予定されていた保守を実行中のため、サポートサイトでのフォームの送信が一時的に利用できません。 すぐにサポートが必要な場合は、テクニカルサポートまでお問い合わせください。 ご不便をおかけして申し訳ありません。
オンラインヘルプの参照
登録の完了
サインイン
価格設定をリクエスト
営業担当に連絡
製品バンドルが選択されました。 リクエストにより良く対応できるように、個別の製品を選択していただけますか? *
現在、テクニカル・サポート・エンジニアはお客様のチャットに対応できません。 迅速にサービスを受けられるよう、サービス・リクエスト・フォームを使用して
お客様の説明に基づいて、以下の記事が問題解決に役立つ可能性があります。
The following table provides a list of network ports used by NetVault.
80
TCP
HTTP Listen port for incoming Web Service connections.
135
RPC port used during the client push installation process.
3306
Port used to make a TCP/IP connection to the MySQL Server.
Configured on the NetVault Client on which the Plug-in for MySQL is installed.
The default port number is 3306. If a non-default port is configured for client connections on the MySQL Server, verify that the same port is configured on the NetVault Client.
To run multiple instances of MySQL on the same machine, a different port is configured for each instance.
5432
Listener port for PostgreSQL Database.
Configured on the NetVault Client on which the Plug-in for PostgreSQL is installed.
The default port number is 5432. If the PostgreSQL Database is configured to listen on a non-default port, verify that the same port is configured on the NetVault Client.
8443
HTTPS Listen port for incoming Web Service connections.
10000
Port for sending NDMP messages (NDMP control channels).
Configured on the NetVault Server on which the Plug-in for NDMP is installed.
The default port number is 10000. You can change it, if necessary.
20031
UDP
UDP messaging.
Required on server and clients.
Port used by Network Manager (nvnmgr).
User-defined listen ports for devices
Ports to listen on for device requests.
Configured on the NetVault Server and SmartClients.
Requirement: Two ports per drive.
User-defined connect ports for devices
Ports to connect to remote storage devices.
Configured on clients that connect to remote storage devices.
Requirement: Two ports per drive
User-defined listen ports for message channels
Ports to receive messages during data transfers.
Configured on NetVault Server and Clients.
Requirement: Three ports per client.
To run two or more plug-ins simultaneously on a client, NetVault requires two ports per plug‑in and an extra port per client. For example, to run two plug-ins simultaneously, NetVault requires (2 * 2) + 1 = 5 ports for a client.
User-defined connect ports for message channels
Ports for sending messages during data transfers.
User-defined connect ports for inter-machine setup
Ports for establishing initial contact (broadcast channels) while adding a NetVault Client, and later to ascertain its availability.
Requirement: Two ports per client.
User-defined listen ports for NDMP data channels
Ports to listen on for NetVault devices operating as NDMP movers.
These ports are used for data transfers between NDMP filer and storage device. These ports are required on the NetVault Server or Client to which the device is attached.
49152 through 65535
Dynamic ports that are used during the client push installation process.
This section describes some common errors and their solutions. It includes the following topics:
Quest *product*のオンラインサポートヘルプは、関連会社のサポートサイトで参照できます。「Continue(続行)」をクリックすると、*product*の適切なサポートコンテンツとアシスタンスへ移動します。
The document was helpful.
評価を選択
I easily found the information I needed.
© ALL RIGHTS RESERVED. 利用規約 プライバシー Cookie Preference Center
Quest Softwareポータルでは、IE8、9、10のサポートを終了しました。ブラウザを最新バージョンのInternet ExplorerまたはChromeにアップグレードすることをお勧めします。
IE 11へのアップグレード: ここをクリック
Chromeへのアップグレード: ここをクリック
の優れたセルフサービス機能を最大限に活用していただけるよう、IE8、9、10以外のブラウザをぜひご利用ください。