Chatee ahora con Soporte
Chat con el soporte

vRanger 7.8.5 - User Guide

Introduction vRanger overview Configuring vRanger
Configuring vRanger through the Startup Wizard Configuring vRanger manually Supplemental instructions: additional repository types
Using vRanger Backup Restore
Restoring an encrypted VMware VM Performing a full restore for VMware VMs Performing a full restore for Hyper-V® VMs Performing a full restore for VMware vApps Performing a full restore of a physical machine Performing an FLR on Windows Performing an FLR on Linux Restoring from manifest
Replicate VMs Reports Integrating and monitoring vRanger Using the vRanger Console vAPI Cmdlet details

Removing an EMC DD Boost repository

The process for removing an EMC® Data Domain® Boost (DD Boost™) repository is the same as removing any other repository type, except that you also have the option of removing the storage unit used by the repository. There is a hard limit on the number storage units that can be configured on a Data Domain device, which makes removing unused storage units an important maintenance effort.

1
In the My Repositories pane, right-click the applicable EMC Data Domain Boost repository, and select Remove.
The Remove Repository dialog box appears, showing the savepoints in the selected repository.
2
Select Delete all savepoints in this repository.
3
To delete the savepoints in a replicated repository, select Delete all savepoints in replication repository.
4
5
When the Delete Savepoints dialog box appears, select Delete DD Boost storage unit, and click OK.

Adding a Quest Rapid Data Access (RDA) repository

The Quest DR Series disk-based data protection appliances optimize storage utilization and reduce network bandwidth requirements with in-line deduplication, server-side compression, and compressed and deduplicated replication.

The Quest DR Series include the following appliance types:

DR4000 System: This version consists of preinstalled Quest DR System software on a Dell™ PowerEdge™ R510 appliance platform.
DR4100 System: This version consists of preinstalled Quest DR System software on a Dell PowerEdge R720xd appliance platform.
DR6000 System: This version consists of preinstalled DR6000 system software on a Dell PowerEdge R720xd appliance platform. This version differs from the DR4100 by including a higher level of base system hardware.

The Quest DR Series supports Common Internet File System (CIFS), Network File System (NFS), and RDA protocols. The RDA protocol provides a logical disk interface for the Quest DR Series system, and enables better coordination and integration between vRanger and the Quest DR Series system and provides for client-side deduplication of vRanger backups.

For more information about the Quest DR Series systems, see the Quest DR Series System Administrator Guide.

Adding a Quest DR Series system as an RDA repository

The following process describes how to add a Quest Rapid Data Access (RDA) repository. The following procedure assumes that:

1
In the My Repositories pane, right-click anywhere, and click Add > Quest Rapid Data Access (RDA).
2
In the Add Quest Rapid Access Repository dialog box, complete the following fields:
Repository Name: Enter a descriptive name for the repository.
Description: [Optional] Enter a long-form description for the repository.
DNS Name or IP: Enter the DNS name or IP address of the Quest DR Series system.
RDA Username: Enter a user account that can be used to log in to the device. On the Quest DR Series system, only one user account exists, and the user ID for that account is backup_user. You can only change the password for this account; you cannot create an account or delete the existing account.
RDA Password: Enter the password for the user account. The default is: St0r@ge!
Logical Storage Unit: Enter the name of the storage container. Ensure that the container is created before you add the device. You cannot add the device if the specified container does not exist on the device. When creating the storage container, use the options:
Port Number: Leave this value at 0 to use the default.
3
The connection to the repository is tested and the repository is added to the My Repositories pane and the Repository Information dialog box.
Import as Read-Only: To import all savepoint data into the vRanger database, but only for restores, click this button. You cannot back up data to this repository.
Import: To import all savepoint data into the vRanger database, click this button. vRanger is able to use the repository for backups and restores. vRanger requires read and write access to the directory.
Overwrite: To retain the savepoint data on the disk and not import it into vRanger, click this button. vRanger ignores the existence of the existing savepoint data and treats the repository as new.

Configuring repository replication

Data Replication is configured through the My Repositories pane of the vRanger interface.

TIP: For more information on repository replication, see the Quest DR Series System Administrator Guide.

The following procedure assumes that:

1
In the My Repositories pane, right-click the Quest Rapid Data Access (RDA) repository, and select Configure Replication.
2
In the Configure Replication dialog box, complete the following fields:
Repository Name: Enter a descriptive name for the repository.
Description: [Optional] Enter a long-form description for the repository.
DNS Name or IP: The DNS name or IP address of the Quest DR Series system.
RDA Username: Enter a user account that can be used to log in to the device. On the Quest DR Series system, only one user account exists, and the user ID for that account is backup_user. You can only change the password for this account; you cannot create an account or delete the existing account.
RDA Password: Enter the password for the user account.
Logical Storage Unit: Enter the name of the storage container. Ensure that the container is created before you add the device. You cannot add the device if the specified container does not exist on the device. When creating the storage container, use the options:
Port Number: Leave this value at 0 to use the default.
3

After replication is configured for a repository, the Configure Replication option is disabled for that repository.

You may edit an existing replication configuration to update credentials or timeout values. You may also use the Edit Repository Details dialog box to view free space for the repository.

1
In the My Repositories pane, right-click the Quest Rapid Data Access (RDA) repository, and select Edit Replication Configuration.
2
In the Edit Quest Rapid Data Access (RDA) dialog box, edit any of the following fields:
3
Alternatively, view the Free Space field for up-to-date information about this repository.
Documentos relacionados

The document was helpful.

Seleccionar calificación

I easily found the information I needed.

Seleccionar calificación