NetVault 13.1.2 - Administration Guide

Setting restore type

On the Advanced Options page, click Restore Type, and select one of the following options.

Table 62. Restore type
Option	Description
Restore from selected backup	This option is selected by default. To restore data from the selected backup, leave this option selected.
Restore from latest backup	Select this option to restore data from most recent backup that was performed using a particular Backup Selection Set regardless of which saveset you use to create the restore job.

The following example illustrates the difference between these two options:

Create a test directory and create a Backup Selection Set “SelectionSet-1” to back up the test directory.

Create a file named “first.txt” in the test directory.

Perform a Full Backup (TestBackup1) using “SelectionSet-1.”

Delete “first.txt” and create a file named “last.txt” in the test directory.

Perform a second Full Backup (TestBackup2) using “SelectionSet-1.”

Restore TestBackup1 using the Restore from selected backup option. This job restores the file “first.txt.”

Restore TestBackup1 using the Restore from latest backup option. This job restores the file “last.txt.”

Click Set to save the settings and close the dialog box.

Specifying additional options

To specify additional options for a restore job

On the Advanced Options page, click Additional Options, and configure the following option:

•

Use Network Compression: To use network compression while transferring data over the network, select this check box. The data is compressed on the server or client to which the source device is attached before being transferred over the network. On the target client, the data is decompressed before being restored to the original or alternate location.

Network compression does not work for the following types of jobs:

•

Restores from NetVault SmartDisk

•

Restores from devices attached to NDMP-based NAS filers

•

Restores performed using the Plug-in for NDMP, Plug-in for NetWare, and NetVault Bare Metal Recovery products

Click Set to save the settings and close the dialog box.

Configuring pre- and post -scripts for restore jobs

You can use the pre- and post-script options to run user-defined scripts before a job starts or after a job completes. You can use these scripts to perform tasks such as dismounting or shutting down a database before the job starts or mounting or starting the database after the job completes.

Before configuring pre- or post-scripts, review the following information:

•

The script should be an executable file, for example, “.bat” files on Windows and “.sh” files on Linux.

•

The script file should reside on the target client. It should be available in the scripts directory under the NetVault installation directory.

•

The pre- and post-scripts can contain run-time parameters. These parameters are stored in the environment variable NV_USER_ARG. You can also use other NetVault environment variables in the scripts. For a list of available environment variables, see Environment variables in NetVault.

•

NetVault provides two predefined script files that can be used as post-scripts:

•

psmail: Use this script to send job completion status to the specified email addresses.

•

psmail_logs: Use this script to send job completion status and job logs to the specified email addresses.

On Linux and UNIX, the predefined scripts do not any filename extension. On Windows, the scripts have the filename extension “.bat.” To run these scripts, specify the following in the Post Script box:

•

Linux and UNIX: psmail or psmail_logs

•

Windows: psmail.bat or psmail_logs.bat

To specify pre- and post -scripts

On the Advanced Options page, click Pre & Post Scripts, and configure the following settings.

Table 63. Pre and post script options for restore jobs

Option

Description

Pre Script

This option allows you to run a user defined script before a job starts. You can use this script to perform any pre -restore preparation, like dismounting or shutting down a database.

To run a pre -script, do the following:

•

In the Pre Script box, specify the script filename.

•

In the User Parameter box, provide the values for the run -time parameters. The value should be valid and conform to its usage in the script. NetVault does not perform any validity checks for the user parameters.

Post Script

This option allows you to run a user-defined script after a job completes. You can use this script to perform any post restore processing, such as mounting or starting a database after a job completes.

To run a post -script, do the following:

•

In the Post Script box, specify the script filename.

•

In the User Parameter box, provide the values for the run-time parameters. The value should be valid and conform to its usage in the script. NetVault does not perform any validity checks for the user parameters.

Click Set to save the settings and close the dialog box.

Table 64. Script execution and restore job status

The following table illustrates the effect of script exit status on the overall execution and job status.


Process	Result
Pre script	Success	Success	Success	Fail	Fail	Fail
Restore job	Success	Success	Fail	Does not run	Does not run	Does not run
Post script	Success	Fail	Success	Success	Not configured	Fail
Overall job status	Job completes successfully	Job completes, but a post -script error is reported	Job fails, but the pre -script and post -script runs. An error is reported	Job fails, and a pre -script error is reported, but post -script runs	Job fails, and a pre -script error is reported	Job fails. Pre -script and post -script errors are reported

Configuring user-defined events for restore jobs

When creating a restore job, NetVault lets you configure user-defined events that can be raised when the job completes successfully, completes with warnings, or fails. You can use these options when you want to be notified about the completion status of individual jobs.


	NOTE: NetVault includes several predefined events, which are raised for significant occurrences within the system. For more information, see About NetVault events and Events types. You can also raise user-defined events for individual backup jobs, restore jobs, report jobs, policies, and log messages. You can use various notification methods to receive notifications when the predefined or user‑defined events occur in NetVault. For more information, see Using global notification methods.

You can configure the user-defined events in the Restore Advanced Options Set. Once you create a user‑defined event, you can raise it for any job or backup policy. NetVault adds the user-defined events to the event class Jobs — User defined. You can then set up one or more notification methods for the event to receive notifications when the event is raised.

To raise user-defined events for a restore job:

On the Advanced Options page, click Events, and configure the following settings.

Table 65. User-defined event types for restore jobs
Option	Description
Job is Successful	Type or select the event that you want to raise when the job completes successfully.
Job has Warnings	Type or select the event that you want to raise when the job completes with warnings.
Job Fails	Type or select the event that you want to raise when the job fails.

Click Set to save the settings and close the dialog box.

To receive a notification when an event occurs, set up a notification method for the event. For more information, see the Setting up a global notification method.

Seleccione su producto:

Con el fin de ofrecerle un mejor servicio, complete el campo Motivo del chat:

Soluciones recomendadas para su problema

NetVault 13.1.2 - Administration Guide

Setting restore type

Specifying additional options

Configuring pre- and post -scripts for restore jobs

Configuring user-defined events for restore jobs