Chatee ahora con Soporte
Chat con el soporte

NetVault 13.0.1 - Built-in Plug-ins User Guide

Encrypting all backups

If encryption is enabled for all backups performed from a particular NetVault Client, there are no additional requirements for encrypting backups. For more information about the backup and restore procedures, see the user’s guide for the relevant plug-in.

Performing job-level encryption

The job-level encryption option can be used to encrypt the primary backup, secondary copy, or both. Encrypting both the primary backup and secondary copy is beneficial when security requirements dictate that the backup must be encrypted while it transfers across the network or while it is stored on a disk-based backup device even if the disk-based backup device is located within the corporate network.

The job-level encryption setting is specified in the Backup Advanced Options Set. For more information about creating an Advanced Options Set for a backup job, see the Quest NetVault Administrator’s Guide.

For more information, see the Quest NetVault Administrator’s Guide.
2
Click Additional Options.
3
In the Additional Options dialog box, select the Enable Encryption check box.

NetVault offers the following methods for creating Secondary Copies:

Duplicate: The Duplicate method creates an exact copy which is linked to the original backup. This method breaks down the backup into segments and copies the segments to the storage device. During restore, the segments from the primary backup and secondary copy are interchangeable. As it is not possible to mix unencrypted segments with encrypted segments during restore, you cannot enable or disable encryption for the Duplicate. If the original saveset is encrypted, the Duplicate method creates an encrypted copy. If the original saveset is not encrypted, this method creates an unencrypted copy.
Data Copy: The Data Copy method breaks down the backup into segments and copies the segments to the backup device. During restore, either the primary backup or the secondary copy is used to recover data; the segments from the primary backup and secondary copy are not interchangeable. Therefore, it is possible to enable encryption for the Data Copy when the primary copy is unencrypted. This option is useful when you want to use the deduplication option for primary backups.
For more information, see the Quest NetVault Administrator’s Guide.
2
Click Secondary Copy.
3
In the Secondary Copy dialog box, select the Create Secondary Copy check box.
4
Select the Encrypt Secondary Copy Only check box.
IMPORTANT:  
If the primary copy is encrypted, the Data Copy method automatically creates an encrypted saveset whether you select the Encrypt Secondary Copy Only check box or not. Therefore, this option is only useful when you want to create an encrypted secondary copy from an unencrypted primary copy.
Encrypted primary backups are not encrypted again if you select the Encrypt Secondary Copy Only check box for a Data Copy.

Using Plug-in for Databases

Using Plug-in for Databases

Configuring default settings

1
Start the Backup Job Wizard, and click Create New next to the Selections list. Open the NetVault Server or Client node. Select NetVault Databases and click Configure.
You can also configure the default settings from the Change Settings page. In the Navigation pane, click Change Settings. On the Configuration page, click Server Settings, and then on the NetVault Server Settings page, click Plugin Options.
2
Under NetVault Database Backup, configure the following settings.

Minimum free space on database device before warning is output

This setting specifies the minimum amount of free disk space required on the drive or partition on which the db directory resides. By default, it is set to 20 percent of the total size of the NetVault Database.

To change this limit, type or select a new value.

If the available free space falls below the specified level, the plug-in logs a warning message.

Minimum free space on logs device before warning is output

This setting specifies the minimum amount of free disk space required on the drive or partition on which the logs directory resides. By default, it is set to 10 percent of the total size of the log files.

To change this setting, type or select a new value.

If the available free space falls below the specified level, the plug-in logs a warning message.

Minimum free space on reports device before warning is output

This setting specifies the minimum amount of free disk space required on the drive or partition on which the reports directory resides. By default, it is set to 10 percent of the total size of the Reports Database.

To change this setting, type or select a new value.

If the available free space falls below the specified level, the plug-in logs a warning message.

Format to be used while backing up NetVault Database

The NetVault Database backups can be generated in tar and custom formats. By default, the plug-in uses the custom format.

The tar format has the following limitations:

It requires a large amount of disk space to store temporary files during backup. The backup could fail if the tmp directory in the NetVault installation directory does not have sufficient space to store the files.
3
Click OK or Apply to save the settings.
Documentos relacionados

The document was helpful.

Seleccionar calificación

I easily found the information I needed.

Seleccionar calificación