지금 지원 담당자와 채팅
지원 담당자와 채팅

NetVault Plug-in for Hyper-V 12.2 - User Guide

Introducing NetVault Backup Plug-in for Hyper-V Installing or removing the plug-in Configuring the plug-in Backing up data Restoring data Troubleshooting

Restoring image-level backups

You can perform an image-level recovery, which restores the entire VM and establishes a new version of that VM in Hyper‑V Manager. The process restores files either to their original location or to a location specified by you when you create a selection set and enter information in the Rename/Relocate dialog box. For instructions on performing restores from a previous version of the plug-in, see the user's guide for the corresponding version.

 
* 
IMPORTANT: The plug-in flattens Hyper-V checkpoints when a backup is taken and later retrieved using an image-level recovery process. For example, if you back up a base disk that has two checkpoint files that the VM is running, the VM is restored with only one base disk; however, all content from the checkpoint files is included.

This process includes the steps outlined in the following topics:

•
Prerequisites for image-level restore
•
Configuring parallel streams
•
Selecting data for an image-level restore
•
Setting image-level restore options
•
Finalizing and submitting an image-level restore job

Prerequisites for image-level restore

Verify that the following prerequisites are met:

•
If you do not intend to use the Rename feature, Quest recommends that you delete the original VM before you perform recovery.
•
If you do not intend to use the Rename feature and you do not intend to delete the original VM, ensure that the VM is turned off. Also ensure that none of its files are open before you perform recovery. The plug-in’s recovery process overwrites the existing VM, and write-access is required.
•
Before recovering a VM to different host, verify that the VM resources in the Configuration File match the resources available on the host. In particular, verify that file locations and network-adapter names match. If they do not match, the VM might not get turned on. If resources are different on the target host, complete the recovery manually.
•
If you want to restore a backup created with NetVault Backup Plug‑in for Hyper‑V 12.0 or older to multiple VMs simultaneously, the backup job must have been configured to include this capability. For more information, see Configuring parallel streams.

Configuring parallel streams

When you restore a backup created with NetVault Backup Plug‑in for Hyper‑V 12.2 or later, the option to use or change the number parallel streams is available within the restore procedure, as found in Selecting data for an image-level restore. When you restore a backup created with an older version of the plug-in, if you want to use multiple parallel streams, then you must configure this setting before you can create a restore job.

Complete the following steps to configure parallel streams for versions 12.0 or older of NetVault Backup Plug‑in for Hyper‑V.

1
Start with one of the following options:
•
To configure parallel streams for a new backup job, in the Navigation pane, click Create Backup Job.You can also start the wizard from the Guided Configuration link. In the Navigation pane, click Guided Configuration. On the NetVault Configuration Wizard page, click Create backup jobs.
•
To configure parallel streams for an existing backup job, in the Navigation pane, click Manage Job Definitions, select the backup job for the respective Hyper-V host, and then click Edit Job.
2
Next to the Selections list, click Create New.
3
On the NetVault Backup Selections page, expand the Hyper-V host, click Hyper-V Plugin, and then click Configure.
4
In the Configure window, enter the maximum number of parallel streams that you want to apply to this Hyper-V host.
 
* 
NOTE: When saving to a tape drive, the number of parallel streams must be equal to or less than the number of tape drives from which you are restoring. Likewise, when using a RAS device, the number of parallel streams must be equal to or less than the number of VMs in the saveset.

The maximum streams allowed is 32.

5
Click OK.
There is no need to save the backup job to save the configuration. The change saves to the config file for the Hyper-V host and applies to all of its guest VMs.

Selecting data for an image-level restore

1
In the Navigation pane, click Create Restore Job.
2
On the Create Restore Job — Choose Saveset page, select Plug‑in for Hyper‑V from the Plugin Type list.
3
To filter the items displayed in the saveset table further, use the Client, Date, and Job ID lists.
The table displays the saveset name (job title and saveset ID), creation date and time, and size. By default, the list is sorted by creation date.
4
In the saveset table, select the applicable item.
When you select a saveset, the following details are displayed in the Saveset Information area: Job ID, job title, server name, client name, plug-in name, saveset date and time, retirement setting, Incremental Backup or not, Archive or not, and saveset size.
5
Click Next.
6
On the Create Selection Set page, if you want to restore more than one VM at a time, complete one of the following options:
•
For a 12.2 backup, click Edit Plugin Options, and then change the Maximum Number of Parallel Streams to the amount of VMs you want to simultaneously restore.
•
For a backup created with NetVault Backup Plug‑in for Hyper‑V 12.0 or older, see Configuring parallel streams.
 
* 
NOTE: When restoring multiple clusters, you can configure parallel streams for each cluster or each node.

If you do not want to restore using parallel streams, you can set the number of streams as 1.

7
Click OK.
8
On the Create Selection Set page, select the localhost or <clusterName> node to display the VMs, and then select one or more VMs to restore.
 
* 
NOTE: You cannot select individual files under a VM node. If you enabled indexing during backup and want to restore individual files, use file-level recovery. For more information, see Performing file-level recovery.

If you select an Incremental or Differential Backup, the plug-in automatically restores all savesets in the backup sequence up to the selected saveset.
관련 문서

The document was helpful.

평가 결과 선택

I easily found the information I needed.

평가 결과 선택