Encrypting data in transport over a network
Rapid Recovery Core includes an encryption feature. You can encrypt all data in transport over a network. Quest recommends enabling this encryption setting when data between your Core and protected machines (or between two Cores such as for replication) must flow over the public or untrusted networks such as the internet.
While there is only a small performance cost involved in enabling this encryption, if your Cores and protected machines are within the confines of a private local area network, you can disable this option with confidence.
Please read the following information and adjust your environment accordingly.
By default, when protecting a machine using the Protect Machine wizard or the Protect Multiple Machines wizard, encryption for the data in transport over a network is enabled. If you select advanced options for the wizard, you can view the Encryption options. On the Encryption page of the wizard, if preferred, you can clear the option Encrypt the data in transport over a network.
|
|
NOTE: If you do not select Advanced options in the wizard, encryption for data in transport is enabled nevertheless. |
After completing the relevant protection wizard, you can always enable or disable encryption for snapshot data by changing transfer settings at the machine level. Select the protected machine, click Settings, and under Transfer settings, for the setting Encrypt snapshot data, select Yes to enable encryption or select No to disable encryption during transport. For specific details, see Viewing and modifying protected machine settings.
Applying or removing encryption keys
You can secure the data protected on your Core at any time by defining an encryption key and applying it to one or more protected machines in your repository. You can apply a single encryption key to any number of protected machines, but any protected machine can only use one encryption key at a time.
The scope of deduplication in Rapid Recovery is limited to protected machines using the same repository and encryption key. Therefore, to maximize the value of deduplication, Quest recommends applying a single encryption key to as many protected machines as is practical. However, there is no limit to the number of encryption keys you can create on the Core. Thus, if legal compliance, security rules, privacy policies, or other circumstances require it, you can add and manage any number of encryption keys. You could then apply each key to only one protected machine, or any set of machines in your repository.
Any time you apply an encryption key to a protected machine, or dissociate an encryption key from a protected machine, Rapid Recovery takes a new base image for that machine upon the next scheduled or forced snapshot. The data stored in that base image (and all subsequent incremental snapshots taken while an encryption key is applied) is protected by a 256-bit advanced encryption standard. There are no known methods for compromising this method of encryption.
If you change the name or passphrase for an existing encryption key currently used for a protected machine, then upon the next scheduled or forced snapshot, Rapid Recovery Core captures and reflects the updated properties of the key. The data stored in that image (and all subsequent incremental snapshots taken while an encryption key is applied) is protected by a 256-bit advanced encryption standard.
Once an encryption key is created and applied to a protected machine, there are two concepts involved in removing that encryption. The first is to disassociate the key from the protected machine. Optionally, once the encryption key is disassociated from all protected machines, it can be deleted from the Rapid Recovery Core.
This section includes the following topics:
- Associating an encryption key with a protected machine
- Applying an encryption key from the Protected Machines page
- Disassociating an encryption key from a protected machine
Associating an encryption key with a protected machine
You can apply an encryption key to a protected machine using either of two methods:
- As part of protecting a machine. When using this method, you can apply encryption to one or multiple machines simultaneously. This method lets you add a new encryption key, or apply an existing key to the selected machine or machines.
To use encryption when first defining protection for a machine, you must select the advanced options in the relevant Protect Machines Wizard. This selection adds an Encryption page to the wizard workflow. From this page, select Enable encryption, and then select an existing encryption key or specify parameters for a new key. For more information, see Protecting a machine or About protecting multiple machines, respectively.
- By modifying the configuration settings for a machine. This method applies an encryption key to one protected machine at a time. There are two approaches for modifying configuration settings for a machine in the Rapid Recovery Core:
- Modify the configuration settings for a specific protected machine. The encryption key you want to use for this approach must already exist on the Rapid Recovery Core, be a universal key type, and must be in an unlocked state. Encryption is part of the General settings. For more information, see Viewing and modifying protected machine settings.
- Click the
Not Encrypted icon on the Protected Machines page. Using this approach you can create and apply a new encryption key, or assign an existing unlocked universal key to the specified protected machine. For more information, see Applying an encryption key from the Protected Machines page.
Applying an encryption key from the Protected Machines page
Once an encryption key has been added to aRapid Recovery Core, it can be used for any number of protected machines.
If you select an encryption key during the initial protection of one or more machines, that key is automatically applied to any machines you protect using that wizard. In such cases, this procedure is not required.
Perform this procedure:
- If you want to apply an existing, universal, unlocked encryption key to any protected machine in your Core.
- If you just added a new encryption key using the process described in the topic Adding an encryption key and want to apply that key to a protected machine.
- If encryption is already applied to a protected machine in your Core, but you want to change the key to a different universal, unlocked key available in your Core.
|
|
Caution: After you apply an encryption key to a protected machine, Rapid Recovery takes a new base image for that machine upon the next scheduled or forced snapshot. |
- Navigate to the Rapid Recovery Core Console and click Protected Machines.
The Protected Machines page appears, listing all the machines protected by this Core. An open lock
indicates that a protected machine has encryption applied.
- In the Protected Machines pane, click the lock icon for the protected machine you want to configure.
The Encryption Configuration dialog box appears.
- Do one of the following:
- If you want to apply an existing encryption key to this machine, select Encrypt data using Core-based encryption with an existing key, and from the drop-down menu, select the appropriate key. Click OK to confirm.
- If you want to change an existing encryption key to a different universal, unlocked key, select Encrypt data using Core-based encryption with a new key, and from the drop-down menu, select the appropriate key. Click OK to confirm.
- If you want to create a new encryption key and apply it to this protected machine, select Encrypt data using Core-based encryption with a new key. Then enter the details for the key as described in the following table.
Table 38: New encryption key details Text Box Description Name Enter a name for the encryption key. Encryption key names must contain between 1 and 64 alphanumeric characters. Do not use prohibited characters or prohibited phrases.
Description Enter a descriptive comment for the encryption key. This information appears in the Description field when viewing a list of encryption keys in the Rapid Recovery Core Console. Descriptions may contain up to 254 characters. Best practice is to avoid using prohibited characters and prohibited phrases.
Passphrase Enter a passphrase used to control access. Best practice is to avoid using prohibited characters.
Record the passphrase in a secure location. Quest Data Protection Support cannot recover a passphrase. Once you create an encryption key and apply it to one or more protected machines, you cannot recover data if you lose the passphrase.
Confirm Passphrase Re-enter the passphrase. It is used to confirm the passphrase entry.
- Click OK.
The dialog box closes. The encryption key you specified has been applied to future backups for this protected machine, and the lock now appears as closed.
Optionally, if you want the encryption key applied immediately, force a snapshot. For more information, see Forcing a snapshot.
Caution: Rapid Recovery uses AES 256-bit encryption in the Cipher Block Chaining (CBC) mode with 256-bit keys. While using encryption is optional, Quest recommends that you establish an encryption key, and that you protect the passphrase you define. Store the passphrase in a secure location as it is critical for data recovery. Without a passphrase, data recovery is not possible.