Chatee ahora con Soporte
Chat con el soporte

DR Series Software 4.0.3.1 - Command Line Reference Guide

Introduction to the DR Series System Command Line Reference Guide Introducing the DR Series system Managing the DR Series system
Alerts Commands Authenticate Commands Network
Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help
OST RDA Stats Storage Group commands System
System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --hybrid_replication [--enable][--disable][--status] system --rdairgap [--enable][--disable][--set_retention_period <0 days to 365 days>][--get_retention_period][--open][--close][--status] system --rdairgap_schedule [--start_time <HH:MM>][--end_time <HH:MM>][--remove] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --help
User Virtual Machine
Maintaining the DR Series System
Diagnostics Maintenance
Maintenance Command Usage maintenance --filesystem [--start_scan [verify_data | verify_rda_metadata | verify_metadata] [--storage_group <name>] maintenance --filesystem [--stop_scan] maintenance --filesystem [--scan_status] maintenance --filesystem [--scan_report [verbose]] maintenance --filesystem [--repair_status [verbose]] maintenance --filesystem [--repair_history [verbose]] maintenance --filesystem [--scan_restart [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--repair_now] maintenance --filesystem [--reclaim_space] maintenance --filesystem [--clear_quarantine] maintenance --filesystem [--clear_quarantine] maintenance --filesystem --show_throughput maintenance --configuration [--backup] maintenance --configuration [--restore] maintenance --configuration [--reinit_dictionary] maintenance --configuration [--reset_web_certificate] maintenance --configuration --enable_sha256_web_certificate maintenance --hardware [--reinit_nvram] maintenance --hardware [--restore_hw_db] maintenance --hardware [--motherboard_replaced] maintenance --disk [--make_standby [slot num]] [--type <internal | external-<num> | service tag>] --clear_foreign] maintenance --remote_access [--show] maintenance --remote_access [--enable] maintenance --remote_access [--racreset] maintenance --remote_access [--static_ip] [--ip <IPv4/IPv6 address>] [--netmask <netmask>] [--gateway <IPv4/IPv6 address>] [--device <lom1|lom2|lom3|lom4>] maintenance --remote access [--disable] maintenance --vdisk --check_consistency --type <boot|internal|external> [--service_tag <service tag>] maintenance --help
Managing DR Series System Storage Operations
System Storage Operation Commands Connection Container VTL NDMP iSCSI FC Replication Seed Schedule
Data Integrity Checking Additional Linux Commands About us

replication --show [--limits]

Description

Displays the limits set for your replication containers on the DR Series system.

Syntax

Result

For more information, see replication --limit --speed <<num><kbps | mbps | gbps> | default> --target <ip address | hostname>.

replication --add --name <name> --role <source | target> --peer <ip address | hostname> [--peer_name <name>] [--peer_group_name <name>] [--replication_traffic <ip address | hostname>] [--encryption <none | aes128 | aes256>][--username <user name>]

Description

Adds a new replication link to a container on the DR Series system, for which you need to define its name, role, peer appliance IP address/hostname , peer name, peer group name, user name on the peer system, and encryption level to apply. The peer group name is the name of the remote container’s group to replicate to/from, and this parameter is applicable only if a remote container is not present.

There are three options for encryption: none,(Advanced Encryption Standard), using128-bit cryptographic keys, and aes256 (using 256-bit AES cryptographic keys).

If the username is a domain login (for example, domain\username), ensure that '\' characters and spaces are either escaped or in quotes.

Syntax

Result

replication --update --name <name> --role <source | target> [--peer <ip address | hostname>] [--encryption <none | aes128 | aes256>] [--username <user name>]

Description

Updates an existing replication link to a container in a DR Series system and allows you to change the corresponding role, peer IP address or host name, the encryption being used, and user name based on the DR Series system CLI command options you specify.

Syntax

Result

When replication is enabled on the container, you must first disable it before you can update it. To disable replication on a container, enter the DR Series system CLI replication --stop command and define the container name and role:

Disables replication on a container:

replication --delete --name <name> --role <source | target> [--force]

Description

Deletes an existing replication link to a container in a DR Series system.

Syntax

If you attempt to delete a container that already has replication enabled, this displays the following message:

NOTE: If the replication state of the link is enabled, you must use the replication --stop command to disable replication before you can delete the replication link. For more information, see replication --stop --name <name> --role <source | target>.

Deletes the existing replication link to a container.

Result

NOTE: The DR Series system CLI --force command is optional, and this command allows you to force the deletion of an existing replication link (such as when communications between the source and target are not working).
Documentos relacionados

The document was helpful.

Seleccionar calificación

I easily found the information I needed.

Seleccionar calificación