DR Series Software 4.0.4 - Administration Guide

In the DR Series system you can easily view current system license information, upload and install a new license file, as well as unregister a DR2000v system from a DR Series hardware system (license server).

To view and manage licenses in the DR Series system GUI, complete the following steps:

In the left navigation menu, click System Configuration > Licenses.
If you are viewing the Licenses page for any hardware-based DR Series system (that is, not a DR2000v), you can view the following information.
- Registered Licenses—Displays the number of registered licenses for the following categories:
  - Number of DR2000v Licenses Installed
  - Remaining DR2000v Licenses
  - Number of Enclosure Licenses Installed
  - Remaining Enclosure Licenses
- Installed Licenses—Displays a list of installed licenses and the following columns of information.
  - ID—An internal system-related identification number.
  - Expiration Day—Lists N/A unless a DR Series system temporary license is applied in which case it lists the day the license expires.
  - Description—A description of the license, for example, "36TB storage enclosure license."
  - License number—The license number.
  - Status—The license status, such as "enabled" if in use
- Registered DR2000V(s)—Displays a list of the DR2000v systems (if any) registered to the DR Series system and the following columns of information, which is dependent on the name and email information registered on the DR2000v.
  - Customer Name—The name registered on the DR2000v when registering the system.
  - VM Name—The hostname of the VM.
  - Capacity—The capacity of the DR2000v.
  - Email—The email address of the administrator registered on this DR2000v.
  - Service Tag—The randomized service tag number generated by the DR2000v.
To upload and install a new license file, at the top of the page under Upload License File, click Select License File, and then browse to and select the license file you want to upload
If you are viewing the Licenses page of a DR2000v, you can view the following details on the license page.
- Client information—Displays information about the current DR2000v.
  - Model—The model of the DR Series system.
  - Company Name—The company name associated with the administrator user, if configured.
  - Administrator Name—The name associated with the administrator user, if configured.
  - Registered—The status of the license registration of this DR2000v as Yes or No.
  - Service Tag—The Service Tag number of the DR2000v.
  - System Name—The hostname of the DR2000v.
  - Administrator Email—The email address associated with the administrator user, if configured.
  - Storage—The storage capacity of the DR2000v
  - Comments—Any comments entered to describe this system.
- Server information —Displays information about the DR Series hardware system to which the DR2000v is registered.
  - Model—The model of the DR Series system to which the DR2000v is registered.
  - Server license—The IP address of the licensed DR Series system.
  - Update time—The timestamp of the last time the DR2000v synced with the DR Series system.
On the DR2000v Licenses page, to unregister a DR2000v license from its associated DR Series license server, do the following:
1. On the Action menu in the upper right corner of the page, click Unregister.
2. In the Warning dialog box, click OK to unregister the license.
To edit the license registration information for a DR2000v, do the following:
1. On the bmenu in the upper right corner of the page, click Edit.
2. In the Edit Registration pane, modify the following information as needed, and then click Save.
  - IP Address/Hostname of DR License Server—The IP address/hostname of the DR Series system/license server to which this DR2000v is registered.
  - Administrator Name—The name of the administrator user.
  - Adminstrator Email—The email address associated with the administrator user.
  - Company Name—The company name associated with the administrator user.
  - Comment—Text comments entered to describe this system.

Configuring networking settings

In the DR Series system GUI, you can view and modify the network settings (for example, if you want to change the settings you configured when you first initialized the system)

To view and modify networking settings, complete the following steps.

