지금 지원 담당자와 채팅
지원 담당자와 채팅

NetVault Plug-in for VMware 12.2 - User Guide

Introducing NetVault Backup Plug-in for VMware Installing the plug-in Configuring the plug-in Defining a backup strategy Using the image-level backup method Using the file-level backup method Restoring image-level backups Restoring file-level backups Troubleshooting

Performing file-level backups

1
In the Navigation pane, click Create Backup Job to start the configuration wizard.
In the Navigation pane, click Guided Configuration, and then on the NetVault Configuration Wizard page, click Create Backup Jobs.
2
In Job Name, specify a name for the job.
3
In the Selections list, select an existing Backup Selection Set, or complete the following steps to create a set:
a
To open the NetVault Backup Selections page, click Create New.
Hosts and Clusters Inventory View: To display the available virtual machines, open the Datacenter, Cluster, Resource Pool, and other nodes.
VMs and Templates View: To display the available virtual machines, open the Datacenter and folder nodes.
d
A folder is created in the Working Directory (set in the Configure dialog box). This folder is assigned the same name as the selected virtual machine.
A Drives node is added to the selections tree. This node is displayed under selected virtual machine.
NOTE: If the boot disk is not the first disk among the disks attached to a virtual machine when they are arranged in the controller:device order (that is, ide0:0, ide0:1, scsi0:0, scsi0:1, and so on), the mounting operation might fail for the virtual machine.
g
Click Save, and in the Create New Set dialog box, type a name for the set.
4
In the Plugin Options list, select an existing Backup Options Set, or complete the following steps to create a set:
IMPORTANT: On Windows, when you create a Backup Options Set for file-level backups, you must use the default set “Default Backup Options for 'File System' — VMware Plugin - Windows” as the template. If you use any other set as the template, the backup may fail.
a
To open the File System Plugin Backup Options page, click Create New.

Backup Type

Select the applicable option from the following:

For more information about file-level backup types, see File-level backups.

Create Dump Type Backup

To create Dump Type Incremental or Differential Backups, select this check box. With these backups, you can only restore those files that were backed up in a particular Incremental or Differential Backup.

Check For Files Being Modified During Backup

To mark the files that are being modified during a backup as “in flux,” leave this check box selected. During restore, these files are not restored by default. To restore these files, you must set the option Restore Files Modified During Backup on the Restore Options Set.

If you do not want to check for files that are being updated during backup, clear this check box.

Enable Restartable Backup

To add the ability to stop a job and resume it later from that point, select this check box.

When you stop the job, the plug-in generates an index for all items that have been processed up to that point and writes the index to the backup media and NetVault Database. When you restart the job later, the plug-in runs an Incremental Backup job to back up the remaining files and folders.

You can stop and resume a job from the Job Status page. For more information, see the Quest NetVault Backup Plug-in for FileSystem User’s Guide.

Path to Backup Log

To generate a backup log file, type the filename. The log provides a list of files that are selected for the backup. The files that are backed up successfully are marked with an “o” and the others are marked with an “x.” You can use this option with an Incremental Backup to determine which new or changed files have been backed up. If you specify an existing filename, the plug-in overwrites the file. The log file is created in CSV file format, and includes details such as file size, date modified, and file type.

c
Click Save, and in the Create New Set dialog box, type a name for the set.
For more information about these sets, see the Quest NetVault Backup Administrator’s Guide.
To save the job definition without scheduling it, click Save. You can view, edit, or run this job from the Manage Job Definitions page. This job is not displayed on the Job Status page until you submit it.
You can monitor the job progress from the Job Status page and view the logs from the View Logs page.
For more information about Job Status, View Logs, and Manage Job Definitions, see the Quest NetVault Backup Administrator’s Guide.

Backup selection tree icons

vCenter Server

Datacenter Server

ESXi Server Cluster

Closed folder

Open folder

ESXi Server

ESXi Server in maintenance mode

Inaccessible ESXi Server

Virtual Appliance (vApp)

Resource pool

Virtual machine (turned on)

Inaccessible virtual machine

Mounted virtual machine

Suspended virtual machine

Turned off virtual machine

Virtual machine (turned on, CBT enabled)

Inaccessible virtual machine (CBT enabled)

Mounted virtual machine (CBT enabled)

Suspended virtual machine (CBT enabled)

Turned off virtual machine (CBT enabled)

Primary virtual machine (turned on) in a Fault Tolerant group

Inaccessible primary virtual machine

Suspended primary virtual machine

Turned off primary virtual machine

Secondary virtual machine in a Fault Tolerant group

Inaccessible secondary virtual machine

Suspended secondary virtual machine

Turned off secondary virtual machine

Removing the snapshot and mount folder manually

When you mount a virtual machine for file-level backup or browse operation, the following events occur:

The plug-in creates a snapshot named “BKB_SNAP” on the virtual machine.

When you unmount the virtual machine, the cleanup process automatically removes the mount folder and snapshot. In a normal scenario, do not remove them manually.

If the plug-in fails to remove the mount folder or snapshot for any reason, a subsequent mount operation for the same virtual machine fails and the error message “A stale mount was found” is displayed. For example, if the plug-in exits unexpectedly after mounting a virtual machine, the snapshot and mount folder are not removed. In this scenario, you must manually remove them. You must also complete these steps if a snapshot is deleted manually while a virtual machine is still mounted.

1
If the Working Directory contains the mount folder for the virtual machine, remove it.
2
If you were using an advanced transport mode, such as san or hotadd, navigate to the <system_drive>/windows/temp/vmware-system directory.
3
Here <VM_UUID> is the universally unique identifier (UUID) of the mounted virtual machine and VM_moref is an internal reference that the ESXi or vCenter Server uses to see the virtual machine. To delete this folder, you may be required to set necessary permissions for the folder.
4
If you were using the hotadd transport mode, remove any disks of the target virtual machine — the virtual machine mounted for a backup — that were hotadded to the NetVault Backup Client Virtual Machine — the virtual machine where the Plug‑in for VMware is running.
If the virtual machine is turned on, an error message — “Unable to access file <unspecified filename> since it is locked” — might display when you try to delete the snapshot, but the snapshot may thereafter disappear from the Snapshot Manager window. If a “Consolidate Helper-0” snapshot is displayed after you remove the snapshot, turn off the virtual machine.
After removing the snapshot BKB_SNAP, VMware recommends that you create and delete a snapshot. You can create and delete snapshots from the Snapshot Manager window in vSphere Client. The server tries to consolidate the redo logs during this operation, and therefore, it may take a few minutes to complete. Delete the Consolidate Helper snapshot, if it exists.

 

Restoring image-level backups

관련 문서

The document was helpful.

평가 결과 선택

I easily found the information I needed.

평가 결과 선택