Chat now with support
Chat mit Support

DR Series Software 4.0.3 - Command Line Reference Guide

Introduction to the DR Series System Command Line Reference Guide Introducing the DR Series system Managing the DR Series system
Alerts Commands Authenticate Commands Network
Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help
OST RDA Stats Storage Group commands System
System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --hybrid_replication [--enable][--disable][--status] system --rdairgap [--enable][--disable][--set_retention_period <0 days to 365 days>][--get_retention_period][--open][--close][--status] system --rdairgap_schedule [--start_time <HH:MM>][--end_time <HH:MM>][--remove] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --help
User Virtual Machine
Maintaining the DR Series System
Diagnostics Maintenance
Maintenance Command Usage maintenance --filesystem [--start_scan [verify_data | verify_rda_metadata | verify_metadata] [--storage_group <name>] maintenance --filesystem [--stop_scan] maintenance --filesystem [--scan_status] maintenance --filesystem [--scan_report [verbose]] maintenance --filesystem [--repair_status [verbose]] maintenance --filesystem [--repair_history [verbose]] maintenance --filesystem [--scan_restart [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--repair_now] maintenance --filesystem [--reclaim_space] maintenance --filesystem [--clear_quarantine] maintenance --filesystem [--clear_quarantine] maintenance --filesystem --show_throughput maintenance --configuration [--backup] maintenance --configuration [--restore] maintenance --configuration [--reinit_dictionary] maintenance --configuration [--reset_web_certificate] maintenance --configuration --enable_sha256_web_certificate maintenance --hardware [--reinit_nvram] maintenance --hardware [--restore_hw_db] maintenance --hardware [--motherboard_replaced] maintenance --disk [--make_standby [slot num]] [--type <internal | external-<num> | service tag>] --clear_foreign] maintenance --remote_access [--show] maintenance --remote_access [--enable] maintenance --remote_access [--racreset] maintenance --remote_access [--static_ip] [--ip <IPv4/IPv6 address>] [--netmask <netmask>] [--gateway <IPv4/IPv6 address>] [--device <lom1|lom2|lom3|lom4>] maintenance --remote access [--disable] maintenance --vdisk --check_consistency --type <boot|internal|external> [--service_tag <service tag>] maintenance --help
Managing DR Series System Storage Operations
System Storage Operation Commands Connection Container VTL NDMP iSCSI FC Replication Seed Schedule
Data Integrity Checking Additional Linux Commands About us

network --traceroute --destination <ip address | hostname>

Description

Performs a trace route for packets that were sent to a DR Series system.

Syntax

network --traceroute --destination 10.25.20.20

Result

traceroute to 10.15.10.21 (10.15.10.21), 30 hops max, 40 byte packets
1 10.25.24.1 (10.25.24.1) 0.510 ms 0.654 ms 0.673 ms
2 10.20.12.16 (10.20.12.16) 7.095 ms 7.564 ms 7.843 ms
3 10.16.16.2 (10.16.16.2) 1.092 ms 1.097 ms 1.130 ms
4 10.16.0.9 (10.16.0.9) 1.006 ms 0.980 ms 1.017 ms
5 10.18.14.97) 6.864 ms 5.703 ms 6.264 ms
6 10.13.19.5) 7.230 ms 7.230 ms 7.260 ms
7 10.16.19.6) 8.540 ms 8.624 ms 8.848 ms
8 10.15.15.11 (10.15.15.11) 8.772 ms 9.032 ms 8.859 ms
9 10.18.15.18 (10.158.15.18) 10.540 ms 10.674 ms 10.285 ms
10 10.15.0.21 (10.15.0.21) 9.153 ms 9.051 ms 9.216 ms

network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>]

Description

Pings any target DR Series system by sending five ICMP ECHO_REQUEST packets to the specified destination to verify that it can be reached. The interface option is only available on a Physical DR.

Syntax

network --ping --destination 10.25.19.5

Result

PING 10.25.19.5 (10.25.19.5) from 10.20.14.15 bond0: 56(84) bytes of data.

64 bytes from 10.25.19.5: icmp_seq=1 ttl=64 time=0.039 ms
64 bytes from 10.25.19.5: icmp_seq=2 ttl=64 time=0.049 ms
64 bytes from 10.25.19.5: icmp_seq=3 ttl=64 time=0.041 ms
64 bytes from 10.25.19.5: icmp_seq=4 ttl=64 time=0.041 ms
64 bytes from 10.25.19.5: icmp_seq=5 ttl=64 time=0.049 ms

--- 10.25.19.5 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 3999ms
rtt min/avg/max/mdev = 0.039/0.043/0.049/0.009 ms

Other Command Options

--tries

Specify the number of ping attempts by entering a value using the DR Series system CLI --tries command option.

Example

network --ping --destination 10.25.19.5 --tries 3

PING 10.25.19.5 (10.25.19.5) from 10.20.14.15 bond0: 56(84) bytes of data.

64 bytes from 10.25.19.5: icmp_seq=1 ttl=64 time=0.032 ms
64 bytes from 10.25.19.5: icmp_seq=2 ttl=64 time=0.049 ms
64 bytes from 10.25.19.5: icmp_seq=3 ttl=64 time=0.047 ms

--- 10.25.19.5 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 5999ms
rtt min/avg/max/mdev = 0.032/0.043/0.049/0.005 ms

--size

Specify a desired ping packet size by entering a value using the DR Series system CLI --size command option.

Example

network --ping --destination system-69 --size 35

PING 10.20.19.20 (10.20.19.20) from myDR4000 bond0: 35(63) bytes of data.

43 bytes from 10.20.19.20: icmp_seq=1 ttl=64 time=0.129 ms
43 bytes from 10.20.19.20): icmp_seq=2 ttl=64 time=0.163 ms
43 bytes from 10.20.19.20: icmp_seq=3 ttl=64 time=0.166 ms
43 bytes from 10.20.19.20: icmp_seq=4 ttl=64 time=0.237 ms
43 bytes from 10.20.19.20: icmp_seq=5 ttl=64 time=0.179 ms

--- 10.20.19.20.acme.local ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4000ms
rtt min/avg/max/mdev = 0.129/0.174/0.237/0.038 ms

--interface

Specify an interface address to use as the source address by entering a value using the DR Series system CLI --interface command option.

Example

network --ping --destination system-69 --interface bond0

network --blink

Description

The command blinks the LED on the specific ethernet device.

Syntax

network --blink --nwif <ethN> --time <N>

--nwif Eth interface to blink.
--time Blink duration time in seconds (default 10, max 300).

For example, to blink the LED for eth3, run the command: network --blink --nwif eth3 --time 30

Result

Check the LED on the ethernet card on the back of the system for identification.

network --enable

Description

The command starts the specific ethernet device(s) on restart.

Syntax

network --enable [--bondif <bond0,bond1,...,bondN>]
[--nwif <eth0,eth1,...,ethN>]


--bondif Bond interface(s) to delete.
--nwif Eth interface(s) to dele

For example, to enable eth2, run the command: network --enable --nwif eth2

Result

Interface device operation successful. Please restart networking for the changes to take effect.
Verwandte Dokumente

The document was helpful.

Bewertung auswählen

I easily found the information I needed.

Bewertung auswählen