In the left navigation menu, click System Configuration > Networking.
Under Hostname, you can view the following settings.
- Hostname
  - Hostname (FQDN)
  - iDRAC IP Address
- DNS
  - Domain Suffix
  - Primary DNS
  - Secondary DNS
To edit the Hostname or DNS settings, in the Action menu in the upper right corner of the page, click Edit.
1. In the Hostname field, modify the hostname as needed. The hostname entry must meet the following requirements:
  - Alphabetic—allows A-Z, a-z, or a combination of upper and lower case alphabetic characters.
  - Numeric—allows numerals zero (0) through 9.
  - Special characters—allows only the dash (-) character.
  - Length limit—hostnames cannot exceed the maximum length of 19 characters.
2. Modify the DNS fields as needed (Domain Suffix, Primary DNS, Secondary DNS).
  - Domain Suffix — enter a domain suffix to use. For example, acme.local. This is a required field.
  - Primary DNS—enter an IP address that represents the primary DNS server for your system. This is a required field.
  - Secondary DNS—enter an IP address that represents the secondary DNS server for your system. This is an optional field.
3. Click Save.
Under Interfaces, you can view the following columns of information for a selected NIC bond or Ethernet port.
- Device—The name of the device.
- Enabled—Yes or no.
- IP Address—The IP address of the NIC bond or Ethernet port.
- MAC Address—The IP address of the NIC bond or Ethernet port.
- MTU—The Maximum Transmission Unit setting. (The MTU setting accepts values between 512 and 9000.)
- Traffic—The type of traffic as Replication, Management, Backup, and Opdup.
You can click the Device to expand to view more details, such as the interface name, mode, member interfaces, netmask address, gateway address, bonding option, NIC, MAC, maximum speed, and duplex.

To modify settings for a selected interface (NIC bond or Ethernet port), in the Action column, click the Edit icon.

In the Edit Interface pane, for IP Mode, select Static (to set static IP addressing for your system) or DHCP (to set dynamic IP addressing for your system).
If you selected Static for the IP Mode, enter the IP , Netmask, and Gateway addresses. (the system IP address and netmask identify the network to which your system belongs).

For MTU, enter a number to set as the maximum. (The MTU setting accepts values between 512 and 9000.)

NOTE: Ensure that the value that you enter in MTU is the same for the clients, Ethernet Switch, and the appliance. The connection between the clients, the Ethernet switches, and the appliance will break if the MTU number is not the same on all the components.

NOTE: In computer networking, jumbo frames are Ethernet frames with more than 1500 bytes of payload (but in some cases, jumbo frames can carry up to 9000 bytes of payload). Many Gigabit Ethernet switches and Gigabit Ethernet network interface cards support jumbo frames. Some Fast Ethernet switches and Fast Ethernet network interface cards also support jumbo frames. Some computer manufacturers use 9000 bytes as the conventional limit for jumbo frame sizes. To support jumbo frames used in an Internet Protocol subnetwork, both the host DR Series system (initiator or source) and the target DR Series system have to be configured for 9000 MTU.

Consequently, interfaces using a standard frame size and those using the jumbo frame size should not be in the same subnet. To reduce the chance of interoperability issues, network interface cards capable of supporting jumbo frames require specific configurations to use jumbo frames.

To verify that the destination system can support a specific frame size, use the DR Series system CLI command network --ping --destination <IP address> --size <number of bytes>. For more information, contact Technical Support for assistance.

NOTE: Make sure that if you are using any Dell network switches that you take full advantage of the latest switch firmware upgrades and application notes. The application notes provide procedures that assist you in performing switch firmware upgrades and saving configuration files (for complete details, see support.dell.com/ and navigate to Drivers and Downloads for your system type).

NOTE: When setting or changing the MTU value, make sure that you verify that the Ethernet network switch is capable of supporting an MTU size that is equal to or larger than the value you are setting. Any mismatch in MTU values between the clients, Ethernet network switch, and the DR Series system appliance will make it inoperable.

In the Bonding Configuration drop-down list, select one of the following bonding configurations.
- ALB—Configures adaptive load balancing (ALB), which is the default setting.
  Note: ALB load balancing does not balance the load properly when your backup servers are on a remote subnet. This is because ALB uses the address resolution protocol (ARP) and ARP updates are subnet-specific. Because this is the case, ARP broadcasts and updates are not sent across the router. Instead, all traffic is sent to the first interface in the bond. To resolve this ARP-specific issue, make sure that your data source systems reside on the same subnet as the DR Series system.
- 802.3ad—Configures dynamic link aggregation using the IEEE 802.ad standard.
- Caution: If you change the existing bonding setting, the connection to the DR Series system may be lost unless you are sure that the system can accept this bonding type.
Click Save.

