Chat now with support
Chat with Support

vRanger 7.7.1 - User Guide

Introduction Configuring vRanger
Configuring vRanger through the Startup Wizard Configuring vRanger manually Supplemental instructions: additional repository types
Using vRanger Backup Restore
Restoring a physical server Performing a full restore for VMware VMs Performing a full restore for Hyper-V® VMs Performing a full restore for VMware vApps Performing a full restore of a physical machine Performing an FLR on Windows Performing an FLR on Linux Restoring from manifest
Replicate VMs Reports Integrating and monitoring vRanger Using the vRanger Console vAPI Cmdlet details
Add-BackupJobTemplate Add-CIFSRepository Add-DdbReplicationRepository Add-DdbRepository Add-EsxHost Add-HypervCluster Add-HypervHost Add-HypervRestoreJobTemplate Add-NFSRepository Add-NVSDRepository Add-PhysicalMachine Add-RdaRepository Add-ReplicationJobTemplate Add-RestoreFromManifestJobTemplate Add-RestoreJobTemplate Add-VirtualAppforLinuxFLR Add-VirtualAppforLinuxFLRVA Add-VirtualCenter Disable-Job Dismount-LinuxVolume Enable-Job Get-AddressBook Get-BackupGroupEntity Get-CatalogSearchData Get-CatalogStatus Get-ConfigOption Get-Connection Get-CurrentTemplateVersionID Get-Datastore Get-GlobalTransportFailover Get-InventoryEntities Get-IsInventoryRefreshing Get-Job Get-JobTemplate Get-MonitorLog Get-Network Get-PhysicalMachineDiskMap Get-Repository Get-RepositoryJob Get-RepositorySavePoint Get-RestoreDiskMap Get-SavepointDisk Get-SavepointManifest Get-Savepoints Get-TransportFailover Get-VirtualApplianceConfig Get-VirtualApplianceDeploymentStatus Get-VirtualApplianceReconfigStatus Get-VirtualMachinesUnderInventory Get-VmDisk Get-VMDKVolume Install-VirtualAppliance Mount-LinuxVolume New-BackupFlag New-BackupGroupMember New-Daily Schedule New-EmailAddress New-IntervalSchedule New-MonthlySchedule New-ReplicationFlag New-RestoreFlag New-SMTPServer New-TransportConfiguration New-VirtualAppliance New-WeeklySchedule New-YearlySchedule Remove-AllMount Remove-BackupGroupEntity Remove-BackupGroupMember Remove-Catalog Remove-DdbStorageUnit Remove-JobTemplate Remove-LinuxVolume Remove-Repository Remove-SavePoint Remove-VirtualAppliance Remove-VirtualApplianceConfiguration Run-JobsNow Run-ReplicationFailover Run-ResumeReplicationFailover Run-TestReplicationFailover Set-Cataloging Set-CBTonVM Set-LinuxVolume Set-MountPath Set-Resources Stop-vRangerJob Update-BackupJobTemplate Update-GlobalTransportFailover Update-HypervRestoreJobTemplate Update-Inventory Update-ReplicationJobTemplate Update-RestoreJobTemplate Update-VirtualAppliance Update-VirtualApplianceConfiguration
About us

Removing an email address

Previous Next



Removing an email address

Complete the steps in the following procedure to remove an email address from vRanger.

To remove an email address:
1
2
Under the General node on the Configuration Options page, click Email Configuration.
3
In the Email Addresses section, select the email address that you want to delete.
4
Click Remove.

The listing is deleted.

5
Click OK.

Configuring display language

Previous Next


Configuring vRanger > Configuring vRanger manually > Configuring display language

Configuring display language

vRanger lets you configure the language used when displaying the vRanger UI.

To configure display language:
1
2
Under the General node in the Configuration Options dialog box, click Language.
3
From the Available Languages drop-down list, select the language to be used.

If preferred, select based on system locale to make an automatic setting based on the vRanger machine’s locale setting.

4
Click OK.

Configuring a virtual appliance (VA)

Previous Next


Configuring vRanger > Configuring vRanger manually > Configuring a virtual appliance (VA)

Configuring a virtual appliance (VA)

vRanger uses a VA for Linux® FLR, standard backup and restore, and for replication to and from VMware® ESXi™ servers. The Virtual Appliance Configuration dialog box lets you add a configured VA to vRanger, and select the VA to use for Linux FLR. VAs deployed using the Virtual Appliance Deployment Wizard is added to vRanger automatically.

To configure a VA:
1
In the Configuration Options dialog box, select Virtual Appliance Configuration.
2
Click Add.

The Add virtual appliance configuration dialog box appears, showing the vCenter inventory tree.

The VA appears in the Deployed Virtual Appliances section.

Importing a license file

Previous Next



Importing a license file

Before you start this process, confirm that you have placed your license file in a location that you can reach easily.

To import a license file:
1
2
Under the Licensing node in the Configuration Options dialog box, click Product.
3
Click Add New License.

The new license information is added to the dialog box.

5
Click Apply.

The dialog box refreshes with the new license information added.

6
Related Documents

The document was helpful.

Select Rating

I easily found the information I needed.

Select Rating