サポートと今すぐチャット
サポートとのチャット

DR Series Software 4.0 - Command Line Reference Guide

Introduction to the DR Series System Command Line Reference Guide Introducing the DR Series system Managing the DR Series system
Alerts Commands Authenticate Commands Network
Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --disable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help
OST RDA Stats Storage Group commands System
System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --support_agent --register system --support_agent --unregister system --support_agent --stats system --support_agent --status system --help
User Virtual Machine
Maintaining the DR Series System
Diagnostics Maintenance
Maintenance Command Usage maintenance --filesystem [--start_scan [verify_data | verify_rda_metadata | verify_metadata] [--storage_group <name>] maintenance --filesystem [--stop_scan] maintenance --filesystem [--scan_status] maintenance --filesystem [--scan_report [verbose]] maintenance --filesystem [--repair_status [verbose]] maintenance --filesystem [--repair_history [verbose]] maintenance --filesystem [--scan_restart [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--repair_now] maintenance --filesystem [--reclaim_space] maintenance --filesystem [--stop_reclaim_space] maintenance --filesystem [--clear_quarantine] maintenance --filesystem --show_throughput maintenance --configuration [--backup] maintenance --configuration [--restore] maintenance --configuration [--reinit_dictionary] maintenance --configuration [--reset_web_certificate] maintenance --hardware [--reinit_nvram] maintenance --hardware [--restore_hw_db] maintenance --hardware [--motherboard_replaced] maintenance --disk [--make_standby [slot num]] [--type <internal | external-<num> | service tag>] --clear_foreign] maintenance --remote_access [--show] maintenance --remote_access [--enable] maintenance --remote_access [--racreset] maintenance --remote_access [--static_ip] [--ip <IPv4/IPv6 address>] [--netmask <netmask>] [--gateway <IPv4/IPv6 address>] [--device <lom1|lom2|lom3|lom4>] maintenance --remote access [--disable] maintenance --vdisk --check_consistency --type <boot|internal|external> [--service_tag <service tag>] maintenance --help
Managing DR Series System Storage Operations
System Storage Operation Commands Connection Container VTL NDMP iSCSI FC Replication Seed Schedule
Data Integrity Checking Additional Linux Commands

fc --show [--verbose] [--target]

Syntax

fc --show --verbose 
fc --show --target

Result

For fc --show --verbose:

Target port: Slot 6 Port 0

    Port WWN: 50:00:65:b8:36:69:96:00
    Node WWN: 50:00:65:b8:36:69:90:00
    Symbolic node name: "Dell Inc.: Dell DR4300"
    Card description: QLogic QLE2662 Dual Port FC16 HBA
    Firmware version: 8.01.02
    Port state: Online
    Port type: NPort (fabric via point-to-point)
    Port speed: 16 Gbit

    Container: test2
            LUN: 1
                Type: Media changer (L700)
                Backing store path: /dev/sg76
            LUN: 2
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg36
            LUN: 3
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg37
            LUN: 4
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg38
            LUN: 5
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg39
            LUN: 6
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg40
            LUN: 7
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg41
            LUN: 8
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg42
            LUN: 9
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg43
            LUN: 10
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg44
            LUN: 11
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg45

            Initiators:
                21:00:00:24:ff:76:58:66


Target port: Slot 6 Port 1

    Port WWN: 50:00:65:b8:36:69:96:01
    Node WWN: 50:00:65:b8:36:69:90:00
    Symbolic node name: "Dell Inc.: Dell DR4300"
    Card description: QLogic QLE2662 Dual Port FC16 HBA
    Firmware version: 8.01.02
    Port state: Online
    Port type: NPort (fabric via point-to-point)
    Port speed: 16 Gbit

    Container: test2
            LUN: 1
                Type: Media changer (L700)
                Backing store path: /dev/sg76
            LUN: 2
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg36
            LUN: 3
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg37
            LUN: 4
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg38
            LUN: 5
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg39
            LUN: 6
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg40
            LUN: 7
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg41
            LUN: 8
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg42
            LUN: 9
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg43
            LUN: 10
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg44
            LUN: 11
                Type: Magnetic tape (ULT3580-TD4)
                Backing store path: /dev/sg45

            Initiators:
                21:00:00:24:ff:76:58:66

For fc --show --target:

Target port: Slot 6 Port 0

    Port WWN: 50:00:65:b6:33:63:14:88
    Node WWN: 50:00:65:b6:33:63:14:80
    Symbolic node name: "Dell Inc.: Dell DR4300"
    Card description: QLogic QLE2662 Dual Port FC16 HBA
    Firmware version: 8.01.02
    Port state: Online
    Port type: NPort (fabric via point-to-point)
    Port speed: 16 Gbit

Target port: Slot 6 Port 1

    Port WWN: 50:00:65:b6:33:63:14:89
    Node WWN: 50:00:65:b6:33:63:14:80
    Symbolic node name: "Dell Inc.: Dell DR4300"
    Card description: QLogic QLE2662 Dual Port FC16 HBA
    Firmware version: 8.01.02
    Port state: Online
    Port type: NPort (fabric via point-to-point)
    Port speed: 16 Gbit

fc --sessions [--topology] [--condensed]

Syntax

fc --sessions --topology

fc --sessions --condensed

Result

For fc --sessions --topology:
Target port: 50:00:65:b6:33:63:14:88
    Initiators connected:
        10:00:00:90:fa:a0:ae:0a
        50:0a:09:80:00:88:a7:71
        50:0a:09:80:06:8d:9a:40
        c0:03:ff:bd:1d:69:00:48

Target port: 50:00:65:b6:33:63:14:89
    Initiators connected:
        10:00:00:90:fa:cf:49:5e
        c0:03:ff:bd:1d:69:00:54
        c0:03:ff:bd:1d:69:00:58
        c0:03:ff:bd:1d:69:00:60
For fc --sessions --condensed:
Initiators connected.
      10:00:00:90:fa:a0:ae:0a
      50:0a:09:80:00:88:a7:71
      50:0a:09:80:06:8d:9a:40
      c0:03:ff:bd:1d:69:00:48
      10:00:00:90:fa:cf:49:5e
      c0:03:ff:bd:1d:69:00:54
      c0:03:ff:bd:1d:69:00:58
      c0:03:ff:bd:1d:69:00:60

fc --help <command>

Syntax

fc --help

Result

Usage:   
        fc --show [--verbose]  
             [--target]  
              
        fc --sessions [--topology]  
             [--condensed]  
              
        fc --help  
      
       fc <command> <command-arguments>  
       command can be one of:   
            --show       Displays command specific information.  
            --sessions   Show FC sessions  
      
    For command-specific help, please type fc --help <command>
			eg:  
            fc --help show  

Replication

関連ドキュメント

The document was helpful.

評価を選択

I easily found the information I needed.

評価を選択