立即与支持人员聊天
与支持团队交流

NetVault Plug-in for Oracle 7.1 - User Guide

Introducing Dell™ NetVault™ Backup Plug‑in for Oracle® Defining a backup strategy Installing and removing the plug-in Configuring the plug-in Backing up data Using the Oracle Flashback Database Restoring data
Restoring and recovering data – an overview Performing User Managed restores Using advanced User Managed restore procedures Performing RMAN restores Using RMAN types of recovery in a non-RAC environment Using advanced procedures with RMAN restores
Maintaining the Recovery Catalog Using the RMAN CLI Using the Plug-in with Oracle RAC Using the Plug-inin a failover cluster environment Using the plug-in with Oracle Data Guard Troubleshooting Glossary About Dell

Viewing Flashback Database status

To view database details about a previously configured database ,  including whether FRA and Flashback Database are enabled 
1
In the Navigation Pane, click Create Backup Job, and click Create New next to the Selections list.
2
In the selection tree, open the applicable client node.
3
Double-click Plug‑in for Oracle, and select the applicable database.
4
From the Actions list, select View Details.
The Details dialog includes the following details:
•
Flash Recovery Area Destination – When FRA is enabled, displays the destination of the FRA.
•
Flashback Database Enabled – Indicates YES if the Flashback Database feature is enabled or NO if not.
Additionally, backups done with plug-in will show a Flashback Database node for the plug-in on the Create Selection Set page when you create a restore job. The Flashback Database node lets you perform a Flashback Database instead of a restore or recovery.
5
Click OK to close the dialog.

Flashback Database options

Selecting Flashback Database in the plug-in is equivalent to the RMAN or SQL FLASHBACK DATABASE command.
Flashback Database has the following options:
•
To Restore Point – Flashes the database to a specific restore point. A restore point is a named point-in-time that can be used as a flashback target. When you create a restore point, you are essentially naming the current System Change Number (SCN). You can create up to 2048 named restore points and these can either be normal or guaranteed. A guaranteed restore point is used in a Flashback Database.
Restore points can be created using the CREATE RESTORE POINT command. For more information, refer to Creating Normal and Guaranteed Restore Points in the Oracle Database Backup and Recovery User’s Guide.
•
To Time – Reverts the database back to its state at the time specified.
•
To SCN – Reverts the database back to its state at the specified SCN.
•
Before Time – Reverts the database back to its state one second before the specified timestamp.
•
Before SCN – Reverts the database back to its state at the system change number just preceding the specified SCN.
•
Before Reset Logs (available for Oracle 10.2.x and later versions only) – Rewinds the database back to the SCN just before the RESETLOGS happened.

Flashback Database restrictions

There are two restrictions on selecting Flashback Database:
•
Whole Database and Flashback Database nodes cannot be selected at the same time. If selected, the restore job fails and the NetVault Backup binary logs show an error message:
Cannot select 'Whole Database' and 'Flashback Database' at the same time.
•
On the Create Selection Set page, Flashback Database cannot be selected at the same time as other nodes such as Parameter File, Control Files, Tablespaces, and Datafiles. If selected, the restore job will fail and the NetVault Backup binary logs will show an error message:
Restore Selections Error. Cannot select 'Flashback Database' and Individual Datafiles at the same time.

Restoring data with the plug-in and Flashback Database

To execute Flashback Database
1
In the Navigation pane, click Create Restore Job.
2
On the Create Restore Job - Choose Saveset page, select Plug‑in for Oracle from the Plugin Type list.
3
To filter the items displayed in the saveset table further, use the Client, Date, and Job ID lists.
4
In the saveset table, select any RMAN-based backup saveset, and click Next.
5
On the Create Selection Set page, select the Flashback Database node.
6
Click Edit Plugin Options, and then click the Restore Options tab.
7
Select Whole Database Restore, Mount Database Before Restore, and Shutdown Abort Database First.
 
 
*NOTE: The database must be in a mounted state to perform a Flashback Database.
8
On the Post Recovery tab, select Open Database after Recovery and Read Write and Reset Logs.
9
On the Flashback Database tab, select the applicable Flashback Point Type.
For example, select To Time, and input the time to which the database should be flashed back.
10
Click Ok to save the settings, and then click Next.
11
In Job Name, specify a name for the job if you do not want to use the default setting.
12
In the Target Client list, select the machine on which you want to restore the data.
13
Use the Schedule, Source Options, and Advanced Options lists to configure the any additional required options.
14
Click Submit to submit the job for scheduling.
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级