Chat now with support
Chat mit Support

NetVault 11.4.5 - Administration Guide

Introduction Getting started Configuring clients Configuring storage devices Backing up data Managing policies Restoring data Managing jobs Monitoring logs Managing storage devices
Monitoring device activity Managing disk-based storage devices in table view Managing disk-based storage devices in tree view Managing tape libraries in table view Managing tape libraries in tree view Managing tape drives in table view Managing tape drives in tree view Adding shared devices
Managing storage media Managing user accounts Monitoring events and configuring notifications Reporting in NetVault Backup Working with client clusters Configuring default settings for NetVault Backup
About configuring default settings Configuring encryption settings Configuring plug-in options Configuring default settings for post-scripts Configuring default settings for Verify Plug-in Configuring Deployment Manager Settings Configuring Job Manager settings Configuring Logging Daemon settings Configuring Media Manager settings Configuring Network Manager settings Configuring Process Manager settings Configuring RAS device settings Configuring Schedule Manager settings Configuring Web Service settings Configuring Auditor Daemon settings Configuring firewall settings Configuring general settings Configuring security settings Synchronizing NetVault Time Configuring default settings for global notification methods Configuring the reporting utility Configuring NetVault Backup to use a specific VSS provider Configuring default settings using Txtconfig
Diagnostic tracing Managing diagnostic data Using the deviceconfig utility NetVault Backup processes Environment variables Network ports used by NetVault Backup Troubleshooting

Configuring default settings for tape drives

1
Start a terminal session or command window, and navigate to the “bin” directory under the NetVault Backup installation directory.

-servername

Specifies the FQDN, or IP Address of the NetVault Backup Server.

With this option, you must specify either the HTTP or HTTPS port to connect to the remote Web Service.

If you omit this option, the local server is used. The deviceconfig utility connects to the local Web Service and automatically detects the local Web Service configuration.

-httpport

Specifies the HTTP port for Web Service. This option is only required if the server name is supplied.

-httpsport

Specifies the HTTPS port for Web Service. This option is only required if the server name is supplied.

-username

Specifies a valid NetVault Backup user name.

-password

Specifies the password for the user account.

-drivemachine

Specifies the name of the NetVault Backup machine to which the drive is attached.

-drivepath

Specifies the name or path of the drive.

3
The deviceconfig utility displays the Drive Configuration screen. You can access the configuration settings by pressing the corresponding option number. The available setting types include the following:
NDMP Configuration: To configure NDMP Settings, select this option. For more information about these settings, see NDMP settings.
Configuration: To configure general settings for a tape drive, select this option. For more information about these settings, see General settings for tape drives.
Software Compression: To configure software compression settings, select this option. For more information about these settings, see Software compression settings.
Performance: To configure drive performance settings, select this option. For more information about these settings, see Drive performance settings.
Statistics: To configure statistics collection settings, select this option. For more information about these settings, see Statistics collection settings.
Generic Cleaning: To configure generic cleaning settings for a tape drive, select this option. For more information about these settings, see Generic cleaning settings.

NDMP settings

On the NDMP Configuration screen, the following settings are available.

Table 139. NDMP settings

Allow Mover to do Local Data Transfer if Possible

The default setting is OFF. To change it, press the option number.

Allow Mover to do IPC Data Transfers if Possible

The default setting is OFF. To change it, press the option number.

Allow Mover to do TCP Data Transfer if Possible

The default setting is ON. To change it, press the option number.

Allow Mover to do Direct Backup if Possible

The default setting is ON. To change it, press the option number.

Allow Mover to do Direct Restore if Possible

The default setting is ON. To change it, press the option number.

Emulate NDMP Device

The default setting is ON. To change it, press the option number.

General settings for tape drives

On the Configuration screen, the following settings are available.

Device Serial Number

Displays the drive serial number.

End of media warning

This option specifies the amount of media reserved at the end of the tape at which the “end of media” warnings are issued. This value is specified in MB. The default value is 0MB.

Time between polling empty drive

This option specifies the interval at which NetVault Backup polls a standalone drive to detect a tape in the device. This value is specified in number of minutes. The default value is one (1).

To turn off polling, set this option to zero (0).

Media block size (KiB)

This option specifies the block size used for read and write operations. The default value is 64KiB.

You can change the media block size in increments of 1KiB, but many devices may only accept a value in the multiples of 4KiB or 32KiB.

Increasing the block size can reduce the number of times a backup needs to read data and write it to media. However, large media block sizes do not always imply an overall faster backup. The maximum block size is limited by several factors, such as the OS, SCSI adapter, drive make, drive model, and drive type.

On Linux and UNIX systems, you can increase the media block size for optimum performance.

On Windows, you might be required to change the registry setting MaximumSGList to use block sizes larger than 64KB. Before changing this setting, check that the SCSI bus is only used by the tape devices. If other devices also use the SCSI bus, this registry change might prevent them from working. If you want to apply these changes only to a specific channel on the HBA, consult the hardware vendor.

To change the registry setting on Windows, follow these steps:

2
Open the key [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\ Services\<HBA Vendor>\Parameters (where <HBA Name> is specific to your SCSI card — for example, QL2200 for a Qlogic 2200 card).
3
Create the Parameters key if not present.
4
Under Parameters, create the Device key if not present.
5
Under the Device key, add the DWORD registry value MaximumSGList if not present.

Time to wait for plugin to connect

This option specifies the timeout period for the plug-in to connect to NetVault Backup. The job is aborted if connection cannot be established within the specified interval. This value is specified in number of seconds. The default value is zero (0). With the default setting, the job is not timed out.

Supports Short Reads

The default setting is ON. To change it, press the option number.

Cleaning Tapes Supported

This option indicates whether the library supports cleaning tapes or not. The default value is usually correct, unless certain library models have a different setting.

Compression

This option allows you to use a tape drive’s built-in compression feature. Not all tape drives support hardware-based data compression. The compression ratio varies depending on the type of data and the compression algorithm that the drive uses. Consult the hardware documentation to determine the compression ratios for the drive.

Software compression settings

On the Software Compression screen, the following settings are available. The software compression settings only apply to virtual tape drives.

Perform software data compression

The default setting is OFF. To perform software compression, change the setting to ON. The data is compressed when it is transferred to the device during backup.

Compression decision switch

The value set for this option determines the minimum level of compression that must be achieved when data is compressed during a backup. For example, if you set the value to 80 percent, one of the following occurs:

If you specify 80 percent, a file size of a 100MB must be <= 80MB after compression. If the specified level is not achieved, NetVault Backup backs up the file in its uncompressed form. The extent that data can be compressed depends on the data contents. Encrypted data cannot be compressed. With some files, compression may actually result in a file that is larger than the original uncompressed file.

Number of data blocks per compression unit

Type the number of data blocks per compression unit. The default block size is 8KiB.

Verwandte Dokumente

The document was helpful.

Bewertung auswählen

I easily found the information I needed.

Bewertung auswählen