지금 지원 담당자와 채팅
지원 담당자와 채팅

Migrator Pro for Active Directory 20.11 - Requirements and Installation Guide

Section 1. Introduction Section 2. Directory Sync Pro Prerequisites Section 3. Directory Sync Pro for Active Directory Advanced Network Requirements Section 4. Migrator Pro for Active Directory Prerequisites Section 5. Requirements for Both Directory Sync Pro for Active Directory and Migrator Pro for Active Directory Section 6. Installing Directory Sync Pro for Active Directory and Migrator Pro for Active Directory Section 7. Upgrading Directory Sync Pro for Active Directory and Migrator Pro for Active Directory Section 8. Modifying, Repairing and Uninstalling Directory Sync Pro for Active Directory and Migrator Pro for Active Directory Section 9. Migrator Pro for Active Directory Agent Installation Section 10. Troubleshooting Appendix A: Configuring Directory Sync Pro for Active Directory in a Non-English Active Directory Environment Appendix B. Installing and Configuring SQL Server Reporting Services Appendix C. STIG Environments Appendix D. Deployment in FIPS Environment

4.2 Workstation and Member Server System Requirements

Supported Operating Systems

  • Windows 7 SP1

  • Windows 10

  • Windows 11

  • Windows Server 2012

  • Windows Server 2012 R2

  • Windows Server 2016

  • Windows Server 2019

  • Windows Server 2022

PowerShell Requirements

  • All client operating systems must have at least PowerShell 2.0 installed.

.NET Framework Requirements

  • All operating systems must have .NET Framework 4.5.2 or newer installed. This will appear as ".NET 4.5.2 Extended" in the add/remove programs list.

  • The “client” installation of the .NET Framework (before 4.5) is not sufficient and must be upgraded to the full .NET Framework.

4.3 Admin Agent Device Requirements

Operating System Requirements

  • 64-bit operating systems only

  • Windows PowerShell 4.0

  • WMF 4.0 support

Supported Operating Systems

  • Windows Server 2012 R2

  • Windows Server 2016

Additional Requirements

  • Port Requirement: 80, 443

  • Software Requirement: .NET Framework 4.5.2

  • PowerShell Active Directory Module (only required if you want to run PowerShell scripts against Active Directory).

4.4 Networking Requirements

Domain Controller Access

For most scenarios, Migrator Pro for Active Directory requires access to at least one read/write domain controller in each source and target Active Directory domain. For fault tolerance, at least two domain controllers in each source and target domain is recommended.

If SID History will be synchronized, any domain controller listed in the Target DCs tab within a Directory Sync Pro for Active Directory profile will require access to the domain controller holding the PDC Emulator Active Directory FSMO role in the source. Keep in mind that even if the domain controller holding the PDC Emulator Active Directory FSMO role is not listed in the Source DCs tab, any SID History migration attempts will require a DC in the target to communicate with the PDC Emulator domain controller. For this reason, it is a best practice to ensure that all domain controllers specified on the Target DCs screen within a Directory Sync Pro for Active Directory profile have the appropriate networks access to communicate with the source domain controller holding the PDC Emulator Active Directory FSMO role before a SID History migration is attempted.

In limited scenarios, it is possible that Migrator Pro for Active Directory will not be responsible for creating or updating any accounts in the source or the target domains. In this scenario, Migrator Pro for Active Directory can be configured to communicate with Read Only Domain Controllers (RODCs).

Network/Firewall Requirements

Migrator Pro for Active Directory requires the following network ports to enable full functionality:

Source

Target

Port/Protocol

Workstations and Member Servers

Migrator Pro for Active Directory Server

443 (TCP) or

80 (TCP)

Migrator Pro for Active Directory Server

Source and Target Domain Controllers

135, 137, 389, 445, 1024-5000 (TCP)

389 (UDP)

Migrator Pro for Active Directory Server

Source and Target Domain Controllers

135, 137, 389, 445, 49152-65535 (TCP)

389 (UDP)

Target domain controllers listed in the Target DCs tab

Domain controller in the source environment holding the PDC Emulator Active Directory FSMO role

135, 137, 139, 389, 445, 3268 and 49152-65535 (TCP)

389 (UDP)

 

The following ports need to be opened between workstations/servers and writable domain controllers for a successful domain join operation:

Type of Traffic

Protocol and Port

DNS

TCP/UDP 53

Kerberos

TCP/UDP 88

EPM

TCP 135

NetLogon, NetBIOS Name Resolution

UDP 137

DFSN, NetLogon, NetBIOS Datagram Service

UDP 138

DFSN, NetBIOS Session Service, NetLogon

TCP 139

C-LDAP

TCP/UDP 389

DFS, LsaRpc, NbtSS, NetLogonR, SamR, SMB, SrvSvc

TCP/UDP 445

LDAP SSL

TCP 636

Random RPC

TCP 1024-5000

GC

TCP 3268

GC

TCP 3269

DFS-R

TCP 5722

Random RPC

TCP 49152-65535

4.5 SSL Certificate Requirements

4.5 SSL Certificate Requirements

Migrator Pro for Active Directory does not require HTTPS (HTTP with SSL), and can operate using HTTP. However, it is strongly recommended to implement Migrator Pro for Active Directory using HTTPS to secure communications between the devices to be migrated and the Migrator Pro for Active Directory Server. In order to activate HTTPS on the IIS component in Windows, the Migrator Pro for Active Directory system will require that a SSL certificate is present.

An SSL Certificate is not provided as part of the installation. For the most secure installation, purchasing an SSL Certificate from a Windows supported 3rd party provider is recommended.

In scenarios where this is not possible, self-signed SSL Certificate can be generated in Windows following these directions: https://technet.microsoft.com/en-us/library/cc753127(v=ws.10).aspx

If using a self-signed certificate, it should be noted that Migrator Pro for Active Directory’s agent component would utilize the operating system’s certificate trust list. Due to the security nature of Active Directory migrations, there is no method of implementing an override and forcing the agent to use an untrusted certificate. If a self-signed certificate is used, that certificate will need to be added to the trusted root certificate list for all computer objects to be migrated. This can be accomplished via group policy: https://technet.microsoft.com/en-us/library/cc738131(v=ws.10).aspx

관련 문서

The document was helpful.

평가 결과 선택

I easily found the information I needed.

평가 결과 선택