Rapid Recovery protects your data on Windows and Linux machines. Backups of protected machines are saved to the repository associated with your Rapid Recovery Core as recovery points. From these recovery points, you can restore your data using one of the following methods.
- From the Rapid Recovery Core Console, you can restore entire volumes from a recovery point of a non-system volume, replacing the volumes on the destination machine. This process uses the Restore Machine Wizard. For more information, see About restoring volumes from a recovery point.
- You can also restore entire volumes on Linux machines from recovery points using the command line from the protected Linux machine. For more information on using the command line local_mount utility, see Restoring volumes for a Linux machine using the command line.
When restoring data for agentlessly protected machines only, the Volume Mapping page of the Restore Machine Wizard includes the option Restore all configuration data. This option is associated with the VM configuration and restore feature. For more information, see VMware VM configuration backup and restore.
You cannot restore a volume that contains the operating system directly from a recovery point, because the machine to which you are restoring is using the operating system and drivers that are included in the restore process. If you want to restore from a recovery point to a system volume (for example, the C drive of the protected machine), you must perform a Bare Metal Restore (BMR). This involves creating a bootable image from the recovery point, which includes operating system and configuration files as well as data. You then start the target machine from that bootable image to complete the restore. The boot image differs if the machine you want to restore uses a Windows operating system or a Linux operating system. If you want to restore from a recovery point to a system volume on a Windows machine, see Performing a bare metal restore using the Restore Machine Wizard. If you want to restore from a recovery point of a system volume on a Linux machine, see Performing a bare metal restore for Linux machines.
If you have a software RAID on a Linux machine protected by Rapid Recovery Agent release 6.2 or later, you can restore the software RAID from a recovery point.
|
|
NOTE: Since this feature was introduced in release 6.2, it is not compatible for snapshots taken on earlier Agent versions. If you upgrade Rapid Recovery Agent to release 6.2 or later and then capture snapshots in your Rapid Recovery Core, you will be able to restore the software RAID from the new snapshots. |
Finally, in contrast to restoring entire volumes, you can mount a recovery point from a Windows machine, and browse through individual folders and files to recover only a specific set of files. For more information, see Restoring a directory or file using Windows Explorer. If you need to perform this while preserving original file permissions (for example, when restoring a user’s folder on a file server), see Restoring a directory or file and preserving permissions using Windows Explorer.
The topics in this section describe information about restoring data on physical machines. For more information on exporting protected data from a recovery point to a virtual machine, see VM export.
|
|
NOTE: When recovering data on Windows machines, if the volume that you are restoring has Windows data deduplication enabled, you will need to make sure that deduplication is also enabled on the Core server.
|
This section describes how to restore data from recovery points saved to your repository using Rapid Recovery Core.
Topics include:
The Rapid Recovery file search and restore feature lets you find one or more files in the recovery points of a protected machine. You can then restore one or more of the results to a local disk.
Searching guidelines
On the File Search page of the Core Console, you can search for a file from a set of recovery points from the machine that you select. The search criteria are divided into two groups: basic and advanced.
The basic group includes the following parameters:
- The protected machine whose recovery points you want to search.
- A time range that limits the search to only recovery points that were created between the start time and end time.
- The name or mask of the file that you want to find. You can use the "?" wildcard to replace any single character and the "*" to replace zero or multiple characters; however, more specific filenames produce more specific results.
- A list of paths to directories in which to search.
|
|
NOTE: All basic criteria is required. If no directory is provided, Rapid Recovery searches all volumes of the specified protected machine. |
The More Options button reveals the advanced group, which includes the following parameters:
- The option to search recursively in subdirectories of the search location or only in the specified location.
- The ability to run an algorithm that increases the speed of searches on NTFS volumes.
