지금 지원 담당자와 채팅
지원 담당자와 채팅

DR Series Software 4.0.4 - Command Line Reference Guide

Introduction to the DR Series System Command Line Reference Guide Introducing the DR Series system Managing the DR Series system
Alerts Commands Authenticate Commands Network
Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --disable=GUID-925B2D94-D583-4966-ABDE-8E3FE14B59FC=1=en-us= network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help
OST RDA Stats Storage Group commands System
System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --hybrid_replication [--enable][--disable][--status] system --rdairgap [--enable][--disable][--set_retention_period <0 days to 365 days>][--get_retention_period][--open][--close][--status] system --rdairgap_schedule [--start_time <HH:MM>][--end_time <HH:MM>][--remove] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --help
User Virtual Machine
Maintaining the DR Series System
Diagnostics Maintenance
Maintenance Command Usage maintenance --filesystem [--start_scan [verify_data | verify_rda_metadata | verify_metadata] [--storage_group <name>] maintenance --filesystem [--stop_scan] maintenance --filesystem [--scan_status] maintenance --filesystem [--scan_report [verbose]] maintenance --filesystem [--repair_status [verbose]] maintenance --filesystem [--repair_history [verbose]] maintenance --filesystem [--scan_restart [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--repair_now] maintenance --filesystem [--reclaim_space] maintenance --filesystem [--clear_quarantine] maintenance --filesystem [--clear_quarantine] maintenance --filesystem --show_throughput maintenance --configuration [--backup] maintenance --configuration [--restore] maintenance --configuration [--reinit_dictionary] maintenance --configuration [--reset_web_certificate] maintenance --configuration --enable_sha256_web_certificate maintenance --hardware [--reinit_nvram] maintenance --hardware [--restore_hw_db] maintenance --hardware [--motherboard_replaced] maintenance --disk [--make_standby [slot num]] [--type <internal | external-<num> | service tag>] --clear_foreign] maintenance --remote_access [--show] maintenance --remote_access [--enable] maintenance --remote_access [--racreset] maintenance --remote_access [--static_ip] [--ip <IPv4/IPv6 address>] [--netmask <netmask>] [--gateway <IPv4/IPv6 address>] [--device <lom1|lom2|lom3|lom4>] maintenance --remote access [--disable] maintenance --vdisk --check_consistency --type <boot|internal|external> [--service_tag <service tag>] maintenance --help
Managing DR Series System Storage Operations
System Storage Operation Commands Connection Container VTL NDMP iSCSI FC Replication Seed Schedule
Data Integrity Checking Additional Linux Commands About us

fc --help <command>

Description

This command displays the command-specific help for the FC commands.

Syntax

fc --help

Result

Usage:   
        fc --show [--verbose]  
             [--target]  
              
        fc --sessions [--topology]  
             [--condensed]  
              
        fc --help  
      
       fc <command> <command-arguments>  
       command can be one of:   
            --show       Displays command specific information.  
            --sessions   Show FC sessions  
      
    For command-specific help, please type fc --help <command>
			eg:  
            fc --help show  

Replication

To allow DR Series system replication operations, ensure that TCP ports 9904, 9911, 9915, and 9916 are enabled. For more information about supported ports for the DR Series system, see the DR Series System Administrator Guide.

The Replication DR Series system CLI command and its options allow you to manage the status of all current replication relationships and tasks on a system by:

  • Displaying the current replication process status information
  • Creating and defining new replication links or relationships to containers
  • Deleting specific replication links
  • Starting and stopping the replication process between source and target containers
  • Limiting the bandwidth consumed during replication
  • Resynchronizing replication between source and target containers
  • Troubleshooting replication connection issues

Software versions 3.1 and later support cascaded replication, which involves a Source, Primary Target, and Secondary Target. Each relationship must be set up individually using two sets of replication add commands.

NOTE: You can set a replication schedule for daily replication operations. For details, see schedule --add --day <day of the week> [--start_time <hh:mm>] [-- stop_time <hh:mm>] [--cleaner] [--replication].

Replication Command Usage

This topic introduces the replication command usage:

  • replication --show [options]
  • replication --add --name --role --peer [options]
  • replication --update --name --role --peer [options]
  • replication --delete --name --role [options]
  • replication --start --name --role [options]
  • replication --stop --name --role [options]
  • replication --limit --speed --target [options]
  • replication --resync --name --role [options]
  • replication --troubleshoot --peer
  • replication --help

NOTE: If you specify a command without supplying the expected value or option, you will be prompted to provide the correct value or option.

replication --show [--name <name>] [--role <source | target>] [--verbose] [--limits]

Description

Displays a detailed summary of replication-related information for a specific replication container in the DR Series system.

Syntax

replication --show --name backup --role source --verbose

Result

Replication Container ID        : 1
Replication Container           : backup
Replication Entry ID            : 1
Replication Role                : Target
Replication MDS Port    			  : 9915
Replication Data Port           : 9916
Replication Source              : DR2K-01
Replication Source IP           : 10.250.208.232
Replication Source Mgmt Name    : DR2K-01
Replication Source Mgmt IP      : 10.250.208.232
Replication Local Data Name     : DR4100-Test
Replication Local Data IP       : 10.250.240.192
Replication Source Container ID : 1
Replication Source Container    : backup
Replication Enabled             : Yes
Replication Compression Enabled : Yes
Replication Encryption          : AES 128-bit

NOTE: To see how to display the limits set for the replication containers, see replication --limit --speed <<num><kbps | mbps | gbps> | default> --target <ip address | hostname>.

관련 문서

The document was helpful.

평가 결과 선택

I easily found the information I needed.

평가 결과 선택