立即与支持人员聊天
与支持团队交流

DR Series Software 4.0 - Command Line Reference Guide

Introduction to the DR Series System Command Line Reference Guide Introducing the DR Series system Managing the DR Series system
Alerts Commands Authenticate Commands Network
Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --disable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help
OST RDA Stats Storage Group commands System
System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --support_agent --register system --support_agent --unregister system --support_agent --stats system --support_agent --status system --help
User Virtual Machine
Maintaining the DR Series System
Diagnostics Maintenance
Maintenance Command Usage maintenance --filesystem [--start_scan [verify_data | verify_rda_metadata | verify_metadata] [--storage_group <name>] maintenance --filesystem [--stop_scan] maintenance --filesystem [--scan_status] maintenance --filesystem [--scan_report [verbose]] maintenance --filesystem [--repair_status [verbose]] maintenance --filesystem [--repair_history [verbose]] maintenance --filesystem [--scan_restart [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--repair_now] maintenance --filesystem [--reclaim_space] maintenance --filesystem [--stop_reclaim_space] maintenance --filesystem [--clear_quarantine] maintenance --filesystem --show_throughput maintenance --configuration [--backup] maintenance --configuration [--restore] maintenance --configuration [--reinit_dictionary] maintenance --configuration [--reset_web_certificate] maintenance --hardware [--reinit_nvram] maintenance --hardware [--restore_hw_db] maintenance --hardware [--motherboard_replaced] maintenance --disk [--make_standby [slot num]] [--type <internal | external-<num> | service tag>] --clear_foreign] maintenance --remote_access [--show] maintenance --remote_access [--enable] maintenance --remote_access [--racreset] maintenance --remote_access [--static_ip] [--ip <IPv4/IPv6 address>] [--netmask <netmask>] [--gateway <IPv4/IPv6 address>] [--device <lom1|lom2|lom3|lom4>] maintenance --remote access [--disable] maintenance --vdisk --check_consistency --type <boot|internal|external> [--service_tag <service tag>] maintenance --help
Managing DR Series System Storage Operations
System Storage Operation Commands Connection Container VTL NDMP iSCSI FC Replication Seed Schedule
Data Integrity Checking Additional Linux Commands

replication --add --name <name> --role <source | target> --peer <ip address | hostname> [--peer_name <name>] [--peer_group_name <name>] [--replication_traffic <ip address | hostname>] [--encryption <none | aes128 | aes256>][--username <user name>]

Syntax

replication --add --name backup --role source --peer 10.250.240.192 --encryption aes128

Result

Enter password foradministrator@10.250.240.192:
Replication entry created successfully.
Replication Container          : backup
Replication Role               : Source
Replication Target             : 10.250.240.192
Replication Target IP          : 10.250.240.192
Replication Target Mgmt Name   : 10.250.240.192
Replication Target Mgmt IP     : 10.250.240.192
Replication Local Data Name    : DR2K-01
Replication Local Data IP      : 10.250.208.232
Replication Target Container   : backup
Replication Enabled            : Yes
Replication Compression Enabled: Yes
Replication Encryption         : AES 128-bit
Note: To verify that you have successful added a replication link to the DR Series system (or to view the current status of existing containers), see replication --show.

replication --update --name <name> --role <source | target> [--peer <ip address | hostname>] [--encryption <none | aes128 | aes256>] [--username <user name>]

Syntax

replication --update --name backup --role source --peer 10.25.19.5

Result

Note: If you attempt to update a container that already has replication enabled, this displays the following message:
Replication on backup is enabled and cannot be updated, please stop it first.

When replication is enabled on the container, you must first disable it before you can update it. To disable replication on a container, enter the DR Series system CLI replication --stop command and define the container name and role:

replication --stop --name <name> --role <source | target>
Note: For more information about disabling replication, see replication --stop --name <name> --role <source | target>.

Disables replication on a container:

replication --stop --name backup --role source
Replication configuration updated successfully.
Replication Container           : backup
Replication Role                : Source
Replication Target System       : acme-85
Replication Target System IP    : 10.25.192.5
Replication Target Container    : acme85-S2
Replication Enabled             : No
Replication Compression Enabled : Yes
Replication Encryption          : AES 128-bit

replication --delete --name <name> --role <source | target> [--force]

Syntax

replication --delete --name acme-59-replica --role target

If you attempt to delete a container that already has replication enabled, this displays the following message:

Replication on acme-59-replica is enabled and cannot be deleted, please stop it first.
Note: If the replication state of the link is enabled, you must use the replication --stop command to disable replication before you can delete the replication link. For more information, see replication --stop --name <name> --role <source | target>.

Deletes the existing replication link to a container.

replication --delete --name acme-59-replica --role source

Result

Successfully deleted replication entry.
Note: The DR Series system CLI --force command is optional, and this command allows you to force the deletion of an existing replication link (such as when communications between the source and target are not working).

replication --start --name <name> --role <source | target>

Syntax

replication --start --name container2_replica --role target

Result

Replication configuration updated successfully.
Replication Container           : container2_replica
Replication Role                : Source
Replication Target System       : acme-85
Replication Target System IP    : 10.20.22.20
Replication Target Container    : acme85-S2
Replication Enabled             : Yes
Replication Compression Enabled : Yes
Replication Encryption          : AES 128-bit
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级