지금 지원 담당자와 채팅
지원 담당자와 채팅

Foglight for Storage Management Shared 7.1.0 - User Guide

Getting Started Configuring Agents to Monitor Storage Devices
Brocade SAN Switches Cisco SAN Switches Dell Compellent Arrays Dell EqualLogic PS Series Array Groups EMC CLARiiON CX Series Arrays (CLI) EMC CLARiiON, VNX, or VMAX Storage Arrays (SMI-S) EMC Isilon EMC VPLEX Hitachi Data Systems AMS, USP, and VSP HP EVA Storage Arrays HP 3PAR Arrays NetApp Filers Configuration Procedures
Managing Agents Using Foglight for Storage Management Monitoring Storage Performance Investigating Storage Devices Investigating Storage Components Investigating VPLEX Storage Troubleshooting Storage Performance Managing Data Collection, Rules, and Alarms Understanding Metrics Appendix: Supported Storage Devices Table

Brocade SAN Switches

Foglight for Storage Management uses the SMI-S interface to collect from Brocade SAN switches.

Brocade switch information is collected using the following namespaces:

•
Interop Namespace — interop
•
Working Namespace(Brocade) — root/brocade1
•
Working Namespace(McData) — root/mcdata

Foglight for Storage Management executes the following SMI-S commands to obtain switch information on all SAN switches or Switch Management applications:

•
EnumerateInstanceNames
•
EnumerateInstances
•
References
•
Reference Names
•
Associators
•
Associator Names
•
GetClass

For more information, see the following topics:

•
Requirements for Brocade SAN Switches
•
Configuring Agents to Monitor Brocade SAN Switches

Requirements for Brocade SAN Switches

Requirements differ depending on the version of Brocade Fabric OS (FOS) used by your switch.

Brocade Switches on FOS 7.0 or later

For Brocade switches running FOS 7.0 or later, Foglight for Storage Management collects information from the switches using the Brocade Network Advisor (BNA). Foglight for Storage Management works with either the full commercial version of BNA (license required) or the SMI-S only version of BNA (free).

Your environment must meet the following requirements:

•
Brocade Network Advisor is installed, either the full version or the free SMI-S Only mode version.
•
Brocade switches are not configured as Access Gateway switches. Foglight for Storage Management does not collect from switches configured as Access Gateway switches.
•
Foglight for Storage Management requires a user account with read access. An account with write/admin access is required to add the switch to BNA, but is not required for monitoring.

Brocade Switches on earlier versions of FOS

Foglight for Storage Management collects information from Brocade switches on earlier versions of FOS via a Brocade SMI Agent on a management host. The SMI Agent talks to proxy switches, one in each fabric. These proxy switches are identified through the use of a configuration tool provided by the SMI Agent. Foglight for Storage Management does not perform any configuration of the SMI Agent. The account is native to the SMI Agent.

For information on acquiring, installing, and setting up the Brocade SMI Agent, see:
http://www.brocade.com/services-support/drivers-downloads/smi-agent/index.page

Your environment must meet the following requirements:

•
The Brocade SMI server is installed on a server/host other than the server/host running the Foglight for Storage Management Agent Manager.
•
The SMI Agent is enabled (it is not enabled by default).
•
The SMI Agent requires a CIMOM that is SMI-S 1.1 or 1.2 CTP conformant.
•
Brocade switches are not configured as Access Gateway switches. Foglight for Storage Management does not collect from switches configured as Access Gateway switches.
•
Foglight for Storage Management requires a user account with read access. An account with write/admin access is required to add the switch to BNA, but is not required for monitoring.
관련 문서

The document was helpful.

평가 결과 선택

I easily found the information I needed.

평가 결과 선택