立即与支持人员聊天
与支持团队交流

DR Series Software 3.2.6 - Command Line Reference Guide

Notes, cautions, and warnings *** Introduction to the DR Series System Command Line Reference Guide Introducing the DR Series System Managing the DR Series System
Alerts Commands Authenticate Commands Network
Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --disable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|NDMP|ISCSI|RDS>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help
OST RDA Stats System
System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setcompression [--fast] [--balanced] [--best] system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --marker [--disable] system --marker [--enable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --storage [--extend] system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --encryption --show system --encryption --passphrase system --encryption [--mode <static|internal>] [--interval <7 days to 70 years>] system --encryption [--set <ON|OFF>] system --help
User Virtual Machine
Maintaining the DR Series System
Diagnostics Maintenance
Maintenance Command Usage maintenance --filesystem [--start_scan [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--stop_scan] maintenance --filesystem [--scan_status] maintenance --filesystem [--scan_report [verbose]] maintenance --filesystem [--repair_status [verbose]] maintenance --filesystem [--repair_history [verbose]] maintenance --filesystem [--scan_restart [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--repair_now] maintenance --filesystem [--reclaim_space] maintenance --filesystem [--stop_reclaim_space] maintenance --filesystem [--clear_quarantine] maintenance --filesystem --show_throughput maintenance --configuration [--backup] maintenance --configuration [--restore] maintenance --configuration [--reinit_dictionary] maintenance --configuration [--reset_web_certificate] maintenance --hardware [--reinit_nvram] maintenance --hardware [--restore_hw_db] maintenance --hardware [--motherboard_replaced] maintenance --disk [--make_standby [slot num]] [--type <internal | external-<num> | service tag>] --clear_foreign] maintenance --remote_access [--show] maintenance --remote_access [--enable] maintenance --remote_access [--racreset] maintenance --remote_access [--static_ip] [--ip <IPv4/IPv6 address>] [--netmask <netmask>] [--gateway <IPv4/IPv6 address>] [--device <lom1|lom2|lom3|lom4>] maintenance --remote access [--disable] maintenance --vdisk --check_consistency --type <boot|internal|external> [--service_tag <service tag>] maintenance --help
Managing DR Series System Storage Operations
System Storage Operation Commands Connection Container VTL NDMP ISCSI Replication Seed Schedule
Data Integrity Checking Additional Linux Commands

system --storage [--extend]

Syntax

system --storage --extend

Result

# system --storage --extend


WARNING: IO to the box will be stopped during this operation.


Do you want to continue (yes/no) [n]? yes

Please enter the root password:


Stopping filesystem... Done.

Expanding data storage volume... Done.

Starting filesystem... Done.

Data storage expanded successfully.

system --mgmt_traffic

Syntax

system --mgmt_traffic [--add] [--type <Webserver|Telnet>] [--interface <bondN|ethN|lo>]
                 [--update] [--type <Webserver|Telnet>] [--interface <bondN|ethN|lo>]
                 [--delete] [--type <Webserver|Telnet>]


        --add         Add access network configuration.
        --update      Update access network configuration.
        --delete      Delete access network configuration.
        --type        Access type <Webserver|Telnet> to configure.
        --interface   Interface to use for access [bond(0-N)|eth(0-N)].

Result

Successfully added application webserver.
Restarting webserver service ... done.

system --backup_traffic

Syntax

system --backup_traffic [--add] [--type @NFS|CIFS|OST|NDMP|ISCSI|RDS] [--interface @bond(0-N)|eth(0-N)|lo#]
                 [--update] [--type @NFS|CIFS|OST|NDMP|ISCSI|RDS] [--interface @bond(0-N)|eth(0-N)|lo#]
                 [--delete] [--type @NFS|CIFS|OST|NDMP|ISCSI|RDS]


        --add         Add backup network configuration.
        --update      Update backup traffic network configuration.
        --delete      Delete backup traffic network configuration.
        --type        Backup traffic type [NFS|CIFS|OST|NDMP|ISCSI|RDS] to configure.
        --interface   Interface to use for backup traffic.

Result

WARNING: This operation requires filesystem server restart. IO to the box will be stopped.
Do you want to continue (yes/no) [n]? y
Successfully added application.
Restarting file system ... done.

system --replication_traffic

Syntax

system --replication_traffic [--add] [--interface <bondN|ethN|lo>]
                 [--update] [--interface <bondN|ethN|lo>]
                 [--delete]


        --add         Add default replication network configuration.
        --update      Update default replication network configuration.
        --delete      Delete default replication network configuration.
        --interface   Interface to use for replicating 'source' data.
For example, to add the replication, run the command, system --replication_traffic --add --interface bond0

Result

Successfully added application replication.
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级