Chatee ahora con Soporte
Chat con el soporte

DR Series DR6300 - Owner's Manual

DR6300 system overview Technical specifications Initial system setup and configuration Pre-operating system management applications
Options to manage the pre-operating system applications System Setup Dell Lifecycle Controller Boot Manager PXE boot
Installing and removing system components
Safety instructions Before working inside your system After working inside your system Recommended tools Front bezel (optional) System cover Cooling shroud Cooling fans Cooling-fan assembly System memory Processors and heat sinks PCIe card holder Cable retention bracket Integrated storage controller card Expansion cards and expansion card riser Internal dual SD module (optional) Network daughter card Internal USB memory key (optional) System battery Power supply units (PSU) System board Trusted Platform Module Hard drives Hard drive backplane SD vFlash card (optional) Control panel assembly
Using system diagnostics Jumpers and connectors Troubleshooting your system

System battery specifications

Your Dell DR6300 system supports CR 2032 3.0-V lithium coin cell system battery.

Expansion bus specifications

The Dell DR6300 system supports PCI express (PCIe) generation 3 expansion cards, which need to be installed on the system board using expansion card risers. This system supports three types of expansion card risers. The following table provides the expansion card riser specifications:

Table 14. Expansion card riser specifications

This table describes the details of the PICe slots on the expansion card risers. Riser 1 supports PCIe slots 1 through 3, with half height, low profile, x8 link speed cards. Riser 2 supports two PCIe cards on slots 4 and 5. PCIe slot 4 supports a full height, full length, x16 card and PCIe slot 5 supports a full height, full length x8 card. Riser 3 has two card options. The alternate Riser 3 option supports a single PCIe card on PCIe slot 6. The PCIe slot 6 supports a full height, full length x16 card.

Expansion card riser

PCIe slots on the riser

Height

Length

Link

Riser 1

Slot 1

half-height

low-profile

x8

Riser 1

Slot 2

half-height

low-profile

x8

Riser 1

Slot 3

half-height

low-profile

x8

Riser 2

Slot 4

full-height

full-length

x16

Riser 2

Slot 5

full-height

full-length

x8

Riser 3 (alternate)

Slot 6

full-height

full-length

x16

* 
NOTE: When using slots 1 through 4 on the riser, ensure that both the processors are installed on the system.

Memory specifications

The Dell DR6300 system supports DDR4 registered DIMMs (RDIMMs). Supported memory bus frequencies are 1333MT/s, 1600 MT/s, 1866 MT/s, 2133MT/s, or 2400 MT/s.

Table 15. Memory specifications

Your system supports 24 memory module sockets of 288-pins each. The system supports RDIMMs of memory capacity 4 GB, 8 GB, or 16GB single rank, and RDIMMs of memory capacity 8 GB, 16 GB, or 32 GB dual rank. For system with single processor, the minimum RAM is 4 GB and for dual processor systems the minimum RAM is 8 GB.

Memory module sockets

Memory capacity

Minimum RAM

Maximum RAM

Twenty-four 288–pin

8 GB or 16 GB dual-ranked RDIMMs
•
4 GB with single processor
•
8 GB with dual processors (minimum one memory module per processor)

128 GB with two processors

Drive specifications

Hard drives
Hard drives

The Dell DR6300 system supports up to twelve 3.5-inch hard drives and two optional 2.5-inch back-accessible SAS, SATA, or Nearline SAS hard drives.

Documentos relacionados

The document was helpful.

Seleccionar calificación

I easily found the information I needed.

Seleccionar calificación