Chatee ahora con Soporte
Chat con el soporte

NetVault Plug-in for Hyper-V 10.5 - User Guide

Performing backups

The procedure for performing image-level backups, with or without indexing, includes the steps outlined in the following sections.
•
Selecting data for a backup
•
Setting backup options
•
Finalizing and submitting the job

Selecting data for a backup

You must use sets — Backup Selection Set, Backup Options Set, Schedule Set, Target Set, and Advanced Options Set — to create a backup job.
 
* 
TIP: To use an existing set, click Create Backup Job, and select the set from the Selections list.
1
In the Navigation pane, click Create Backup Job.
You can also start the wizard from the Guided Configuration link. In the Navigation pane, click Guided Configuration. On the NetVault Configuration Wizard page, click Create backup jobs.
2
In Job Name, specify a name for the job.
Assign a descriptive name that lets you easily identify the job when monitoring its progress or restoring data. The job name can contain alphanumeric and non-alphanumeric characters, but it cannot contain non-Latin characters. On Windows®, there is no length restriction. However, a maximum of 40 characters is recommended.
3
Next to the Selections list, click Create New.
4
In the list of plug-ins on the NetVault Backup Selections page, open Hyper-V Plugin, and expand the localhost or <clusterName> node to display the list of VMs.
5
Select the localhost or <clusterName> node to include every VM that exists at the time of backup, or select individual VMs to back up a specific set of VMs.
 
* 
IMPORTANT: If VMs are explicitly selected with a green check mark, only the selected VMs are included in the backup, even if new VMs have been added to the Hyper‑V® Server since the last backup.
6
Click Save to save the set, enter a name in the Create New Set dialog box, and click Save.
The name can contain alphanumeric and non-alphanumeric characters, but it cannot contain non-Latin characters. On Windows®, there is no length restriction. However, a maximum of 40 characters is recommended on all platforms.

Setting backup options

The next step involves creating the Backup Options Set or selecting an existing one. There are two options available: Maximum Number of Parallel Streams and Enable indexing for File Level Recovery.
•
The default for Maximum Number of Parallel Streams is 4 for Windows Server® 2012 and 2012 R2 and 1 for Windows Server 2008 R2. If your environment uses Windows Server 2012 or 2012 R2, you can increase the setting up to 32.
•
The Enable indexing for File Level Recovery option is disabled by default. Indexing lets you restore individual files and directories from image-level backups of VMs.
File-level indexing is available to VMs that use the following file systems:
•
Windows®: NTFS
•
Extended file systems: EXT2, EXT3, and EXT4
File-level indexing does not affect the size of the backup. However, it increases the size of the backup index and the total backup time. The amount of time taken to perform file-level indexing depends on several factors, including the number of files, fragmentation of files on the volumes, network traffic, and load on the Hyper-V Server.
The plug-in also supports volumes managed by Logical Volume Manager (LVM) on Linux-based systems and Logical Disk Manager (LDM) on Windows-based systems as single or spanned disks. It does not support Windows Server 2012 ReFS (Resilient File System) and Striped Disks or Storage Spaces.
 
* 
TIP: To use an existing set, in the Plugin Options list, select the set that you want to use.
1
Next to the Plugin Options list, click Create New.
2
In the Maximum Number of Parallel Streams box, enter the applicable number.
If your environment uses Windows 2012 or 2012 R2, you can enter up to 32 to improve load balancing or performance, or both. However, if you are using tape drives, the number of parallel backup streams selected must be equal to or less than the number of available drives.
3
If you might want to perform restores at the file level, select the Enable indexing for File Level Recovery option.
4
Click Save, specify a name for the set in the Create New Set dialog box, and click Save.
The name can contain alphanumeric and non-alphanumeric characters, but it cannot contain non-Latin characters. On Windows®, there is no length restriction; however, a maximum of 40 characters is recommended.

Finalizing and submitting the job

1
Use the Schedule, Target Storage, and Advanced Options lists to configure any additional required options.
2
Click Save or Save & Submit, whichever is applicable.
 
* 
TIP: To run a job that you have already created and saved, select Manage Job Definitions in the Navigation pane, select the applicable job, and click Run Now.
You can monitor progress on the Job Status page and view the logs on the View Logs page. For more information, see the Dell NetVault Backup Administrator’s Guide.
Documentos relacionados

The document was helpful.

Seleccionar calificación

I easily found the information I needed.

Seleccionar calificación