Chat now with support
Chat mit Support

DR Series Software 4.0 - Administrator Guide

Introducing the DR Series system documentation Introducing the DR Series system Setting up the DR Series system Configuring the DR Series system settings Managing containers Managing replications Monitoring the DR Series system Using GlobalView Configuring and using Rapid NFS and Rapid CIFS Configuring and using Rapid Data Access with NetVault Backup and with vRanger Configuring and using RDA with OST
Understanding RDA with OST Guidelines Terminology Supported RDA with OST software and components Best Practices: RDA with OST and the DR Series System Setting client-side optimization Configuring an LSU Installing the RDA with OST plug-in Configuring DR Series system information using NetBackup Backing Up Data From a DR Series System (NetBackup) Using Backup Exec with a DR Series system (Windows) Understanding the OST CLI commands Understanding RDA with OST Plug-In Diagnostic Logs Collecting Diagnostics Using a Linux Utility Guidelines for Gathering Media Server Information
Configuring and using VTL Configuring and Using Encryption at Rest Support, maintenance, and troubleshooting Supported Ports in a DR Series System
The System Configuration page is displayed.
2.
In the Action menu in the upper right corner of the page, click Configuration Wizard.
3.
Click Next or Previous to navigate through the Configuration Wizard steps. Refer to the topics in this System Configuration chapter for more detailed instructions on completing these steps.
a.
Reset Password Setup & Change Admin Password
b.
Fill in Admin Contact Information & Email Relay Host
c.
Set the hostname, DNS, and IP Mode.
d.
Join Active Directory (as needed).
e.
Review the Initial Upgrade Message.
You should verify that your system has the latest available updates. Visit support.quest.com/dr-series, and navigate to the Software Downloads page for your specific DR Series model to download the latest upgrade file. Before upgrading, you should exit the Configuration Wizard and then proceed to the DR Series system GUI Support > Software Upgrade page. See the topic “Upgrading the DR Series System Software” in the “Support, Maintenance, and Troubleshooting” chapter later in this guide for detailed instructions on upgrading the software.
When you click Next on the final page of the Configuration Wizard, a dialog box is displayed confirming that you have completed the initial configuration of your system.
4.
In the dialog box, click OK. The Dashboard page is displayed.
Parent topic 

Registering with the Support Portal

Registering with the Support Portal

You can now register your DR Series system with the Quest Support Portal by using the DR Series system CLI system --support_agent set of commands. The registered DR Series system will collect certain information that it will transmit to Quest Support. Such information can include operational statistics, performance metrics, diagnostic information and configuration settings of the DR Series system. This enables support personnel to monitor and capture information to proactively help troubleshoot issues with your system.

Parent topic 

Configuring Active Directory settings

Configuring Active Directory settings

Removing a login group

You can easily join the DR Series system to your Microsoft Active Directory Services (ADS) domain. This topic describes how to configure Active Directory (AD) settings for the DR Series system, which requires that you direct your DR Series system to join or leave a domain that contains a Microsoft Active Directory Service (ADS). Instructions are provided below to join an ADS domain or to leave an ADS domain. When you join the DR Series system to an ADS domain, this disables the Network Time Protocol (NTP) service and instead uses the domain-based time service.

To configure the DR Series system for a domain using ADS, complete the following steps:

1.
In the left navigation menu, click System Configuration > Active Directory.
The Active Directory page is displayed.
2.
Do one of the following:
◦
On the Active Directory page, click the Join link.
◦
On the Action menu, click Join.
The Join pane is displayed.
3.
Enter the following AD logon information:
◦
Domain Name (FQDN)—Enter a fully qualified domain name for the ADS; for example, AD12.acme.com. (This is a required field.)
 
NOTE: Supported domain names are limited to 64 characters in length and can only consist of a combination of A-Z, a-z, 0-9, and three special characters: a dash (-), a period (.), and an underscore (_).
◦
Username—Enter a valid user name that meets the user name guidelines for the ADS. (This is a required field.)
 
NOTE: Supported user names are limited to 64 characters in length and can only consist of a combination of A-Z, a-z, 0-9, and three special characters: a dash (-), a period (.), and an underscore (_).
◦
Password—Enter a valid password that meets the password guidelines for the ADS. (This is a required field.)
◦
Org Unit—Enter a valid organizational name that meets the organization name guidelines for the ADS. (This is an optional field.)
4.
Click Join.
The Domain name and login group will appear on the Active Directory page if successfully added.
5.
To leave an ADS domain, in the Action menu in the upper right corner of the page, click Leave.
a.
In the Leave Active Directory pane, enter the username and password for the ADS domain.
b.
Click Leave.
 
 
Parent topic 

Adding a login group to an ADS domain

Adding a login group to an ADS domain

After you configure your DR systems within the same ADS domain, you must ensure that a login group exists and add it to the domain.

Adding a login group is only possible when the DR Series system is joined to a domain. Also, you must be logged in as a domain user that is part of an enabled login group.

To add a login group in an ADS domain, complete the following steps:

On the left navigation menu, click System Configuration > Active Directory.
The Active Directory page is displayed.
2.
In the Action menu in the upper right corner of the page, click Add Login Group.
3.
In the Add Login Group pane, type the name of the login group including the domain name; for example, Domain\Domain Admins. If your login group name contains spaces, you must not enclose it in quotation marks. (This differs from the equivalent CLI command.)
4.
Click Add Login Group to add the login group.
 
NOTE: Changes made to the login group take effect on the next log in attempt (unlike Windows ADS, no active checking is done on the group).
Parent topic 
Verwandte Dokumente

The document was helpful.

Bewertung auswählen

I easily found the information I needed.

Bewertung auswählen