Foglight Agent Manager 5.9.1 - Foglight Agent Manager Guide

MaxConcurrentOperationsPerUser: This parameter specifies the maximum number of concurrent Enumeration operations allowed by an individual user. The value must be in the range of 1 to 4294967295.

This parameter is only available for WinRM version 2.0 and later. In version 1.1, the MaxConcurrentOperations parameter is used instead.

To increase the value assigned to this parameter, issue the following command:

winrm set winrm/config/service @{MaxConcurrentOperationsPerUser="<number>"}


	TIP: WinRM parameters can also be edited using the Group Policy Object Editor. To start the editor, type gpedit.msc at the command line, and then navigate to Local Computer Policy > Computer Configuration > Administrative templates > Windows Components > Windows Remote Management (WinRM) and Windows Remote Shell.

Figure 1. Windows Components in the Local Group Policy Editor

•

MaxConcurrentOperations: This parameter specifies the maximum number of concurrent shells any user can remotely open on the same system. Any number from 1 to 4294967295 can be used. For more information about this parameter, you can visit the following Web page: http://msdn.microsoft.com/en-us/library/cc251426.aspx.

This parameter is only available for WinRM version 1.1. It is deprecated for version 2.0 and later, and MaxConcurrentOperationsPerUser is used instead.

To increase the value assigned to this parameter, issue the following command:

winrm set winrm/config/service @{MaxConcurrentOperations="<number>"}

•

MaxShellsPerUser: This parameter specifies the maximum number of concurrent shells any user can remotely open on the same system. Any number from 0 to 2147483647 can be used, where 0 means unlimited number of shells. If this policy setting is enabled, the user cannot to open new remote shells if the count exceeds the specified limit.

To increase the value assigned to this parameter, issue the following command:

winrm set winrm/config/winrs @{MaxShellsPerUser="<number>"}

•

AllowRemoteShellAccess: This parameter controls access to the remote shell. It must be set to true.

To set this parameter to true, issue the following command:

winrm set winrm/config/winrs @{AllowRemoteShellAccess="true"}

For additional information, visit the following Web page:

http://msdn.microsoft.com/en-us/library/windows/desktop/aa384372%28v=vs.85%29.aspx

About WinRM connection ports

WinRM uses a set of default ports for communication. Depending on the WinRM version, the following port numbers are used:

•

WinRM 1.1 and earlier: The default HTTP port is 80, and the default HTTPS port is 443.

•

WinRM 2.0 and later: The default HTTP port is 5985, and the default HTTPS port is 5986.

After issuing the winrm quickconfig command, the listener port number can be determined using the winrm enum winrm/config/listener command. For example:

> winrm enum winrm/config/listener

Listener

Address = *

Transport = <HTTP|HTTPS>

CertificateThumbprint

ListeningOn = <ip_addresses>

Troubleshooting

If you have verified all of the WinRM configuration information and are still experiencing connection issues, the following techniques may be helpful for diagnosing the problem.

Verifying setup

To check whether a listener is configured for WinRM, you can issue the following command and observe its output:

$ winrm enum winrm/config/listener

CertificateThumbprint

ListeningOn = 10.4.114.29, 127.0.0.1, ::1, fe80::100:7f:fffe%12, fe80::5efe:

10.4.114.29%14, fe80::38a7:8fc9:3d7d:f4d7%13

The Port and Transport elements contain important information. The above command output identifies an HTTP listener on port 5985.

To see a full list of WinRM configuration values for the WinRM service that the Agent Manager is to use on the remote machine, you can issue the following command and observe its output:

$ winrm get winrm/config/service

Service

RootSDDL = O:NSG:BAD:P(A;;GA;;;BA)S:P(AU;FA;GA;;;WD)(AU;SA;GWGX;;;WD)

MaxConcurrentOperations = 4294967295

MaxConcurrentOperationsPerUser = 15

EnumerationTimeoutms = 60000

MaxConnections = 25

MaxPacketRetrievalTimeSeconds = 120

AllowUnencrypted = true

CbtHardeningLevel = Relaxed

EnableCompatibilityHttpListener = false

EnableCompatibilityHttpsListener = false

CertificateThumbprint = ce 20 a6 47 d8 0d 71 b3 e2 7c dd f7 70 d9 57 d1 3f a5 65

The important properties are AllowUnencrypted (it indicates whether HTTP is allowed or not), and the Auth values that are set to true (enabled), namely Basic and Negotiate. In this example, both authentication types are enabled.

For more information on setting up for HTTPS, see About WinRM authentication and the Agent Manager .

Verwandte Dokumente

The document was helpful.

Bewertung auswählen

I easily found the information I needed.

Bewertung auswählen

Bitte w&auml;hlen Sie Ihr Produkt aus:

Damit wir Ihnen besser helfen können, geben Sie den Grund Ihres Chats an:

Empfohlene Lösungen für Ihr Problem

Foglight Agent Manager 5.9.1 - Foglight Agent Manager Guide

Configuring command-shell connection settings

About WinRM connection ports

Troubleshooting

Verifying setup

Bitte wählen Sie Ihr Produkt aus: