting FRA-to-NetVault Backup Media Manager backups, RMAN backs up the backup sets in the FRA of the Database Server performing the FRA-to-NetVault Backup Media Manager backup.

For more information on performing backups to NetVault Backup Media Manager, see Setting backup options. For more information on FRA backups, see Flash Recovery Area (FRA) backups.

Back up from Standby only

Starting with Oracle 11.x, backups of datafiles, archived redo log files, Control Files, and SPFILE are interchangeable between the Primary and Standby Database Server. This interchangeability means that all backups can be performed from one of the Standby Database Servers. With this strategy, Plug‑in for Oracle is installed on both the Primary Database Server and at least one of the Standby Database Servers that performs backups. The plug-in must be installed on the Primary Database Server when it is targeted for a restore; that is, if you want to use the backup of the Standby Database Server to recover the Primary Database Server, you need to install the plug-in on the Primary Database Server.

相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级