サポートと今すぐチャット
サポートとのチャット

DR Series DR4300 - Owner's Manual

DR4300 system overview Technical specifications Initial system setup and configuration Pre-operating system management applications
Options to manage the pre-operating system applications System Setup Dell Lifecycle Controller Boot Manager PXE boot
Installing and removing system components
Safety instructions Before working inside your system After working inside your system Recommended tools Front bezel (optional) System cover Cooling shroud Cooling fans Cooling-fan assembly System memory Processors and heat sinks PCIe card holder Cable retention bracket Integrated storage controller card Expansion cards and expansion card riser Internal dual SD module (optional) Network daughter card Internal USB memory key (optional) System battery Power supply units (PSU) System board Trusted Platform Module Hard drives Hard drive backplane SD vFlash card (optional) Control panel assembly
Using system diagnostics Jumpers and connectors Troubleshooting your system

Expansion cards and expansion card riser

Expansion card installation guidelines
Removing an expansion card from expansion card riser 2 or 3
Installing an expansion card into the expansion card riser 2 or 3
Removing an expansion card from the expansion card riser 1
Installing an expansion card into the expansion card riser 1
Removing the riser 1 blank
Installing the riser 1 blank
Removing expansion card risers
Installing expansion card risers

An expansion card in the server is an add-on card that can be inserted into an expansion slot on the system board or riser card to add enhanced functionality to the system through the expansion bus.

* 
NOTE: A System Event Log (SEL) event is logged if an expansion card riser is unsupported or missing. It does not prevent your system from turning on and no BIOS POST message or F1/F2 pause is displayed.

Expansion card installation guidelines

Depending on your system configuration, the following PCI Express (PCIe) generation 3 expansion cards are supported:

Table 33. Supported expansion cards

Item 1 is the PCIe slot 1, on Riser 1 and is connected to Processor 2, it supports a low profile, half length 8x card. The slot width is 16x. Item 2 is the PCIe slot 2, on Riser 1 and is connected to Processor 2, it supports a low profile, half length 8x card. Item 3 is the PCIe slot 3, on Riser 1 and is connected to Processor 2, it supports a low profile, half length 8x card. The slot width is 16x. Item 4 is the PCIe slot 4, on Riser 2 and is connected to Processor 2, it supports a full height, full length 16x card. The slot width is 16x. Item 5 is the PCIe slot 5, on Riser 2 and is connected to Processor 1, it supports a full height, full length 8x card. The slot width is 16x. Item 6 is the PCIe slot 6, on Riser 3 and is connected to Processor 1, it supports a full height, full length 16x card. The slot width is 16x (alternate).

PCIe slot

Riser

Processor connection

Height

Length

Link width

Slot width

1

1

Processor 2

Low Profile

Half Length

x8

x16

2

1

Processor 2

Low Profile

Half Length

x8

x16

3

1

Processor 2

Low Profile

Half Length

x8

x16

4

2

Processor 2

Full Height

Full Length

x16

x16

5

2

Processor 1

Full Height

Full Length

x8

x16

6

3 (alternate)

Processor 1

Full Height

Full Length

x16

x16

* 
NOTE: To use PCIe slots 1 through 4 on the risers 1 and 2, both the processors must be installed.
* 
NOTE: The expansion card slots are not hot-swappable.

The following table provides guidelines for installing expansion cards to ensure proper cooling and mechanical fit. The expansion cards with the highest priority should be installed first using the slot priority indicated. All the other expansion cards should be installed in the card priority and slot priority order.

* 
NOTE: Ensure that the 100 G OPA x16 card is installed in slot 6 (x16 PCIe) on the alternate riser 3.

Removing an expansion card from expansion card riser 2 or 3

* 
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product.
* 
CAUTION: When removing the NV-RAM card ensure that, after powering down the system gracefully from the GUI or CLI, both green and amber LEDs on the card are off.
1.
Follow the safety guidelines listed in the Safety instructions section.
2.
Follow the procedure listed in the Before working inside your system section.
3.
When removing a card from riser 3, ensure that the PCIe holder latch is closed.
1.
Disconnect any cables connected to the expansion card.
2.
Lift the expansion card latch out of the guide slot.
3.
Hold the expansion card by its edges, and remove it from the expansion card connector.
4.
If you are removing the card permanently, install a metal filler bracket over the empty expansion slot opening and close the expansion card latch.
* 
NOTE: You must install a filler bracket over an empty expansion card slot to maintain Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system.
5.
Install the expansion card latch into the slot.
6.
Close the expansion card locking tabs.
Figure 32. Removing an expansion card from expansion card riser 2 or 3

This figure shows removing an expansion card from an expansion card riser 2 or 3.

a.
expansion card
b.
expansion card latch
c.
expansion card riser
d.
power connector (for GPU cards)
e.
expansion card connector
1.
Install an expansion card into the expansion card riser.
2.
Follow the procedure listed in the After working inside your system section.
Related tasks 
Before working inside your system
Installing an expansion card into the expansion card riser 2 or 3
After working inside your system
Related references 
Safety instructions

Installing an expansion card into the expansion card riser 2 or 3

1.
Follow the safety guidelines listed in the Safety instructions section.
2.
Follow the procedure listed in the Before working inside your system section.
* 
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product.
1.
Unpack the expansion card and prepare it for installation.
For instructions, see the documentation accompanying the card.
2.
Lift the expansion card latch and remove the filler bracket.
3.
Holding the card by its edges, position the card so that the connector on the expansion card aligns with the expansion card connector on the riser.
4.
Insert the card-edge connector firmly into the expansion card connector until the card is fully seated.
5.
Press the touch points to open the expansion card locking tabs.
6.
Close the expansion card latch.
7.
If applicable, connect the cables to the expansion card.
* 
NOTE: When installing a GPU card on riser 2 or riser 3 (default), connect the GPU card power cable to the power connector on the riser.
Figure 33. Installing an expansion card into the expansion card riser 2 or 3

This figure shows installing an expansion card into the expansion card riser 2 or 3

a.
expansion card
b.
expansion card latch
c.
expansion card riser
d.
power connector (for GPU cards)
e.
expansion card connector
1.
Follow the procedure listed in the After working inside your system section.
2.
Install any device drivers required for the card as described in the documentation for the card.
Related tasks 
Before working inside your system
After working inside your system
Related references 
Safety instructions
関連ドキュメント

The document was helpful.

評価を選択

I easily found the information I needed.

評価を選択