立即与支持人员聊天
与支持团队交流

vRanger 7.8 - User Guide

Introduction Configuring vRanger
Configuration overview Configuring vRanger through the Startup Wizard Configuring vRanger manually Supplemental instructions: additional repository types
Using vRanger Backup Restore Replicate VMs Reports Integrating and monitoring vRanger Using the vRanger Console vAPI Cmdlet details
Add-BackupGroupEntity Add-BackupJobTemplate Add-CIFSRepository Add-DdbReplicationRepository Add-DdbRepository Add-EsxHost Add-HypervCluster Add-HypervHost Add-HypervRestoreJobTemplate Add-NFSRepository Add-NVSDRepository Add-PhysicalMachine Add-RdaRepository Add-ReplicationJobTemplate Add-RestoreFromManifestJobTemplate Add-RestoreJobTemplate Add-VirtualAppforLinuxFLR Add-VirtualAppforLinuxFLRVA Add-VirtualCenter Disable-Job Dismount-LinuxVolume Enable-Job Get-AddressBook Get-BackupGroupEntity Get-CatalogSearchData Get-CatalogStatus Get-ConfigOption Get-Connection Get-CurrentTemplateVersionID Get-Datastore Get-GlobalTransportFailover Get-InventoryEntity Get-IsInventoryRefreshing Get-Job Get-JobTemplate Get-MonitorLog Get-Network Get-PhysicalMachineDiskMap Get-Repository Get-RepositoryJob Get-RepositorySavePoint Get-RestoreDiskMap Get-SavepointDisk Get-SavepointManifest Get-Savepoints Get-TransportFailover Get-VirtualApplianceConfig Get-VirtualApplianceDeploymentStatus Get-VirtualApplianceReconfigStatus Get-VirtualMachinesUnderInventory Get-VmDisk Get-VMDKVolume Install-VirtualAppliance Mount-LinuxVolume New-BackupFlag New-BackupGroupMember New-Daily Schedule New-EmailAddress New-IntervalSchedule New-MonthlySchedule New-ReplicationFlag New-RestoreFlag New-SMTPServer New-TransportConfiguration New-VirtualAppliance New-WeeklySchedule New-YearlySchedule Remove-AllMount Remove-BackupGroupEntity Remove-BackupGroupMember Remove-Catalog Remove-DdbStorageUnit Remove-JobTemplate Remove-LinuxVolume Remove-Repository Remove-SavePoint Remove-VirtualAppliance Remove-VirtualApplianceConfiguration Run-JobsNow Run-ReplicationFailover Run-ResumeReplicationFailover Run-TestReplicationFailover Set-Cataloging Set-CBTonVM Set-LinuxVolume Set-MountPath Set-Resources Stop-vRangerJob Update-BackupJobTemplate Update-GlobalTransportFailover Update-HypervRestoreJobTemplate Update-Inventory Update-ReplicationJobTemplate Update-RestoreJobTemplate Update-VirtualAppliance Update-VirtualApplianceConfiguration
About us

Performing optional configurations

Previous Next


Backup > Performing optional configurations

Enabling VMware Changed Block Tracking (CBT)

Previous Next


Backup > Performing optional configurations > Enabling VMware Changed Block Tracking (CBT)

VMware® CBT reduces the time needed for incremental and differential backups by only backing up the portions of a disk that have changed since the last backup. By determining which blocks changed within the VMDK file, vRanger only backs up the portions of a disk that have changed since the last backup. This often results in shorter backup operations, and reduced resource consumption on network and storage elements.
VMware vSphere® supports CBT, and most VMs running in this environment can use it. The VMs must be Hardware Version 7 or later, and have been created and hosted in VMware® ESXi™ 5.0 or later hosts. VMs that are created in VMware® ESX® 4 or earlier must be migrated to Hardware Version 7 or later for CBT to be supported. CBT must be enabled for each VM with which CBT is to be used.
In the Options Selection page of the vRanger Backup Wizard, select Enable Change Block Tracking.
In the My Inventory view, right-click the VM for which want to change the CBT setting, and then select Enable Change Tracking. The Changed Block Tracking Icon appears next to any VM on which CBT is enabled.

Adding a custom backup group

Previous Next


Backup > Performing optional configurations > Adding a custom backup group

This feature lets you organize physical servers, Hyper-V® servers, or VMware® vCenter™ objects — VMs, hosts, and folders — into groups, which lets you create a backup job for only the selected nodes. This feature provides additional flexibility for creating backup jobs.
IMPORTANT: A backup group must contain only physical objects, only Hyper-V objects, or only VMware® objects. You cannot combine VMware, Hyper-V, and physical objects into a single backup group.
1
In the My Inventory view, select the VMware, Hyper-V, or Physical tab.
Click the Add Icon, and select Backup Group.
Expand the Backup Group panel in the Inventory pane. Right-click an empty spot, select Add, and then click Backup Group.
3
Enter a name for the Backup Group, and click to select the nodes to include in the group.
4
Click Add.

Configuring VSS tools for VMware VMs

Previous Next


Backup > Performing optional configurations > Configuring VSS tools for VMware VMs

VSS Tools are only available for VMware® VMs and do not apply to Hyper-V® VMs or physical machines.
In addition to the standard quiescing implementation using VMware® Tools, vRanger provides an optional method for application quiescing on VMware VMs. This optional method uses a small executable tool — vzShadow.exe — deployed to the source VM and is enabled by VMware Tools during quiescing. The vRanger VSS Tools must be deployed to each VM for which you need application-consistent backups. For more information, see Application consistency for virtual backups.
1
When viewing the My Inventory View, right-click the preferred VM, and select Configure VSS Tools.
2
When the Configure VSS Tools dialog box appears, enter the name and password for an account with administrative privileges on the VM, and click Next.
4
If preferred, select Perform application log truncation.
5
Click Configure, and click Next.
Creates the C:\Program Files\Quest\vRanger\VSS directory, and populate the directory with the vzShadow executable and supporting files.
Creates the C:\Program Files\VMware\VMware Tools\backupscripts.d directory, and creates a freeze.bat file in that directory that contains the appropriate contents based on your selections.
1
When viewing the My Inventory View, right-click the preferred VM, and select Configure VSS Tools.
2
When the Configure VSS Tools dialog box appears, enter the name and password for an account with administrative privileges on the VM, and click Next.
3
Click Remove.
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级