Chat now with support
Chat mit Support

DR Series Software 4.0 - Administrator Guide

Introducing the DR Series system documentation Introducing the DR Series system Setting up the DR Series system Configuring the DR Series system settings Managing containers Managing replications Monitoring the DR Series system Using GlobalView Configuring and using Rapid NFS and Rapid CIFS Configuring and using Rapid Data Access with NetVault Backup and with vRanger Configuring and using RDA with OST
Understanding RDA with OST Guidelines Terminology Supported RDA with OST software and components Best Practices: RDA with OST and the DR Series System Setting client-side optimization Configuring an LSU Installing the RDA with OST plug-in Configuring DR Series system information using NetBackup Backing Up Data From a DR Series System (NetBackup) Using Backup Exec with a DR Series system (Windows) Understanding the OST CLI commands Understanding RDA with OST Plug-In Diagnostic Logs Collecting Diagnostics Using a Linux Utility Guidelines for Gathering Media Server Information
Configuring and using VTL Configuring and Using Encryption at Rest Support, maintenance, and troubleshooting Supported Ports in a DR Series System

Adding an NFS or CIFS connection type container

Adding an NFS or CIFS connection type container

To add an NFS or a CIFS connection type container, complete the following steps:

1.
On the left navigation menu, select Containers, and then select or the storage group for which you want to create a container. (If you are only using the DefaultGroup storage group in your DR Series system, you do not need to select a group.)
The Containers page is displayed.
2.
In the Action menu in the upper right corner of the page, click Add Container.
The Add Container pane is displayed.
3.
For Storage Group, select the storage group to which you want to add this container. (If you are only using the DefaultGroup storage group in your DR Series system, you do not need to select a group.)
4.
For Access Protocol, select NAS (NFS, CIFS).
5.
For Container Name, type the name of the container, and then click Next.
Container names cannot exceed 32 characters in length, must start with a letter, and can be composed of any combination of the following characters:
◦
A-Z (uppercase letters)
◦
a-z (lowercase letters)
◦
0-9 (numbers). Do not start a container name with a number.
◦
dash (-) or underscore (_) special characters
 
NOTE: The DR Series system does not support the use of the following special characters in container names: /, #, or @.
6.
For Access Protocols, select NFS and CIFS as appropriate.
(Use NFS to back up UNIX or LINUX clients. Use CIFS to back up Windows clients.)
7.
For Marker Type, select the appropriate marker that supports your Data Management Application (DMA).
◦
None — Disables marker detection for the container.
◦
Auto — Automatically detects CommVault, Tivoli Storage Manager (TSM), ARCserve, and HP Data Protector marker types. In addition, select this option if you need to support EMC Networker 2.0.
◦
ARCserve—Supports the ARCserve marker.
◦
BridgeHead — Supports the BridgeHead HDM marker.
◦
CommVault—Supports the CommVault marker.
◦
HP DataProtector—Supports the HP Data Protector marker.
◦
Networker — Supports EMC Networker 3.0. If you need to support EMC Networker 2.0, select Auto.
◦
Time Navigator—Supports the Time Navigator marker.
◦
TSM—Supports the TSM marker.
◦
Unix Dump — Supports the Amanda marker, among others.
Improper marker selection can result in non-optimal savings. As a best practice, if you have only one type of DMA with traffic directed to a container, it is best to select the marker type that supports your DMA (for example, BridgeHead, Auto, or another). Conversely, as a best practice, if you have traffic from a DMA that is not one of the supported marker types, it is best to disable marker detection for the container by selecting the None marker type.
8.
Click Next.
9.
If you selected NFS as the connection type, configure NFS access as follows.
◦
NFS Options — Defines the type of access to the container. Select one of the following options.
▪
Read Write Access — To allow read-write access to the container.
▪
Read Only Access — To allow read-only access.
◦
Map Root To — Select one of the following options from the drop-down list to define the user level you want mapped to this container.
▪
Nobody — to specify a user on the system without root access permissions.
▪
Root — to specify a remote user with root access to read, write, and access files on the system.
▪
Administrator — to specify the system administrator.
◦
Client Access — Define the NFS client(s) that can access the NFS container or manage the clients that can access this container by selecting one of the following options.
▪
Open (allow all clients) — To allow open access for all clients to the NFS container you create. (Select this option only if you want to enable access for all clients to this NFS container.)
▪
Create Client Access List — To define specific clients that can access the NFS container. In the Client FQDN or IP text box, type the IP address (or FQDN hostname) and click the Add icon. The “added” client appears in the Allow Clients list box. (To delete an existing client from this list box, select the IP address (or FQDN hostname) of the client you want to delete, and click the Delete icon. The “deleted” client disappears from the list box.)
10.
If you selected CIFS as the connection type, configure CIFS access as follows.
◦
Client Access — Define the CIFS client(s) that can access the container or manage the clients that can access this container by selecting one of the following options.
▪
Open (allow all clients) — To allow open access for all clients to the container you create. (Select this option only if you want to enable access for all clients to this container.)
▪
Create Client Access List — To define specific clients that can access the container. In the Client FQDN or IP text box, type the IP address (or FQDN hostname) and click the Add icon. The “added” client appears in the Allow Clients list box. (To delete an existing client from this list box, select the IP address (or FQDN hostname) of the client you want to delete, and click the Delete icon. The “deleted” client disappears from the list box.)
 
