Tchater maintenant avec le support
Tchattez avec un ingénieur du support

DR Series Software 4.0.4 - Command Line Reference Guide

Introduction to the DR Series System Command Line Reference Guide Introducing the DR Series system Managing the DR Series system
Alerts Commands Authenticate Commands Network
Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --disable=GUID-925B2D94-D583-4966-ABDE-8E3FE14B59FC=1=en-us= network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help
OST RDA Stats Storage Group commands System
System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --hybrid_replication [--enable][--disable][--status] system --rdairgap [--enable][--disable][--set_retention_period <0 days to 365 days>][--get_retention_period][--open][--close][--status] system --rdairgap_schedule [--start_time <HH:MM>][--end_time <HH:MM>][--remove] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --help
User Virtual Machine
Maintaining the DR Series System
Diagnostics Maintenance
Maintenance Command Usage maintenance --filesystem [--start_scan [verify_data | verify_rda_metadata | verify_metadata] [--storage_group <name>] maintenance --filesystem [--stop_scan] maintenance --filesystem [--scan_status] maintenance --filesystem [--scan_report [verbose]] maintenance --filesystem [--repair_status [verbose]] maintenance --filesystem [--repair_history [verbose]] maintenance --filesystem [--scan_restart [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--repair_now] maintenance --filesystem [--reclaim_space] maintenance --filesystem [--clear_quarantine] maintenance --filesystem [--clear_quarantine] maintenance --filesystem --show_throughput maintenance --configuration [--backup] maintenance --configuration [--restore] maintenance --configuration [--reinit_dictionary] maintenance --configuration [--reset_web_certificate] maintenance --configuration --enable_sha256_web_certificate maintenance --hardware [--reinit_nvram] maintenance --hardware [--restore_hw_db] maintenance --hardware [--motherboard_replaced] maintenance --disk [--make_standby [slot num]] [--type <internal | external-<num> | service tag>] --clear_foreign] maintenance --remote_access [--show] maintenance --remote_access [--enable] maintenance --remote_access [--racreset] maintenance --remote_access [--static_ip] [--ip <IPv4/IPv6 address>] [--netmask <netmask>] [--gateway <IPv4/IPv6 address>] [--device <lom1|lom2|lom3|lom4>] maintenance --remote access [--disable] maintenance --vdisk --check_consistency --type <boot|internal|external> [--service_tag <service tag>] maintenance --help
Managing DR Series System Storage Operations
System Storage Operation Commands Connection Container VTL NDMP iSCSI FC Replication Seed Schedule
Data Integrity Checking Additional Linux Commands About us

storage_group --delete --name <name> 

Description

Deletes the specified storage group from the DR Series system.

NOTE: Before a storage group can be deleted, all of the containers inside the storage group must first be deleted.

Syntax

storage_group --delete --name StorageGroup_1

Result

Storage Group "StorageGroup_1" has been deleted.

storage_group --help

Description

Displays the list of all storage_group-related options that can be used as a reference when using the DR Series system CLI.

Syntax

storage_group --help

Result

Usage:
  storage_group --show [--name <name>]
		[--verbose]

 storage_group --add --name <name>
             [--compression_mode <fast|best>]  
              
        storage_group --update --name <name>  
             [--compression_mode <fast|best>]  
              
        storage_group --encryption --name <name>  
             [--set <ON|OFF>]  
             [--mode <static | internal>]  
             [--interval <7 days to 70 years>]  
              
        storage_group --delete --name <name>
              
        storage_group --setpassphrase --name <name>
              
        storage_group --help  
      
       storage_group <command> <command-arguments>
       command can be one of:   
            --show            Displays the current list of storage_group.  
            --add             Adds a new storage_group.  
            --update          updates a storage_group.  
            --encryption      updates encryption settings of a storage_group.  
            --delete          Deletes an existing storage_group.  
            --setpassphrase   sets passphrase to a storage_group.  
      
    For command-specific help, please type storage_group --help <command>   
        eg:  
            storage_group --help show

System

This DR Series system CLI command and its options allow you to perform the a variety of system-related tasks, including the following:

  • Displaying the current system configuration
  • Initializing, rebooting, or shutting down the DR Series system
  • Upgrading the DR Series system software
  • Setting the system date and time
  • Setting the network time protocol (NTP)
  • Updating the login password
  • Enabling or disabling telnet access
  • Enabling or disabling marker detection status

NOTE: For information on the system --datacheck commands that are associated with the Data Check feature, see system --datacheck.

System Command Usage

This topic introduces the system command usage:

  • system --show [options]
  • system --init [options]
  • system --reboot
  • system --shutdown
  • system --upgrade
  • system --license [options]
  • system --setname --name
  • system --setdate [options]
  • system --setntp [options]
  • system --hybrid_replication [options]
  • system --rdairgap [options]
  • system --rdairgap_schedule [options]
  • system --setlogin
  • system --telnet [options]
  • system --datacheck [options]
  • system --marker [options]
  • system --verify_on_read [options]
  • system --add_storage --enclosure (Option only available on a physical hardware DR Series system)
  • system --storage [options]
  • system --mgmt_traffic (Option only available on a physical hardware DR Series system)
  • system --backup_traffic (Option only available on a physical hardware DR Series system)
  • system --replication_traffic (Option only available on a physical hardware DR Series system)
  • system --opdup_traffic (Option only available on a physical hardware DR Series system)
  • system --help

NOTE: If you specify a command without supplying the expected value or option, you will be prompted to provide the correct value or option.

Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation