立即与支持人员聊天
与支持团队交流

DR Series Software 4.0 - Administrator Guide

Introducing the DR Series system documentation Introducing the DR Series system Setting up the DR Series system Configuring the DR Series system settings Managing containers Managing replications Monitoring the DR Series system Using GlobalView Configuring and using Rapid NFS and Rapid CIFS Configuring and using Rapid Data Access with NetVault Backup and with vRanger Configuring and using RDA with OST
Understanding RDA with OST Guidelines Terminology Supported RDA with OST software and components Best Practices: RDA with OST and the DR Series System Setting client-side optimization Configuring an LSU Installing the RDA with OST plug-in Configuring DR Series system information using NetBackup Backing Up Data From a DR Series System (NetBackup) Using Backup Exec with a DR Series system (Windows) Understanding the OST CLI commands Understanding RDA with OST Plug-In Diagnostic Logs Collecting Diagnostics Using a Linux Utility Guidelines for Gathering Media Server Information
Configuring and using VTL Configuring and Using Encryption at Rest Support, maintenance, and troubleshooting Supported Ports in a DR Series System
2.
Select the server that you want to configure in the Backup Exec Services Manager page, and select Start all services.
4.
In the Connect to Media Server page, log into the media server, and enter a User name, a Password, and click OK.
5.
In the Backup Exec Administrator page, click Network, and click Logon Accounts.
The Logon Account Management page is displayed.
6.
Click New to create a new logon account.
The Add Logon Credentials page is displayed.
7.
In the Account Credentials pane, enter the User name and Password account credentials for the DR Series system, and click OK (for example, the default user name is backup_user).
8.
In the Backup Exec Administrator page, click the Devices tab, and right-click on the local system name that is listed as the root node.
9.
Select Add OpenStorage in the drop-down list.
The Add OpenStorage Device page is displayed.
10.
Configure the Add OpenStorage Device page with the following information, and click OK:
Server—enter the host name or IP address of the DR Series system.
Logon account—select the account from the drop-down list, which has credentials for accessing the DR Series system.
Server type—select the type of plug-in from the drop-down list (DELL OST plug-in).
Logical storage unit—enter the LSU (DR Series system container) name to use.
11.
Click Yes in response to the prompt about making the new device the default destination for new jobs.
12.
Close the Add OpenStorage Device page.
The Restart Services confirmation dialog is displayed (this dialog recommends against restarting the services if any jobs are currently running).
13.
Click Restart Now to restart the Backup Exec services.

Creating backups on the DR Series system using Backup Exec

Creating backups on the DR Series system using Backup Exec

This topic describes how to use Backup Exec to create backups on the DR Series system.

To create backups on the DR Series system using Backup Exec, complete the following:

1.
Launch the Backup Exec Administrator console, and select the Job Setup tab.
2.
Click Backup Tasks in the left navigation panel, and select New job.
The Backup Job Properties page is displayed.
3.
In the left navigation pane of the Backup Job Properties page, select Source, and select Selections.
The Selections page is displayed.
4.
Select the system or node name in the center pane of the Selections page, and click the check boxes that correspond to the files you want backed up.
5.
In the left navigation pane of the Backup Job Properties page, select Destination, and select Device and Media.
The Device and Media page is displayed.
6.
In the Device pane in the Device and Media page, select the DELL OST device in the drop-down list, and click Run Now to start the backup job.
7.
Click the Job Monitor tab to view the progress of the backup job you created.

Optimizing Duplication Between DR Series Systems Using Backup Exec

Optimizing Duplication Between DR Series Systems Using Backup Exec

Backup Exec can replicate backups between two DR Series systems that are part of a defined source and target replication pair. This process uses the deduplication and replication features of the DR Series system via RDA with OST.

Using RDA with OST, backed up data is catalogued which makes it available from the designated media server so that a seamless restore can be performed from either the target or source DR Series system. This is considered an integrated replication, where the appliance does the replication. It is considered to be “optimized” because the data flows from the local appliance directly to the remote appliance in a deduplicated format, and it does not travel through the media server.

When the data is in a deduplicated format (in an optimized form), only new or unique data is copied between the two DR Series systems. Because the duplication job is initiated by Backup Exec, there are two entries in its catalog: one entry is for the source file, while the other entry is for the target file. The backup administrator can restore backup data from either appliance in case of data loss or disaster.

To optimize duplication between DR Series systems, create an additional OST device that points to the target DR Series system, and complete the following steps:

Launch the Backup Exec Administrator console, select the Devices tab, and right-click the target DR Series system.
2.
Select Add OpenStorage in the drop-down list.
The Add OpenStorage Device page is displayed
3.
Configure the Add OpenStorage Device page with the following information:
Server—enter the host name or IP address of the DR Series system.
Logon account—select the account from the drop-down list (or click ... and browse to the account location), which has credentials for accessing the DR Series system.
Server type—select the type of server from the drop-down list (DELL).
Logical storage unit—enter the name of the logical storage unit (LSU), also known as a DR Series system container, to use.
4.
Click Yes in response to the prompt if you want to make the new device the default destination for new jobs.
5.
Close the Add OpenStorage Device page.
6.
Click the Job Setup tab.
7.
In the left navigation pane, select Backup Tasks, and click New job to duplicate backup sets.
The New Job to Duplicate Backup Sets page is displayed.
8.
Select Duplicate existing backup sets, and click OK.
9.
Click the View by Resource tab in the Selections page, and select the dataset you want copied.
10.
In the left navigation pane, select Destination, and select Device and Media.
11.
In Device, select the destination device from the drop-down list (that was created in this procedure), and click Run Now to start the replication operation between the two DR Series systems.
12.
Click the Job Monitor tab to view the progress of the replication operation you created.

Restoring Data from a DR Series System Using Backup Exec

Restoring Data from a DR Series System Using Backup Exec

This topic describes how to use Backup Exec to restore data from a DR Series system.

To restore data from a DR Series system using Backup Exec, complete the following:

Launch the Backup Exec Administrator console, and select the Job Setup tab.
2.
In the left navigation pane, select Restore Tasks, and click New job.
The Restore Job Properties page is displayed.
3.
Click the View by Resource tab in the Selections pane, and select the dataset to be restored.
4.
Click Run Now to start the restore job.
5.
Click the Job Monitor tab to view the progress of the restore job operation you created.
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级