NOTE: The DR Series system administrator that manages the system has a different set of privileges than does the CIFS administrator user. Only the DR Series system administrator can change the password for the CIFS administrator user. To change the password that allows access for the CIFS administrator user, use the authenticate --set --user administrator commands. For more information, see the DR Series System Command Line Reference Guide.
11.
Click Next.
A Configuration Summary of the options you selected for creating the container appears.
12.
Click Save.
 
 
Parent topic 

Moving data into a CIFS type container

Moving data into a CIFS type container

To move data into an existing CIFS type container, complete the following steps.

Click Start > Windows Explorer > Network.
The Network page is displayed, which lists all current computers.
2.
In the browser Address bar, click Network to select your DR Series hostname or IP address.
The Network page is displayed, which lists all current storage and replication containers.
 
NOTE: However, if your DR Series system is not listed, you can enter its hostname or IP Address preceded by "https://" and followed by the container name in the Address bar to access it (for example in this format, https://10.10.20.20/container-1). The DR Series system only supports the Hypertext Transfer Protocol Secure (HTTPS) form of IP addressing.
3.
Move data from the source location to the destination container using your regular DMA or backup application process.
 
NOTE: If any file ingested by the DR Series system by a DMA or backup application is renamed or deleted without using the DMA or backup application’s process, the corresponding catalog must be updated accordingly. Failure to do so may prevent the DMA or backup application from being able to access the data.
4.
Verify that the data recently moved now resides in the destination container.
Parent topic 

Creating an OST or RDS connection type container

Creating an OST or RDS connection type container

To create an OST or RDS connection type container, follow these steps:

On the left navigation menu, click Containers, and then select the storage group for which you want to create a container. (If you are only using the DefaultGroup storage group in your DR Series system, you do not need to select a group.)
The Containers page is displayed.
2.
In the Action menu in the upper right corner of the page, click Add Container.
The Add Container pane is displayed.
3.
For Storage Group, select the storage group to which you want to add this container. (If you are only using the DefaultGroup storage group in your DR Series system, you do not need to select a group.)
4.
For Access Protocol, select Dell Rapid Data Storage (RDS) or Symantec OpenStorage (OST) as appropriate.
5.
For Container Name, type the name of the container, and then click Next.
Container names cannot exceed 32 characters in length, must start with a letter, and can be composed of any combination of the following characters:
◦
A-Z (uppercase letters)
◦
a-z (lowercase letters)
◦
0-9 (numbers). Do not start a container name with a number.
◦
dash (-) or underscore (_) special characters
 
NOTE: The DR Series system does not support the use of the following special characters in container names: /, #, or @.
6.
If you selected Symantec OpenStorage (OST), for LSU Capacity, select one of the following options allowed per container:
◦
Unlimited — To define the allowed amount of incoming raw data per container (based on the physical capacity of the container). If you selected RDS, by default, Unlimited is selected.
◦
Quota: To define a set limit in Gibibytes (GiB) for incoming raw data allowed per container.
7.
Click Next.
A Configuration Summary of the options you selected for creating the container appears.
8.
Click Save.
Parent topic 

Creating a VTL type container

Creating a VTL type container

To create a virtual tape library (VTL) type container, complete the following steps.

 
NOTE: Only four VTL type containers can be created on a DR Series system.
1.
On the left navigation menu, select Containers, and then select the storage group for which you want to create a container. (If you are only using the DefaultGroup storage group in your DR Series system, you do not need to select a group.)
The containers page is displayed.
2.
In the Action menu in the upper right corner of the page, click Add Container.
The Add Container pane is displayed.
3.
For Storage Group, select the storage group to which you want to add this container. (If you are only using the DefaultGroup storage group in your DR Series system, you do not need to select a group.)
4.
For Access Protocol, select Virtual Tape Library (VTL).
5.
For Container Name, type the name of the container.
 
