Chatee ahora con Soporte
Chat con el soporte

NetVault Bare Metal Recovery 10.5 - User Guide for Plug-ins

Introducing Dell™ NetVault™ Bare Metal Recovery Plug-ins Deploying NetVault Bare Metal Recovery Using the Plug-in Offline Client Using Plug-in Live Client for Windows® Using Plug-in Live Client for Linux® NetVault Bare Metal Recovery physical-to-virtual recovery Troubleshooting

Booting the NetVault Bare Metal Recovery Client from a LiveCD

3
If the LiveCD automatically mounted the USB/CD drive, use the “mount -l” command to find the path where the device is mounted.
a
Use the “ls -l /dev/disk/by-id/usb*” command to find the USB devices on the system.
5
To start drdaemon, run the “vaultdr_client.sh” command.
6
If you configured NetVault Bare Metal Recovery to use a port other than the default “10000,” exit the NetVault Bare Metal Recovery Daemon dialog box, and enter the new port number manually.
a
To exit the NetVault Bare Metal Recovery Daemon dialog box, press <Ctrl+C>.
drdaemon -p port_number
NOTE: You can enter the -o mpath and -p port_number options together.

Backing up data with Plug-in Offline Client

Disk Partitions: All (or individual) partitions can be selected for backup.
Mounted Volumes (Linux® and UNIX®): All of which are backed up as individual partitions.
NOTE: The Master Boot Record (MBR) and the Partition Table items are backed up automatically when a partition (all or individual) is backed up using the Plug-in Server. Therefore, these items are not available to select for a backup.
Before backing up any portion of a NetVault Bare Metal Recovery Client’s hard drive, Dell recommends that you note the Disk Size and the Disk Geometry of the selected drive. If these items are not accounted for, a restore might fail.
2
In the Navigation pane, click Create Backup Job.
3
Next to the Selections list, click Create New.
4
On the NetVault Backup Selections page, double-click the NetVault Backup Server (the system containing the Plug-in Server) to open it.
The Device Geometry dialog box displays details about the partition structure of the selected disk.
Partitions: Each individual partition is listed here by number and the partition type.
Active: Displays the current state of the partition (“Yes” or “No”).
Start Cyl: Displays the origination point (cylinder) for the various partitions.
End Cyl: Displays the partition’s endpoint (cylinder).
Size: Displays the size of each partition.
Type: Displays the type of partition.
The Device Size dialog box displays details about the size of the selected disk.
Device: The number and type of the disk.
Size: The size of the selected disk.

Backing up data

When Disk Raw Mode is selected, not only is the disk in use backed up, but the entire disk is as well. For example, if 6GB are in use on a 30GB partition, 30GB of media is used to back up the disk. Only use the Disk Raw Mode option when a complete hard drive is selected for a Plug-in Server backup (that is, not an individual partition).
Dynamic disks must be backed up by using Disk Raw Mode to maintain partition information.

Selecting data for a backup

2
In the Navigation pane, click Create Backup Job.
You can also start the wizard from the Guided Configuration link. In the Navigation pane, click Guided Configuration. On the NetVault Configuration Wizard page, click Create backup jobs.
3
In Job Name, specify a name for the job.
Assign a descriptive name that lets you easily identify the job when monitoring its progress or restoring data. The job name can contain alphanumeric and non-alphanumeric characters, but it cannot include non-English characters. On Linux®, the names can have a maximum of 200 characters. On Windows®, there is no length restriction. However, a maximum of 40 characters is recommended on all platforms.
4
Next to the Selections list, click Create New.
6
In the list that appears, locate the Plug-in Server (labeled “VaultDR APM”), and double-click it to open it and display the hard disks on the client system.
Primary Partition: Each hard disk can contain up to four different “true partitions.” They are called the primary partitions, and can be individually selected for backup.
Extended Partition: This partition is the space on the hard disk not allocated to the primary partitions. This type of partition cannot be selected for a backup. To add it, the entire drive must be selected.
Logical Partition: Logical partitions allow multiple system images to run in one machine. This option can be multiple instances of the same OS or different systems. Logical partitions can be individually selected for a backup.
8
Click Save, enter a name in the Create New Set dialog box, and click Save.
The name can contain alphanumeric and non-alphanumeric characters, but it cannot include non-English characters. On Linux®, the names can have a maximum of 200 characters. On Windows®, there is no length restriction. However, a maximum of 40 characters is recommended on all platforms.
Documentos relacionados

The document was helpful.

Seleccionar calificación

I easily found the information I needed.

Seleccionar calificación