Chatta subito con l'assistenza
Chat con il supporto

NetVault Bare Metal Recovery 11.0 - User Guide for Plug-ins

Introducing Dell™ NetVault™ Bare Metal Recovery Plug-ins Deploying NetVault Bare Metal Recovery Using the Plug-in Offline Client
Plug-in Server: an overview Installing and removing Plug-in Server Configuring Plug-in Server for use with Plug-in Offline Client Booting a NetVault Bare Metal Recovery Client with Plug-in Offline Client Backing up data with Plug-in Offline Client Restoring data with Plug-in Offline Client
Using NetVault Bare Metal Recovery Plug-in Live Client for Windows®
Plug-in Live Client for Windows: an overview Configuring Plug-in Server for use with Plug-in Live Client for Windows Installing and removing Plug-in Live Client for Windows® Backing up data with Plug-in Live Client for Windows® Booting a NetVault Bare Metal Recovery Client with Plug-in Offline Client Restoring data with Plug-in Live Client for Windows
Using NetVault Bare Metal Recovery Plug-in Live Client for Linux®
Plug-in Live Client for Linux: an overview Installing and removing Plug-in Live Client for Linux Generating a DR image for use with Plug-in Live Client for Linux Creating the required bootable CD for use with Plug-in Live Client for Linux Recovering a DR image for use with Plug-in Live Client for Linux
NetVault Bare Metal Recovery physical-to-virtual recovery Troubleshooting

Booting the NetVault Bare Metal Recovery Client with the Windows® PE-based Plug-in Offline Client

2
When the BMR Network Configuration dialog box appears, select the applicable option:
Use DHCP (recommended): To use the Dynamic Host Configuration Protocol (DHCP) to configure the network interface, select this option.
Use Static IP Address: To enter specific IP addresses, select this option, and enter the addresses in the IP Address, Subnet Mask, and Default Gateway fields.
3
To submit the information, click Config, and then click OK when the confirmation message appears.
4
To close the BMR Network Configuration dialog box and start the NetVault Bare Metal Recovery Agent, click Exit.
You can use the list above the Run button to output information related to the NetVault Bare Metal Recovery GUI when you issue the Run command.

Loading drivers dynamically

In some cases, Windows® PE might recognize the hardware attached to the target machine. To load drivers without having to restart Windows PE, perform the following steps.
3
When the BMR Network Configuration dialog box appears, click Exit to close it.
5
Insert the device created in Step 1, which contains the driver files.
drvload <pathToDriverINFfile>
7
To access the BMR Network Configuration dialog box, type the following at the command prompt, and press Enter:
8
From the Network Adapters list, select the item that you just added, and then continue from Step 2 under Booting the NetVault Bare Metal Recovery Client with the Windows® PE-based Plug-in Offline Client.

Injecting drivers and restarting drdaemon to facilitate storage controller recognition

In some cases, Windows® PE might recognize the hardware attached to the target machine. To load drivers without having to restart Windows PE, perform the following steps.
3
When the BMR Network Configuration dialog box appears, do one of the following:
5
Insert the device created in Step 1, or map to the applicable network drive.
drvload <pathToDriverINFfile>
8
In the Windows Task Manager screen, select the Processes tab, right-click drdaemon, select End Process, and close the Task Manager.
9
To restart the drdaemon, type the following at a command prompt (if necessary, click Launch CMD again), and press Enter:

Injecting drivers into the Plug-in Offline Client image

If you do not, or cannot, use a device such as a USB device, 3.0 protocol or earlier, to load a driver after Windows® PE has started, use the following process to add the driver to the Plug-in Offline Client image and then re-create the Plug-in Offline Client image with the added driver. To complete this process, you must have Windows ADK for Windows 8 installed, the applicable “*.inf” file, a program capable of extracting an ISO image, and a method for repackaging the ISO as a bootable image or bootable CD. The following steps are based on Windows 7; these steps might differ depending on your environment.
2
Install the Windows ADK on a Windows Server 2008 R2, Windows Server 2012, Windows 7, or Windows 8 system.
IMPORTANT: Installation of Windows ADK also installs Microsoft® .NET Framework if it is not already installed. After .NET Framework is installed, the system is automatically restarted.
3
Extract the “NetVault Bare Metal Recovery ISO Builder for Plug-in Offline Client for Windows file to the Windows ADK machine.
This step creates two files, “nvbmrisocreate.exe” and “nvbmriso.pkg.”
5
To create the Windows PE ISO image, navigate to the directory that contains the extracted “nvbmrisocreate.exe” file, type the following at the command prompt, and press Enter:
/TYPE: If you are working with an earlier version of the Plug-in Offline Client, enter WAIK for Windows Automated Installation Kit (AIK). If you are using version 6.1 or later, you can enter ADK.
/PKG: Enter the full path and filename for the Plug-in Offline Client .pkg file that you downloaded separately.
/DIR: Enter the full path to the location of the Windows AIK or ADK directory.
/OUT: Enter the path where the bootable ISO image should be created.
/ADDDRV: Enter the full path where the downloaded device drivers are stored.
/BIT:32: If you need to create a backwards-compatible version of VaultOS for use with a 32-bit version of Windows PE, enter this option.
/PKG:"<pathToFile>\nvbmriso.pkg"
Related Documents

The document was helpful.

Seleziona valutazione

I easily found the information I needed.

Seleziona valutazione