DR Series Software 4.0.3.1 - Command Line Reference Guide

Chatee ahora con Soporte

Alerts Command Usage alerts --show [--email] alerts --show [--snmp] alerts --show [--events] [--index <[-]number> [--count <number>] [--all] alerts --show [--alerts] [--index <[-] number>] [--count <number>] [--all] alerts --show [--summary] alerts --email [--relay_host <server name>] alerts --email [--appliance_alerts <yes | no>] alerts --email [--software_updates <yes | no>] alerts --email [--daily_report <yes | no>] alerts --email [--daily_report_time <0–24 hr>] alerts --email [--sender_email <email address>] alerts --test_email alerts --snmp_add --host <server name> --port <number> --community <name> alerts --snmp_delete --host <server name> alerts --snmp_disable --host <server name> alerts --snmp_enable --host <server name> alerts --snmp_trap_email [--enable] [--disable] alerts --help

Authenticate Commands

Authenticate Command Usage authenticate --show [--users] authenticate --show [--domain <domain name>] authenticate --show [--login_group] authenticate --join --domain <domain name> [--ou <org-unit name>] --user <user name> authenticate --leave [--user <user name>] [--force] authenticate --update --kerberos authenticate --add [--user <user name>] authenticate --add [--login_group <DOMAIN\LOGIN GROUP>] authenticate --delete--user <user name> authenticate --delete [--login_group <DOMAIN\LOGIN GROUP>] authenticate --set --user <user name> authenticate --guestmode [--enable] [--disable] authenticate --guestmode [--enable] authenticate --guestmode [--disable] authenticate --server_signing --mode <auto | mandatory | disabled> authenticate --help

Network

Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help

OST

OST Command Usage ost --show [--config] [--file_history] [--name <name>] [--active_files] [--name <name>] [--clients] [--limits] ost --update --opdup_encryption <none | aes128 | aes256> ost --delete_client --name <OST Client Hostname> ost --update_client --name <OST Client Hostname> --mode <auto | passthrough | dedupe> ost --limit --speed <<num><KBps | MBps | GBps | default> --target <ip address | hostname> ost --partial_images --containerid <Container id> [--delete <Partial image path>] [--timeout <> 0>] ost --help

RDA

RDA Command Usage rda --show [--config] [--file_history] [--name <name>] [--active_files] [--name <name>] [--clients] [--limits] rda --update --opdup_encryption <none | aes128 | aes256> rda --delete_client --name <RDA Client Hostname> rda --update_client --name <RDA Client Hostname> --mode <auto| passthrough| dedupe> rda --limit --speed <<num><KBps| MBps| GBps> | default> --target <ip address | hostname> rda --partial_images --containerid <Container id> [--delete <Partial image path>] [--timeout <> 0>] rda --help

Stats

Stats Command Usage stats --system stats --cpu stats --memory stats --network stats --datacheck stats --nfs stats --cifs stats --ost stats --rds stats --ndmp stats --ndmp_completed stats --iscsi [--verbose] stats --fc [--iostat] [--linkstat] stats --container --name <name> stats --storage_group --name <name> stats --replication [--name <name>] stats --cleaner stats --clients [--type <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] stats --reset [--nfs] [--cifs] [--ost] [--rds] [--datacheck] stats --reset --datacheck stats --seed stats --help stats --datacheck stats --datacheck Command Usage stats --help datacheck

Storage Group commands

Storage Group Command Usage storage_group --show [--name <name>] [--verbose] storage_group --add --name <name> [--compression_mode <fast|best>] storage_group --update --name <name> [--compression_mode <fast|best>] storage_group --encryption --name <name> [--set <ON | OFF>] [--mode <static|internal> <--interval <7 days to 70 years>] storage_group --setpassphrase --name <name> storage_group --delete --name <name> storage_group --help

System

System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --hybrid_replication [--enable][--disable][--status] system --rdairgap [--enable][--disable][--set_retention_period <0 days to 365 days>][--get_retention_period][--open][--close][--status] system --rdairgap_schedule [--start_time <HH:MM>][--end_time <HH:MM>][--remove] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --help

User

Virtual Machine

Virtual Machine Command Usage virtual_machine -- show [--service_tag <service tag>] virtual_machine --show --summary virtual_machine --update [--host <ip address | hostname>] [--name <administrator name>] [--email <email address>] [--company <company name>] [--comments <comments>] virtual_machine --register [--host <ip address| hostname>] [--name <administrator name>] [--email <email address>] [--company <company name>] [--comments <comments>] virtual_machine --unregister [--force] virtual_machine –delete --service_tag <service tag>

Maintaining the DR Series System

Diagnostics

Maintenance

Managing DR Series System Storage Operations

System Storage Operation Commands Connection

Container

VTL

VTL Command Usage vtl --show [--name <name>] vtl --show --verbose [--name <name>] vtl --update_carts --name <name> --add --no_of_tapes <number> vtl --activate --name <name> [--force <yes|no>] vtl --deactivate --name <name> vtl --rescan --name <name> [--force <yes|no>] vtl --set_rw --name <name> [--id <number>] vtl --show_replstate --name <name> vtl --help