Under Bandwidth Limits, you can view the following columns of information, which represent network bandwidth for replication connections:
- Target System—The DR Series system to which network traffic is being sent.
- Target IP—The IP address of the DR Series system to which network traffic is being sent.
- Bandwidth Limit—This limit is shown in KBps, MBps, or GBps and represents the user-set value of the Max Speed.
To modify Bandwidth Limit settings, in the Action column, click the Edit icon.
1. In the Edit Bandwidth Limit pane, for Bandwidth Speed Rate, select Unlimited or Limited.
2. If you select Limited, for Bandwidth Speed Value, enter a number for the bandwidth speed, and then select KBps, MBps or GBps from the drop-down list.
3. Click Save.

Understanding the networking page and Ethernet port values

In the DR Series system GUI, the Networking page displays the currently configured multiple Ethernet ports for the DR Series system in the Interfaces list. For 1–Gigabit Ethernet (GbE) ports in the DR4000 system this could be Eth0, Eth1, Eth2, and Eth3, and in the DR4100 system this could be Eth0, Eth1, Eth2, Eth3, Eth4, and Eth5. For 10-GbE/10-GbE SFP+ NICs, this means that the two ports are bonded together into a single interface. For example, the DR Series system port configuration is as follows:

In a 1-GbE NIC configuration: the DR4000 system supports up to four 1–GbE ports, which consists of up to two internal LAN on Motherboard (LOM) ports and two ports on an expansion card that are bonded together. The DR4100 system supports up to six 1–GbE ports, which consists of up to four internal LOM ports on the network daughter card (NDC) and two ports on a PCI Express expansion card.
In a 10-GbE or 10-GbE SFP+NIC configuration: the DR4000 system supports up to two 10–GbE or 10–GbE SFP+ ports on an expansion card that are bonded together. The DR4100 system supports up to two 10-GbE or 10-GbE SFP+ ports that reside on the NDC that are bonded together.

NOTE: For more information on advanced networking options see the DR Series Command Line Interface Reference Guide available at support.quest.com/dr-series by selecting your specific DR model and then navigating to Technical Documentation.

The ports for bonded NICs display: MAC address, port speed in megabtyes per second (MB/s), maximum speed, and duplex setting. The following example shows Ethernet port values for the four ports in a 1-GbE NIC bonded configuration on a DR4000 system:

Eth0:

MAC: 00:30:59:9A:00:96
Speed: 1000Mb/s
Max Speed: 1000baseT/Full
Duplex: Full

Eth1:

MAC: 00:30:59:9A:00:97
Speed: 1000Mb/s
Max Speed: 1000baseT/Full
Duplex: Full

Eth2:

MAC: 00:30:59:9A:00:98
Speed: 1000Mb/s
Max Speed: 1000baseT/Full
Duplex: Full

Eth3:

MAC: 00:30:59:9A:00:99
Speed: 1000Mb/s
Max Speed: 1000baseT/Full
Duplex: Full

Understanding system operation scheduling

By scheduling system operations, you can optimize your system resources and achieve the best possible DR Series system performance. The most important thing to remember when scheduling critical DR Series system operations is that you want to ensure that you perform each of these operations at a time when it will not overlap or interfere with the running of any of the other key system operations.

You should carefully plan and schedule time periods in which to perform the following critical system operations:

Data ingests (which are dependent upon your usage of your DMA(s))
Replication

System cleaner (space reclamation)

NOTE: Performing scheduled disk space reclamation operations are recommended as a method for recovering disk space from system containers in which files were deleted as a result of deduplication.

In the DR Series system, the main goal in planning and scheduling operations should be to run the Cleaner and Replication operations at times when they do not overlap or interfere with other important system operations. You want to make sure that by properly scheduling and planning, your system can perform each of these key operations independent of the other.

The best practice is to run these two operations during non-standard business hours, so that they do not conflict with any of your other backup or ingest operations.

To view currently scheduled operations and to access the Schedules page to configure system schedules, follow these steps.

On the left navigation menu, click System Configuration > Schedules.
The Schedules page is displayed, showing a daily/hourly calendar representation of currently scheduled operations.

Seleziona il prodotto:

Per una maggiore efficacia, compilare l'Obiettivo della chat:

Soluzioni consigliate per il problema

DR Series Software 4.0.4 - Administration Guide

Managing and viewing DR Series system licenses

Configuring networking settings

Understanding the networking page and Ethernet port values

Understanding system operation scheduling