FAM-7557

Fixed the vulnerabilities CVE-2016-5007/CVE-2016-9878/CVE-2018-15756.

FAM-7587

Fixed the issue that Foglight Management Server failed to get Agent Manager IP address in new Linux distributions.

Defect ID

Known Issue

FAM-7697

The connection test via installation GUI or headless would take about 2 minutes when FglAM and FMS are in different FIPS modes.

FAM-7559

Agents fail to monitor the WinServer2019 Domain Controller via DCOMWindowsCommandShell connection.

FAM-7381

HA failover fails and Agent Manager Agents become broken, once the Management Server deployed in the HA environment is restarted.

FAM-7365

The Infrastructure agent fails to collect the data due to the "Failed setting a value for obsolete node:" error.

FAM-7342

Part of data collected on the Host dashboard is missing due to ConnectionBrokenException.

FAM-7341

The CPU usage of the Agent Manager constantly reaches 100%.

FAM-7330

The "sqlserv.exe process" and "Memory Top Consumers" metrics collected by the Windows Agent are incorrect. 
Workaround: When FglAM running in Linux to monitor Windows, it is recommended to use WinRM instead of WMI.

FAM-7307

Many errors show in the Agent Manger log and there is no data displayed on the VMware dashboard.

FAM-7210

The Agent Manager version number is incorrect on the Script Console dashboard, after being upgraded to 5.8.5.5.2 from 5.8.5.5.1.

FAM-7209

FglAM-Adapter-Devkit-6.1.3 is missing after the Agent Manager is upgraded from 5.8.5.4.1 to 5.8.5.4.2.

FAM-7193

FglAM running on Linux/Solaris fails to connect to the target host through link-local IPv6 WMI, if multiple network interfaces exist in the target host.
Workaround:
1. Log into the target host.
2. Execute the dos command->ipconfig/all command, to check how many tunnel interfaces which contain IPv6 address.
3. If only Tunnel adapter Teredo Tunneling Pseudo-Interface and Ethernet adapter Local Area Connection exist in the target host, uninstall/disable Teredo Tunneling Pseudo-Interface, and then check if the WMI connection can be established. 

FAM-7169

WinRMCommandShell returns empty output when using BAT scripts.

FAM-7116

WMI connection cannot be established successfully when using the IPv6 address to monitor the target host.
Workaround:
1. Set the agent's target host address and credential resource mapping to the long form, for example: fc00:0:0:0:0:0:a1e:9804.
2. Check if the WMI connection can be established. If not, change the agent's target host address from long form to compressed form (fc00::a1e:9804). If this solution still does not work, check the workaround in FAM-7193.

FAM-7023

Agents will be broken (FMS deletes them), after changing FglAM host name, IP, or display name. The agents will be recreated when the FglAM starts with the original FglAM display name.

FAM-6998

Cannot deploy multiple HA-aware gars to a standby host at one time.
Workaround:

1. Log in to http://<foglight_home>:8080/jmx-console, and then click name = HAManager.

2. In the page that opens, click Invoke for the diagnosticSnapshotAsString() API.

3. Find the appropriate primary HA host (mState = PRIMARY).

4. Log in to http://<foglight_home>:8080/, and then go to Dashboards > Administration > Agents > Agent Managers.

5. Select the primary HA host found in step 3, and click Deploy Agent Package.

6. In the dialog box that appears, select multiple agent packages to deploy.

7. Click Next, and then click Finish to start the deploy task.
   When the deploy task completes, the agent packages deployed to the primary host will be automatically deployed to the standby host in a few minutes.

FAM-6942

HA failover fails and the value of mState on standby peers changes to MISSING_LOCKBOX in JMX console.
Workaround: If the failure of HA failover is caused by MISSING_LOCKBOX (Check the HA partitions info by navigating to JMX console > HAManager > diagnosticSnapshotAsString()), perform either of the following options to resolve this issue:
1. On the navigation panel, under Dashboards, click Administration > Credentials > Manage Lockboxes. In the Manage Lockboxes dashboard, release the missed lockboxes to the MISSING_LOCKBOX FglAM client. If you cannot find the missed lockboxes, perform step 2.
2. On the FglAM client that has the MISSING_LOCKBOX status, navigate to <fglam_home>\state\<state_name>\credentials. Clean up all files under this directory, and then restart the FglAM. After the restart completes, release all lockboxes as Primary in the Administration > Credentials > Manage Lockboxes dashboard.

FAM-6940

There are duplicate IP addresses for different FglAM instances (running on Linux) in the Agent Managers dashboard, if the FglAM servers are cloned virtual machines.
Workaround 1:

1. Go to the monitored host, and then execute the following commands:
   su root
   rm -f /etc/machine-id
   systemd-machine-id-setup

2. Restart the FglAM. Restart the operating system if this issue still exists after restarting the FglAM.

Workaround 2:

1. Set system.id.enabled = false for all FglAM instances in the <fglam_home>/state/<state_name>/config/client.config file.

2. Change the display name in the <fglam_home>/state/<state_name>/config/fglam.config.xml file, and then restart the FglAM.

