立即与支持人员聊天
与支持团队交流

DR Series Software 3.2.6 - Command Line Reference Guide

Notes, cautions, and warnings *** Introduction to the DR Series System Command Line Reference Guide Introducing the DR Series System Managing the DR Series System
Alerts Commands Authenticate Commands Network
Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --disable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|NDMP|ISCSI|RDS>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help
OST RDA Stats System
System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setcompression [--fast] [--balanced] [--best] system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --marker [--disable] system --marker [--enable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --storage [--extend] system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --encryption --show system --encryption --passphrase system --encryption [--mode <static|internal>] [--interval <7 days to 70 years>] system --encryption [--set <ON|OFF>] system --help
User Virtual Machine
Maintaining the DR Series System
Diagnostics Maintenance
Maintenance Command Usage maintenance --filesystem [--start_scan [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--stop_scan] maintenance --filesystem [--scan_status] maintenance --filesystem [--scan_report [verbose]] maintenance --filesystem [--repair_status [verbose]] maintenance --filesystem [--repair_history [verbose]] maintenance --filesystem [--scan_restart [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--repair_now] maintenance --filesystem [--reclaim_space] maintenance --filesystem [--stop_reclaim_space] maintenance --filesystem [--clear_quarantine] maintenance --filesystem --show_throughput maintenance --configuration [--backup] maintenance --configuration [--restore] maintenance --configuration [--reinit_dictionary] maintenance --configuration [--reset_web_certificate] maintenance --hardware [--reinit_nvram] maintenance --hardware [--restore_hw_db] maintenance --hardware [--motherboard_replaced] maintenance --disk [--make_standby [slot num]] [--type <internal | external-<num> | service tag>] --clear_foreign] maintenance --remote_access [--show] maintenance --remote_access [--enable] maintenance --remote_access [--racreset] maintenance --remote_access [--static_ip] [--ip <IPv4/IPv6 address>] [--netmask <netmask>] [--gateway <IPv4/IPv6 address>] [--device <lom1|lom2|lom3|lom4>] maintenance --remote access [--disable] maintenance --vdisk --check_consistency --type <boot|internal|external> [--service_tag <service tag>] maintenance --help
Managing DR Series System Storage Operations
System Storage Operation Commands Connection Container VTL NDMP ISCSI Replication Seed Schedule
Data Integrity Checking Additional Linux Commands

network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>]

Syntax

network --ping --destination 10.25.19.5

Result

PING 10.25.19.5 (10.25.19.5) from 10.20.14.15 bond0: 56(84) bytes of data.

64 bytes from 10.25.19.5: icmp_seq=1 ttl=64 time=0.039 ms
64 bytes from 10.25.19.5: icmp_seq=2 ttl=64 time=0.049 ms
64 bytes from 10.25.19.5: icmp_seq=3 ttl=64 time=0.041 ms
64 bytes from 10.25.19.5: icmp_seq=4 ttl=64 time=0.041 ms
64 bytes from 10.25.19.5: icmp_seq=5 ttl=64 time=0.049 ms

--- 10.25.19.5 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 3999ms
rtt min/avg/max/mdev = 0.039/0.043/0.049/0.009 ms

Other Command Options

--tries

Specify the number of ping attempts by entering a value using the DR Series system CLI --tries command option.

Example 

network --ping --destination 10.25.19.5 --tries 3

PING 10.25.19.5 (10.25.19.5) from 10.20.14.15 bond0: 56(84) bytes of data.

64 bytes from 10.25.19.5: icmp_seq=1 ttl=64 time=0.032 ms
64 bytes from 10.25.19.5: icmp_seq=2 ttl=64 time=0.049 ms
64 bytes from 10.25.19.5: icmp_seq=3 ttl=64 time=0.047 ms

--- 10.25.19.5 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 5999ms
rtt min/avg/max/mdev = 0.032/0.043/0.049/0.005 ms

--size

Specify a desired ping packet size by entering a value using the DR Series system CLI --size command option.

Example

network --ping --destination system-69 --size 35

PING 10.20.19.20 (10.20.19.20) from myDR4000 bond0: 35(63) bytes of data.

43 bytes from 10.20.19.20: icmp_seq=1 ttl=64 time=0.129 ms
43 bytes from 10.20.19.20): icmp_seq=2 ttl=64 time=0.163 ms
43 bytes from 10.20.19.20: icmp_seq=3 ttl=64 time=0.166 ms
43 bytes from 10.20.19.20: icmp_seq=4 ttl=64 time=0.237 ms
43 bytes from 10.20.19.20: icmp_seq=5 ttl=64 time=0.179 ms

--- 10.20.19.20.acme.local ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4000ms
rtt min/avg/max/mdev = 0.129/0.174/0.237/0.038 ms

--interface

Specify an interface address to use as the source address by entering a value using the DR Series system CLI --interface command option.

Example

network --ping --destination system-69 --interface bond0
Parent topic: Network

network --blink

Syntax

 network --blink --nwif <ethN> --time <N>

		 --nwif   Eth interface to blink.
		 --time   Blink duration time in seconds (default 10, max 300).

For example, to blink the LED for eth3, run the command: network --blink --nwif eth3 --time 30

Result

Check the LED on the ethernet card on the back of the system for identification.
Parent topic: Network

network --enable

Syntax

 network --enable [--bondif <bond0,bond1,...,bondN>]
        	[--nwif <eth0,eth1,...,ethN>]


       		--bondif   Bond interface(s) to delete.
        	--nwif     Eth interface(s) to dele

For example, to enable eth2, run the command: network --enable --nwif eth2

Result

Interface device operation successful. Please restart networking for the changes to take effect.
Parent topic: Network

network --disable

Syntax

 network --disable [--bondif <bond0,bond1,...,bondN>]
        	[--nwif <eth0,eth1,...,ethN>]


       		--bondif   Bond interface(s) to delete.
        	--nwif     Eth interface(s) to dele
Note: You cannot disable eth interfaces which are part of a bond.

For example, to disable eth2, run the command: network --disable --nwif eth2

Result

Interface device operation successful. Please restart networking for the changes to take effect.
Parent topic: Network
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级