Chatee ahora con Soporte
Chat con el soporte

vRanger 7.8 - User Guide

Introduction Configuring vRanger
Configuration overview Configuring vRanger through the Startup Wizard Configuring vRanger manually Supplemental instructions: additional repository types
Using vRanger Backup Restore Replicate VMs Reports Integrating and monitoring vRanger Using the vRanger Console vAPI Cmdlet details
Add-BackupGroupEntity Add-BackupJobTemplate Add-CIFSRepository Add-DdbReplicationRepository Add-DdbRepository Add-EsxHost Add-HypervCluster Add-HypervHost Add-HypervRestoreJobTemplate Add-NFSRepository Add-NVSDRepository Add-PhysicalMachine Add-RdaRepository Add-ReplicationJobTemplate Add-RestoreFromManifestJobTemplate Add-RestoreJobTemplate Add-VirtualAppforLinuxFLR Add-VirtualAppforLinuxFLRVA Add-VirtualCenter Disable-Job Dismount-LinuxVolume Enable-Job Get-AddressBook Get-BackupGroupEntity Get-CatalogSearchData Get-CatalogStatus Get-ConfigOption Get-Connection Get-CurrentTemplateVersionID Get-Datastore Get-GlobalTransportFailover Get-InventoryEntity Get-IsInventoryRefreshing Get-Job Get-JobTemplate Get-MonitorLog Get-Network Get-PhysicalMachineDiskMap Get-Repository Get-RepositoryJob Get-RepositorySavePoint Get-RestoreDiskMap Get-SavepointDisk Get-SavepointManifest Get-Savepoints Get-TransportFailover Get-VirtualApplianceConfig Get-VirtualApplianceDeploymentStatus Get-VirtualApplianceReconfigStatus Get-VirtualMachinesUnderInventory Get-VmDisk Get-VMDKVolume Install-VirtualAppliance Mount-LinuxVolume New-BackupFlag New-BackupGroupMember New-Daily Schedule New-EmailAddress New-IntervalSchedule New-MonthlySchedule New-ReplicationFlag New-RestoreFlag New-SMTPServer New-TransportConfiguration New-VirtualAppliance New-WeeklySchedule New-YearlySchedule Remove-AllMount Remove-BackupGroupEntity Remove-BackupGroupMember Remove-Catalog Remove-DdbStorageUnit Remove-JobTemplate Remove-LinuxVolume Remove-Repository Remove-SavePoint Remove-VirtualAppliance Remove-VirtualApplianceConfiguration Run-JobsNow Run-ReplicationFailover Run-ResumeReplicationFailover Run-TestReplicationFailover Set-Cataloging Set-CBTonVM Set-LinuxVolume Set-MountPath Set-Resources Stop-vRangerJob Update-BackupJobTemplate Update-GlobalTransportFailover Update-HypervRestoreJobTemplate Update-Inventory Update-ReplicationJobTemplate Update-RestoreJobTemplate Update-VirtualAppliance Update-VirtualApplianceConfiguration
About us

Configuring VA networking

Previous Next


Configuring vRanger > Supplemental instructions: additional repository types > Configuring VA networking
If you have deployed one or more VAs using a static IP configuration, and you need to change that configuration after deployment, you must do so from within the VA.
To configure VA networking, complete the following tasks:
•
Logging in to the VA
•
Changing the hostname
•
Changing the network configuration
•
Configuring DNS
Logging in to the VA
Complete the steps in the following procedure to log in to the VA.
To log in to the VA:
1
From your VI Client, find the VA, and power it on.
2
Using the console, log in as root to the VA, using the following default credentials:
▪
Username: root
▪
Password: vzroot1
If you supplied your own password during the VA deployment, use that password.
Changing the hostname
Complete the steps in the following procedure to change hostname.
To change the hostname:
1
Log in to the VA.
2
Using the VI text editor, edit the network configuration file:
vi /etc/sysconfig/network
3
Change the hostname to the new value, and save the file.
4
Restart the VM by typing reboot at the prompt.
Changing the network configuration
Optionally, you can complete the steps in the following procedure to change the network configuration.
To change the network configuration:
1
Log in to the VA.
2
Using the VI text editor, edit the configuration file for eth0:
vi /etc/sysconfig/ifconfig.eth0
3
Edit the configuration file as needed.
The following text is shown as an example:
ONBOOT=yes
SERVICE=ipv4-static
IFACE=eth0
IP=<static IP of VA>
GATEWAY=<IP of gateway>
PREFIX=<this entry is the subnet mask — your values may differ>
BROADCAST=<your broadcast IP — the highest IP in the VA’s subnet.>
4
Save the file.
5
Restart the VM by typing reboot at the prompt.
Configuring DNS
Depending on your environment, you might have to configure the VA with DNS nameserver information. The steps to change an existing configuration are the same.
To configure DNS:
1
Log in to the VA.
2
Using the VI text editor, edit the resolv.conf file:
vi /etc/resolv.conf
3
Enter the following text, substituting the appropriate values where indicated:
search <domain1> <domain2> <domain3>
nameserver <IP address>
nameserver <IP address>
4
Save the file.
5
Restart the VA by typing reboot at the prompt.

Disabling Distributed Resource Scheduler (DRS) for the vRanger VA

Previous Next


Configuring vRanger > Supplemental instructions: additional repository types > Disabling Distributed Resource Scheduler (DRS) for the vRanger VA
If the vRanger appliance is configured on hosts that are part of a DRS-enabled cluster, the VAs might be migrated to a different host due to DRS and high-availability (HA) activity. This change causes replication failures as the VA is no longer in the expected location — as configured in vRanger. To prevent this disruption, it is important to disable DRS for the vRanger VAs.
To disable DRS for the vRanger VA:
1
In your VI client, find the cluster or clusters that contain the vRanger VAs.
2
Right-click the cluster, and select Edit Settings.
3
In the Cluster Settings dialog box, select Virtual Machine Options.
4
Search for or find the vRanger VAs. Right-click each VA, and select manual.

Using vRanger

Previous Next


vRanger user interface (UI) overview
The vRanger UI consists of four views: My Inventory, My Repositories, My Jobs, and My Reports. Each view features the Main toolbar and each pane’s toolbar.
In the left pane within these views, data appears nested in a tree structure. In general, the information that appears in the right pane depends on the node that you select in the left pane. Each node has a distinct icon, making navigation easy and hierarchy clear.
For instructions on using the Startup Wizard to configure the software for your environment, see Configuring vRanger through the Startup Wizard.

vRanger user interface (UI) overview

Previous Next


Using vRanger
Using vRanger
The vRanger UI consists of four views: My Inventory, My Repositories, My Jobs, and My Reports. Each view features the Main toolbar and each pane’s toolbar.
In the left pane within these views, data appears nested in a tree structure. In general, the information that appears in the right pane depends on the node that you select in the left pane. Each node has a distinct icon, making navigation easy and hierarchy clear.
For instructions on using the Startup Wizard to configure the software for your environment, see Configuring vRanger through the Startup Wizard.
Documentos relacionados

The document was helpful.

Seleccionar calificación

I easily found the information I needed.

Seleccionar calificación