- The ability to limit the number of search results to a more manageable sum.
|
|
NOTE: Specific search criteria produce faster and more accurate your search results. Including subdirectories (for example, C:\work\documents\accounting instead of C:) reduces the amount of time it takes to complete the search, as does providing restrictive file masks (for example, invoice*.pdf instead of in*.*). |
Because the feature continues to search through recovery points and locations even after the requested file is found, you can pause or stop a search before it completes. You can run multiple searches can simultaneously, but you cannot begin them at the same time. For example, to find another file, you can begin a second search while the first search is still in progress. However, you can only search one protected machine at a time.
|
|
NOTE: In the previous example, pausing the first search makes more memory available for the second search, which helps the second search finish faster. Running multiple searches at one time is memory intensive and increases the amount of time it takes to complete a search. |
Each search appears as a tab on the page. When you are finished searching, you can close the tabs individually or all at once.
Restoring guidelines
After you find the file, you can restore it directly from the File Search page.
The file search and restore feature limits restoring capabilities to only locations on the Core. You cannot restore a file to a protected machine.
When you want to restore a file instead of a volume, you can use Rapid Recovery to find that file among the recovery points for your protected machine. Search criteria, such as date range and directory, let you narrow the search to a small group of relevant recovery points.
|
|
NOTE: Specific search criteria produce faster and more accurate your search results, and consume less memory. Including subdirectories (for example, C:\work\documents\accounting instead of C:) reduces the amount of time it takes to complete the search, as does providing restrictive file masks (for example, invoice*.pdf instead of in*.*). |
After you find the file, you can then restore it directly from the list of search results.
- From the Rapid Recovery Core Console icon bar, click the
More drop-down menu, and select 
File Search.
The File Search page opens.
- On the File Search page, to search for a file within the recovery points of a specific protected machine, complete the information described in the following table.
Table 136: File search criteria
|
Machine
|
Select the protected machine that you want to search from the drop-down list.
|
|
NOTE: You can search through the recovery points of only one protected machine at a time. | |
|
Recovery points date range
|
Specify the date and time of the oldest recovery point and the newest recovery point that you want to search. Only the recovery points created within this span of time are searched.
|
|
NOTE: The default time span is the previous month. For example, if conducting the search on August 22, 2018 at 2:04 PM, the default date range is 7/22/2018 2:04 PM to 8/22/2018 2:04 PM. | |
|
Filename (can use * and ? wildcards)
|
Enter the name of the file or a file mask for the file that you want to find and restore. Wildcards may be used as substitutes for unknown characters.
|
|
NOTE: You can use the "?" wildcard to replace any single character and the "*" wildcard to replace zero or multiple characters. | |
| Directories to search |
List one or more directories on the protected machine to limited the search to only those locations.
|
|
NOTE: If no directory is provided, Rapid Recovery searches all volumes of the specified protected machine. | |
- Optionally, click More Options, and then complete the information described in the following table.
Table 137: More file search options
| Include subdirectories |
Searches all the subdirectories of the directories listed in step 3. Enabled by default. |
|
Use fast search algorithm for NTFS volumes
|
Searches NTFS volumes without mounting them by parsing file system data structures, which is faster and consumes less memory while searching. Enabled by default.
|
|
NOTE: If you encounter an issue during a search of an NTFS volume, attempt the search again without this option selected. | |
| Limit search results to |
Enter the maximum number of results that you want to appear in the results. The default is 1000. |
- Click Start Search
The search begins. Each search appears as a tab under Search Results. You can use the buttons for each tab to pause or stop a search, or you can click the X on the tab to delete the search. Multiple searches can run simultaneously.
- From the search results, select the file that you want to restore.
- Click
![[Restore]](/ko-kr/technical-documents/image/6aa01701-544e-4930-b08f-9e8a05691bc7)
Restore.
The Restore Files dialog box opens.
- For Location, enter a destination path for the restored file on the machine on which the Core is installed and running.
- Click Restore.
The file you selected is restored to the specified destination path with the original directory tree in which the file appeared on the protected machine.
