지금 지원 담당자와 채팅
지원 담당자와 채팅

DR Series Software 4.0.3.1 - Command Line Reference Guide

Introduction to the DR Series System Command Line Reference Guide Introducing the DR Series system Managing the DR Series system
Alerts Commands Authenticate Commands Network
Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help
OST RDA Stats Storage Group commands System
System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --hybrid_replication [--enable][--disable][--status] system --rdairgap [--enable][--disable][--set_retention_period <0 days to 365 days>][--get_retention_period][--open][--close][--status] system --rdairgap_schedule [--start_time <HH:MM>][--end_time <HH:MM>][--remove] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --help
User Virtual Machine
Maintaining the DR Series System
Diagnostics Maintenance
Maintenance Command Usage maintenance --filesystem [--start_scan [verify_data | verify_rda_metadata | verify_metadata] [--storage_group <name>] maintenance --filesystem [--stop_scan] maintenance --filesystem [--scan_status] maintenance --filesystem [--scan_report [verbose]] maintenance --filesystem [--repair_status [verbose]] maintenance --filesystem [--repair_history [verbose]] maintenance --filesystem [--scan_restart [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--repair_now] maintenance --filesystem [--reclaim_space] maintenance --filesystem [--clear_quarantine] maintenance --filesystem [--clear_quarantine] maintenance --filesystem --show_throughput maintenance --configuration [--backup] maintenance --configuration [--restore] maintenance --configuration [--reinit_dictionary] maintenance --configuration [--reset_web_certificate] maintenance --configuration --enable_sha256_web_certificate maintenance --hardware [--reinit_nvram] maintenance --hardware [--restore_hw_db] maintenance --hardware [--motherboard_replaced] maintenance --disk [--make_standby [slot num]] [--type <internal | external-<num> | service tag>] --clear_foreign] maintenance --remote_access [--show] maintenance --remote_access [--enable] maintenance --remote_access [--racreset] maintenance --remote_access [--static_ip] [--ip <IPv4/IPv6 address>] [--netmask <netmask>] [--gateway <IPv4/IPv6 address>] [--device <lom1|lom2|lom3|lom4>] maintenance --remote access [--disable] maintenance --vdisk --check_consistency --type <boot|internal|external> [--service_tag <service tag>] maintenance --help
Managing DR Series System Storage Operations
System Storage Operation Commands Connection Container VTL NDMP iSCSI FC Replication Seed Schedule
Data Integrity Checking Additional Linux Commands About us

system --verify_on_read [--enable] [--disable]

Description

Enables or disables data verification on read.

Syntax

system --verify_on_read --enable

Result

Verification of read data Enabled.

system --add_storage --enclosure <service tag>

Description

Adds a data storage expansion shelf (enclosure) to a DR Series system. Each expansion shelf that is added to a DR Series system requires an individual service tag and a license. For information about the maximum allowable expansion shelves and their capacities, see the DR Series System Interoperability Guide and the DR Series System Administrator Guide at support.quest.com/DR-Series.

* 
NOTE: The 300 Gigabyte (GB) drive capacity (2.7 TB) version of the DR Series system does not support the addition of expansion shelf enclosures.

For more information about the required licenses, see system --show [--license] [--verbose] and system --license [--validate] [--add].

* 
NOTE: The recommended process for adding an expansion shelf enclosure involves the following tasks:
•
Use the system --license [--validate] [--add] command to validate and install the license for the expansion shelf enclosure. For specific information, see system --license [--validate] [--add].
•
Power off (if needed) the Dell MD1200 storage array, physically connect the expansion shelf enclosure to the base DR Series system, and power on the expansion shelf enclosure.
•
Use the system --add_storage --enclosure <service tag> command .
* 
NOTE: Each added expansion shelf enclosure must be equal to or greater than each DR Series system internal drive slot capacity (0–11). Because 1 TB drives are the smallest one supported by the expansion shelf enclosure you add, the 600 Gigabyte (GB) DR Series system needs to use 1 TB or larger sized drives in any expansion shelf enclosure added to the base system.
* 
NOTE: To verify the current types of storage on a DR Series system, use the DR Series system CLI command: system --show --storage. For more information, see system --show [--storage].

Syntax

system --add_storage --enclosure CTKHVW1

Result

WARNING: IO to the box will be stopped during enclosure addition.

Do you want to continue (yes/no) [n]? y
Enclosure: "CTKHVW1" added successfully.

system --storage [--set_usage_alert <70% - 90%>]

Description

Used to specify at what storage utilization percentage an alert should be sent.

Syntax

system --storage --set_usage_alert 90

Result

System storage usage alert has been set at 90%.

system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>]

Description

Turns on an LED that is used in locating a specific physical disk or data storage expansion shelf (using the system --storage command) in the DR Series system. Select from the following DR Series system CLI command options:

•
--blink: turns on LED on the physical disk or expansion shelf to identify it.
•
--type <internal | external>: identifies storage as an internal physical disk or external expansion shelf.
•
--service_tag <service tag>: identifies physical disk or expansion shelf by its unique service tag.
•
--disk <slot num>: identifies the disk slot number (if no disk slot is defined, it globally affects all disks).
* 
NOTE: There is a counterpart to this command, in which you can turn off the LED that aids in locating the physical disk or expansion shelf. For more information, see system --storage [--unblink] [--type <internal | external>] [--service_tag>] [--disk <slot num>].
* 
NOTE: The above options are only available on a Physical DR.

Syntax

system --storage --blink --type external --service_tag HCM0PT3

Result

Turned on blinking for all disks in enclosure "HCM0PT3".
관련 문서

The document was helpful.

평가 결과 선택

I easily found the information I needed.

평가 결과 선택