立即与支持人员聊天
与支持团队交流

DR Series Software 3.2.6 - Administrator Guide

Introduction to the DR Series System Documentation Understanding the DR Series System Setting Up the DR Series System Hardware Configuring the DR Series System Settings Managing DR Series Storage Operations Monitoring the DR Series System Using Global View Using the DR Series System Support Options Configuring and Using Rapid NFS and Rapid CIFS Configuring and Using Rapid Data Access with Dell NetVault Backup and with Dell vRanger Configuring and Using RDA with OST
Understanding RDA with OST Guidelines Terminology Supported RDA with OST Software and Components Best Practices: RDA with OST and the DR Series System Setting Client-Side Optimization Configuring an LSU Installing the RDA with OST Plug-In Configuring DR Series System Information Using NetBackup Backing Up Data From a DR Series System (NetBackup) Using Backup Exec With a DR Series System (Windows) Understanding the OST CLI Commands Understanding RDA with OST Plug-In Diagnostic Logs Collecting Diagnostics Using a Linux Utility Guidelines for Gathering Media Server Information
Configuring and Using VTL Configuring and Using Encryption at Rest Troubleshooting and Maintenance Supported Ports in a DR Series System Getting Help
◦
Chunk data and perform hash computation on the client; transfer chunked hash files on the back-end
◦
Reduce the amount of data that must be written across the wire
•
Improve performance
•
Support DMAs such as CommVault, EMC Networker, and Tivoli Storage Manager. For the current list of supported DMAs, see the Dell DR Series System Interoperability Guide.
•
Compatible with existing NFS and CIFS clients — just need to install a plug-in (driver) on the client
◦
Can use Rapid NFS and Rapid CIFS to accelerate I/O operations on any client — including a client that uses home-grown backup scripts
◦
Can service multiple and concurrent media server backups
Parent topic 

Best Practices: Rapid NFS

Best Practices: Rapid NFS

This topic introduces some recommended best practices for using Rapid NFS operations with the DR Series system.

RDA containers cannot use Rapid NFS. If you have existing NFS/CIFS containers, you do not need to create new containers to use Rapid NFS; you can install the plug-in (driver) to existing clients.
The Rapid NFS plug-in (driver) must be installed on client systems
After the plug-in is installed, write operations will go through Rapid NFS while metadata operations such as file creates and permission changes will go through the standard NFS protocol. Rapid NFS can be disabled by uninstalling the plug-in.
Markers must be set on the client, not in the DR Series GUI
If you are using a DMA that supports a marker, should explicitly set it. Your containers should have the marker type of None until you set the marker using the Mount command on the client (after installing the Rapid NFS plug-in). For existing containers, re-set the marker using the procedure that follows.
For example, if you wanted to set the CommVault marker (cv):
mount -t rdnfs 10.222.322.190:/containers/backup /mnt/backup -o marker=cv
Mount command usage:
rdnfs [nfs mount point] [roach mount point] -o marker=[marker]
where:
nfs mount point = Already mounted nfs mountpoint
roach mount point = A new mount point
marker = appassure, arcserve, auto, cv, dump, hdm, hpdp, nw, or tsm
Your DR Series system must meet the minimum configuration
Rapid NFS is available on a DR Series system and a client with a minimum of 4 CPU cores running at a minimum of 4 GHz cumulative processing power and 2 GB memory. Kernels must be 2.6.14 or later. For a list of supported operating systems, see the Dell DR Series System Interoperability Guide.
If you update your operating system, you must update your Rapid NFS plug-in as well. Updates are available on the Support site as well as within the GUI on the Clients page.
Rapid NFS is stateful
If the DR Series system goes down, the connection will terminate. DMAs will restart from the last checkpoint.
Rapid NFS and passthrough mode
If Rapid NFS mode fails for any reason, the DR Series system falls back to regular NFS mode automatically. For details, see Monitoring Performance.
Rapid NFS performance considerations
When using Rapid NFS on your client, Dell recommends that you do not run other protocols to the DR in parallel, as this will adversely affect your overall performance.
Rapid NFS acceleration constraints
Rapid NFS does not support:
◦
Direct I/O memory
◦
Mapped files
◦
File path size greater than 4096 characters
◦
File write locks across clients
 
NOTE: If the client and server do not have the same times, the times seen will not match typical NFS behavior due to the nature of file system in user space (FUSE).
Parent topic 

Best Practices: Rapid CIFS

Best Practices: Rapid CIFS

This topic introduces some recommended best practices for using Rapid CIFS operations with the DR Series system.

RDA containers cannot use Rapid CIFS. If you have existing NFS/CIFS containers, you do not need to create new containers to use Rapid CIFS; you can install the plug-in (driver) to existing clients.
The Rapid CIFS plug-in (driver) must be installed on client systems
After the plug-in is installed, write operations will go through Rapid CIFS while metadata operations such as file creates and permission changes will go through the standard CIFS protocol. Rapid CIFS can be disabled by uninstalling the plug-in.
Your DR Series system must meet the minimum configuration
Rapid CIFS is available with a DR Series system and a client with a minimum of 4 CPU cores running at a minimum of 4 GHz cumulative processing power and 2 GB memory. For a list of supported operating systems, see the Dell DR Series System Interoperability Guide.
If you update your operating system, you must update your Rapid CIFS plug-in as well. Updates are available on the Support site as well as within the GUI on the Clients page.
Rapid CIFS is stateful
If the DR Series system goes down, the connection will terminate. DMAs will restart from the last checkpoint.
Rapid CIFS and passthrough mode
If Rapid CIFS mode fails for any reason, the DR Series system falls back to regular CIFS mode automatically. For details, see Monitoring Performance.
Rapid CIFS acceleration constraints
Rapid CIFS does not support:
◦
NAS functionality
▪
Optlocks (but supported if a single client is writing)
▪
Byte-range locks
◦
Optimization of very small files (less than 10 MB). File size can be adjusted using configuration settings.
◦
FILE_NO_IMMEDIATE_BUFFERING and FILEWRITE_THROUGH operations (sent via CIFS only).
◦
File path size greater than 4096 characters
Parent topic 

Setting Client-Side Optimization

Setting Client-Side Optimization

Client-side optimization (also known as client-side deduplication) is a process that can contribute to saving time performing backup operations and reducing the data transfer overhead on the network.

To configure dedupe/passthrough before the client makes a connection, you need to use the DR Series system command line interface (CLI).

NOTE: To update a client in the DR Series system GUI, the client must already be attached (and therefore enabled to appear in the GUI). If a client connection exists, you can select the radio button in the GUI to modify it.

You can turn On or turn Off client-side optimization by using the CLI commands, rda --update_client --name --mode. For more information about DR Series system CLI commands, see the Dell DR Series System Command Line Reference Guide located at dell.com/powervaultmanuals (by selecting your particular DR Series system).

Parent topic 
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级