立即与支持人员聊天
与支持团队交流

NetVault Plug-in for VMware 10.0.5 - User Guide

Introduction Installing the plug-in Configuring the plug-in Defining a backup strategy Using the image-level backup method Using the file-level backup method Restoring image-level backups Restoring file-level backups Troubleshooting

Configuring the plug-in

•
Adding a server
•
Configuring default settings
•
Configuring CBT
•
Enabling virtual machine locking
•
Understanding backup consistency states

Adding a server

Before you can start using the plug-in for backups and restores, you must add the applicable ESX/ESXi and vCenter Servers to the plug-in, and configure a user account to log on to the server.
•
Standalone ESX/ESXi Server setup: In a VMware environment consisting of one or more ESX or ESXi Servers, add the individual hosts to the plug-in, and configure a user account for each server.
•
Cluster setup: In a cluster setup managed by a vCenter Server, add the vCenter Server to the plug-in, and configure a user account for this server.
 
 
*NOTE: The Plug‑in for VMware supports an ESXi Server that is in Lockdown mode if the host is managed by a vCenter Server.
To add a server
1
In the Navigation pane, click Create Backup Job.
— or —
In the Navigation pane, click Guided Configuration, and then on the NetVault Configuration Wizard page, click Create Backup Jobs.
2
Click Create New next to the Selections list to open the NetVault Backup Selections page.
3
Open the NetVault Backup Client on which the plug-in is installed. Select VMware Plugin, and in the Actions list, click Add Server.
4
Configure the following settings.
 
Table 1. Add Server
Option
Description
Server Name
In a standalone server setup, type a name for the ESX or ESXi Server.
In a cluster setup, type a name for the vCenter Server.
The server name must be unique. If you do not provide a name, the plug-in uses the Server Address as the server name.
NOTE: You cannot change the server name once it is configured.
 
NOTE: When adding an ESX/ESXi or a vCenter Server to the plug-in installed on different clients, specify the same server name on all clients. If you use different names, the plug-in reports an error (“Server not found”) when you try to restore a virtual machine backed up from one server to the same server with a different name because the restore path is different.
Server Address
In a standalone server setup, type the Fully Qualified Domain Name (FQDN) of the ESX or ESXi Server.
In a cluster setup, type the FQDN of the vCenter Server.
You can also specify the IP address of the server, but using the FQDN is the preferred method.
User
Specify a user account that can be used to log on to the configured server. The user account must have privileges to register or create virtual machines.
Password
Type the password for the user account.
5
Click OK to close the dialog box.
The plug-in tries to log on to the server, and if successful, adds the server to the backup selection tree.

Reconfiguring a server

To reconfigure an existing server
1
Start the Backup Job Wizard, and click Create New next to the Selections list.
2
Open the NetVault Backup Server, and then open VMware Plugin,
3
Select the ESX/ESXi or vCenter Server, and in the Actions list, click Edit Server.
4
Reconfigure the applicable settings. For more information about these settings, see Add Server. In the Edit Server dialog box, the server name is displayed as a read-only setting.
5
Click OK to save the new settings.

Removing a server

To remove a server
1
Start the Backup Job Wizard, and click Create New next to the Selections list.
2
Open the NetVault Backup Server, and then open VMware Plugin.
3
Select the ESX/ESXi or vCenter Server, and in the Actions list, click Remove Server.
4
In the confirmation dialog box, click OK.
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级