NOTE: The DR Series system does not support spaces or the following special characters in container names: /, #, or @. VTL container names cannot exceed 32 characters in length, must start with a letter, and can be composed of any combination of the following characters:
•
A-Z (uppercase letters)
•
a-z (lowercase letters)
•
0-9 (numbers). (Do not start a container name with a number.)
•
underscore (_) special characters
 
NOTE: iSCSI VTL containers do not support the following characters:
•
ASCII CONTROL CHARACTERS and SPACE through ,
•
ASCII /
•
ASCII ; through @
•
ASCII [ through `
•
ASCII { through DEL
6.
Click Next.
7.
For Robot Model, select the type of virtual tape library for the VTL container.
◦
DELL DR_L700—This is the Dell OEM version of the StorageTek L700 library.
◦
STK L700—This is the standard emulation of the StorageTek L700 library.
 
NOTE: The Dell OEM version of the VTL is supported only with Symantec Backup Exec and Netbackup data management applications (DMAs).
8.
For Tape Size, select the size of the tapes for your tape library from one of the following options.
◦
800 GB
◦
400 GB
◦
200 GB
◦
100 GB
◦
50 GB
◦
10 GB
 
NOTE: Creating a VTL container type creates a tape library of type Storage Tek L700 with 10 tape drives of type IBM Ultrium LTO-4 and 60 tape slots holding 60 tapes. Additional tapes can be added as required. For more information, see the topic later in this guide, “VTL and DR Series Specifications.”
9.
For VTL Access Protocol, select one of the following options.
◦
NDMP
◦
iSCSI
◦
FC—(This protocol is only available for the DR4300 or DR6300 systems)
◦
No Access (select this option if you are not ready to select a protocol.)
 
NOTE: The DR Series system allows you to create a VTL container type without configuring it with a specific protocol (that is, by selecting No Access). You can configure the container at a later date.
10.
For Access Control, do one of the following:
◦
If you selected NDMP as the access protocol, type the DMA’s FQDN or IP address that will access the VTL container.
◦
If you selected iSCSI as the access protocol, type the FQDN, IQN, or IP address of the iSCSI initiator that can access the VTL container.
◦
If you selected FC as the access protocol, type the port initiator WWPN for accessing the VTL container.
11.
If you selected NDMP as the access protocol, for Marker Type, select the appropriate marker that supports your DMA from one of the following options.
◦
None — Disables marker detection for the container.
◦
Unix Dump — Supports the Amanda marker, among others.
12.
If you selected iSCSI as the access protocol, for Marker Type, select the appropriate marker that supports your DMA from one of the following options.
◦
None — Disables marker detection for the container.
◦
Auto — Automatically detects CommVault, Tivoli Storage Manager (TSM), ARCserve, and HP Data Protector marker types. In addition, select this option if you need to support EMC Networker 2.0.
◦
ARCserve—Supports the ARCserve marker.
◦
BridgeHead — Supports the BridgeHead HDM marker.
◦
CommVault—Supports the CommVault marker.
◦
HP DataProtector—Supports the HP Data Protector marker.
◦
Networker — Supports EMC Networker 3.0. If you need to support EMC Networker 2.0, select Auto.
◦
TSM—Supports the TSM marker.
◦
Unix Dump — Supports the Amanda marker, among others.
 
NOTE: Improper marker selection can result in non-optimal savings. As a best practice, if you have only one type of DMA with traffic directed to a container, it is best to select the marker type that supports your DMA. Conversely, as a best practice, if you have traffic from a DMA that is not one of the supported marker types, it is best to disable marker detection for the container by selecting the None marker type.
13.
Click Next.
A Configuration Summary of the options you selected for creating the container appears.
14.
Click Save.

You can add additional tapes to the library after container creation by editing the container in the GUI or by using the CLI command:

vtl --update_carts –-name <name> --add --no_of_tapes <number>

For Fibre Channel, after a VTL is created with the default of 10 tape drives, you can add or delete drives in the library by using the following CLI command:

container --update --name <container name> --no_of_drives <1–60>
 
NOTE: For more information about using the command line interface, see the DR Series Command Line Reference Guide.
 
 
Parent topic 
Verwandte Dokumente

The document was helpful.

Bewertung auswählen

I easily found the information I needed.

Bewertung auswählen