Use the following standard Microsoft Windows uninstall process to remove the Rapid CIFS plug-in from a Windows-based media server. After you uninstall the plug-in, Rapid CIFS will be disabled and “inactive” will be shown next to CIFS Write Accelerator on the CIFS Connection Configuration pane on the Container Statisticspage.
Alternatively, if you want to disable (but not uninstall) the plug-in, you can run the following Rapid CIFS utility command. The utility is located in Program Files\Quest\Rapid CIFS.
rdcifsctl.exe driver -d
![](/ko-kr/technical-documents/image/d2be0eac-01ff-4bc4-8d71-623d9bf7f022)
|
NOTE: Replace this text with a description of a feature that is noteworthy. |
To uninstall the Rapid CIFS plug-in on Windows:
- Click Start, and click Control Panel.
- Under Programs and Features, click Uninstall a program.
- Locate the Rapid CIFS plug-in in the listed of installed programs, right-click,and select Uninstall.
- Click Yes to uninstall the Rapid CIFS plug-in.
Configuring and using Rapid Data Access with NetVault Backup and with vRanger
Rapid Data Access (RDA) with NetVault Backup and with vRanger provides the logical disk interface that can be used with network storage devices. The DR Series system requires a DR Rapid plug-in to integrate its data storage operations with NetVault Backup and vRanger. The plug-in is installed by default on the NetVault Backup and vRanger servers and the DR Series system when the latest software updates are installed. Using the DR Rapid plug-in, the DMAs can take full advantage of key DR Series system features like replication and data deduplication.
When DR Rapid is used with the DR Series system, it offers the following benefits:
- RDA with NetVault Backup and RDA with vRanger protocols provide faster and improved data transfers:
- Focus is on backups with minimal overhead
- Accommodates larger data transfer sizes
- Provides throughput that is better than CIFS or NFS
- DR Rapid and data management application (DMA) integration:
- DMA-to-media server software communication
- DR Series system storage capabilities can be used without extensive changes to DMAs
- Backup and replication operations are simplified by using built-in DMA policies
- DR Series system and DR Rapid ports and write operations:
- Control channel uses TCP port 10011
- Data channel uses TCP port 11000
- Optimized write operations enable client-side deduplication
- Replication operations between DR Series systems:
- No configuration is required on the source or target DR Series system
- Replication is file-based, not container-based
- Replication is triggered by DMA optimized duplication operation
- DR Series system transfers the data file (not the media server)
- After duplication completes, DR Series system notifies DMA to update its catalog (acknowledging the second backup). This makes the DMA aware of the replication location. Restores from either the source or replication target can be used directly from the DMA.
- Supports different retention policies between source and replica
- Replication is set up in the DMA itself, not the DR Series system
For best results, observe the following guidelines for optimal performance with your supported RDA with NetVault Backup and RDA with vRanger operations with the DR Series system:
- Backup, restore, and optimized duplication operations are performed using the RDA with NetVault Backup or RDA with vRanger plug-in.
![](/ko-kr/technical-documents/image/d2be0eac-01ff-4bc4-8d71-623d9bf7f022)
|
NOTE: The plug-in is installed on client systems to support client-side deduplication. |
- Deduplication. The DR Series system supports two deduplication modes:
- Dedupe: When this mode is selected, dedupe writes occur when data is sent from a media server to the DR Series system after optimization is applied to the data; deduplication processing would occur on a NetVault Backup client, for example.
![](/ko-kr/technical-documents/image/d2be0eac-01ff-4bc4-8d71-623d9bf7f022)
|
NOTE: Dedupe mode requires at least 4GB of free RAM on the DR Series system. |