NDMP

NDMP Command Usage ndmp --show ndmp --update [--port <port number>] ndmp --help

iSCSI

ISCSI Command Usage iscsi --show [--user] iscsi --setpassword iscsi --sessions iscsi --help

FC Command Usage fc --show [--verbose] [--target] fc --sessions [--topology] [--condensed] fc --help <command>

Replication

Replication Command Usage replication --show [--name <name>] [--role <source | target>] [--verbose] [--limits] replication --show replication --show [--limits] replication --add --name <name> --role <source | target> --peer <ip address | hostname> [--peer_name <name>] [--peer_group_name <name>] [--replication_traffic <ip address | hostname>] [--encryption <none | aes128 | aes256>][--username <user name>] replication --update --name <name> --role <source | target> [--peer <ip address | hostname>] [--encryption <none | aes128 | aes256>] [--username <user name>] replication --delete --name <name> --role <source | target> [--force] replication --start --name <name> --role <source | target> replication --stop --name <name> --role <source | target> replication --limit --speed <<num><KBps | MBps | GBps> | default> --target <ip address | hostname> replication --resync --name <name> --role <source | target> replication --troubleshoot --peer <ip address | hostname> replication --help

Seed

Seed Command Usage seed --create --op <import | export> [--enc_type <aes128 | aes256>] [--storage_group_name <name>] seed --add_container --name <container name> seed --add_device --server <server name> --volume <volume> --username <username> --domain <domain name> seed --cleanup seed --remove_device seed --show seed --start seed --help

Schedule

Schedule Command Usage schedule --show [--cleaner] schedule --show [--replication] [--name <name>] schedule --add --day <day of the week> [--cleaner] [--replication] [--start_time <hh:mm>] [-- stop_time <hh:mm>] [--name <name>] schedule --delete --day <day of the week> [--cleaner] [--name <name>] [--replication] schedule --help

Data Integrity Checking

About Data Check

Priority Write Verify Scans Continuous Data Verification Scans Data Check CLI Commands Data Check Options

Data Check: Namespace Scan Option Data Check: Blockmap Scan Option Data Check: All Data Scan Option

System --Datacheck

System --Datacheck Command Usage system --datacheck system --datacheck --disable system --datacheck --enable system --datacheck --throttle system --help datacheck

stats --datacheck

stats --datacheck Command Usage stats --datacheck

Additional Linux Commands

grep more

About us

FC Command Usage

This topic introduces the DR Series system CLI commands that allow you to manage Fibre Channel connections when you are using virtual tape library (VTL) containers. These commands include:

•

fc --show

•

fc --sessions

•

fc --help

fc --show [--verbose] [--target]

fc --sessions [--topology] [--condensed]

Description

This command displays the current Fibre Channel sessions in the current DR system.

Syntax

fc --sessions --topology

fc --sessions --condensed

Result

For fc --sessions --topology:

Target port: 50:00:65:b6:33:63:14:88
Initiators connected:
10:00:00:90:fa:a0:ae:0a
50:0a:09:80:00:88:a7:71
50:0a:09:80:06:8d:9a:40
c0:03:ff:bd:1d:69:00:48

Target port: 50:00:65:b6:33:63:14:89
Initiators connected:
10:00:00:90:fa:cf:49:5e
c0:03:ff:bd:1d:69:00:54
c0:03:ff:bd:1d:69:00:58
c0:03:ff:bd:1d:69:00:60

For fc --sessions --condensed:

Initiators connected.
10:00:00:90:fa:a0:ae:0a
50:0a:09:80:00:88:a7:71
50:0a:09:80:06:8d:9a:40
c0:03:ff:bd:1d:69:00:48
10:00:00:90:fa:cf:49:5e
c0:03:ff:bd:1d:69:00:54
c0:03:ff:bd:1d:69:00:58
c0:03:ff:bd:1d:69:00:60

fc --help <command>

Description

This command displays the command-specific help for the FC commands.

Syntax

fc --help

Result

Usage:
fc --show [--verbose]
[--target]

fc --sessions [--topology]
[--condensed]

fc --help

fc <command> <command-arguments>
command can be one of:
--show Displays command specific information.
--sessions Show FC sessions

For command-specific help, please type fc --help <command>
eg:
fc --help show

Documentos relacionados

The document was helpful.

Seleccionar calificación

I easily found the information I needed.

Seleccionar calificación

Seleccione su producto:

Con el fin de ofrecerle un mejor servicio, complete el campo Motivo del chat:

Soluciones recomendadas para su problema

DR Series Software 4.0.3.1 - Command Line Reference Guide

FC Command Usage

fc --show [--verbose] [--target]

fc --sessions [--topology] [--condensed]

fc --help <command>