Workaround 3: If you have cloned the servers, do not start up the FglAM. Set system.id.enabled = false for all FglAM instances in the <fglam_home>/state/<state_name>/config/client.config file, and then start the FglAM for the first time.

FAM-6934

Agent is not listed under "agents" property of FglAMClientInstance or Host object after moved.

FAM-6688

Support is required for installing and running Agent Manager on a system with SELinux enabled.

FAM-6439

Upgrades from 5.7.4 to 5.8.1 or 5.8.2 may result in an error during the upgrade process.

Workaround: If you are currently running a 5.7.4 install and you want to upgrade, then you must upgrade to version 5.8.5 or later.

FAM-5854

Foglight Log Monitor does not support UNC (Universal Naming Convention) paths.

Workaround: The following workaround applies when monitoring local log files. Monitoring remote log files is not supported.

1. Map the UNC path to a drive letter on the local machine running the Agent Manager.

2. If any monitored log files are residing in the UNC path, point the Log Monitor Agent to this location using the mapped drive letter, not its UNC path.

FAM-5832

Installing and configuring multiple Foglight Agent Manager instances on a single physical host can cause some topology churn in the Host model representing the Agent Manager.

Workaround: By default, the Agent Manager submits performance metrics about itself. If multiple Agent Manager instances are running on the same physical host, disable the performance monitoring self-metric submission for each Agent Manager Instance by completing the following steps:

1.  Open the $FGLAM_STATE/config/baseline.jvmargs.config file for editing.

2. Add the following entry to the vmparameter. properties section of the file:
   
   vmparameter.<X> = "-Dquest.glue.disable.performancemonitor=true";
   
   Important. You must replace <X> with the next numeric sequence number.
   
   

3.  Save the file.

4.  Restart the Agent Manager

Additionally, an Agent that submits a Host object representing the monitoring host (for example, an Agent Manager instance that is running and hosting an agent instance) as part of its monitored collection causes a Host topology churn when these agent types are deployed to additional Agent Manager instances running on the same physical host.
If the monitoring agent's type supports it, its configuration should be adjusted to prevent the submission of monitoring host system ID. For example, this configuration is available for the Foglight for Infrastructure Agents and can be disabled by setting the agent instances' Collect System ID property to false.

FAM-5600

The Agent Manager vm.config file migration fails under multi-state installs.

Workaround:  The legacy vm.config file is replaced with two new configuration files: client.config and baseline.jvmargs.config. Locate these files within the upgraded Agent Manager state instance. As these file instances may already contain transferred values from the legacy vm.config, review each of the settings in both of these files in order to ensure that these configuration options apply to the Agent Manager state instance that they are being copied into.

1. Locate the vm.config file within the configuration state directory instance of the Agent Manager. The bottom of the file contains a section for defining vmparameter.x = ""; values. Copy over these settings from vm.config here into the baseline.jvmargs.config file.

2. Review all of the options declared in vm.config with those of client.config that you have copied over. The client.config file is a super-set of properties from vm.config (with the exception of vmparameter values that are no longer defined here). So each property that exists in vm.config should also exist in client.config. Ensure that each of the common configuration values in the client.config file matches the values in the vm.config, and make any updates, if required.

3. If the java.vm configuration parameter was set in vm.config, then you should update this option in the new client.config file. When transferring this value over, ensure that the path value is quoted and backslashes escaped. For example:
   
   Windows: java.vm = "C:\\shared_java_vms\\1.5\\jre";
   Unix: java.vm = "/opt/shared_java_vms/1.5/jre";
   

4. After validating that all of the configuration settings are in their new locations, delete the vm.config file and restart the Agent Manager process.

FAM-5355

OutOfMemoryError: The Agent Manager cannot create new native thread. It shuts down when the open file descriptor limit is too low.
Workaround: When creating a large number of agents on a single Agent Manager instance, you must ensure that the maximum number of open file descriptors (displayed by the ulimit -n command) is set high enough. 256 is the minimum suggested for an Agent Manager installation and 512 or more is recommended for an Agent Manager hosting up to 15 agents. 1024 is recommended for an Agent Manager hosting more than 15 agents. This value may need to be adjusted even higher if more agents are created on a single Agent Manager install.

FAM-5264

The Agent Manager running on Solaris may fail to run local or external commands during startup or through the SSHLocalConnectionImpl class.

FAM-4955

Parentheses can cause a command execution to fail while using a LocalWindowsCommandShell connection.

Workaround: If parentheses are used for grouping commands (and not in an echo context), use spaces to separate them from the other tokens in the command. For example, instead of this command:

if 3 gtr 2 (echo "3>2") else (echo "3 leq 2")

Use the following:

if 3 gtr 2 ( echo "3>2" ) else ( echo "3 leq 2" )

FAM-2850

Slave processes exist for all installed out-of-process (OOP) agent packages, even if no agent instances are running.

Workaround: OOP packages which are not running any agent instances may be un-deployed from the Agent Manager. Currently, this is only possible using a manual procedure.

FAM-1972

The deployed agent scratch directory created for JFogbank-type agents is not deleted during an upgrade.

Workaround: The orphaned directory is benign, and can be manually deleted after the upgrade is complete.