Chatta subito con l'assistenza
Chat con il supporto

NetVault Plug-in for DB2 3.3 - User Guide

Setting the Dropped Table Recovery option

To recover a dropped table, the Dropped Table Recovery option must be set to “Y” for the tablespace that contained the dropped table. For tablespaces created using the DB2 command prompt, this option is enabled by default. For tablespaces created using the DB2 Control Center graphical user interface (GUI), the Create Tablespace wizard lets you enable this option.

To verify the status of this option and to enable it if it has not been enabled, perform the following steps.

1
Start a terminal session on the DB2 Server, and navigate to the “…\SQLLIB\BIN” directory, where “…” indicates the installation path of DB2.
connect to <localDatabaseName>
alter tablespace <tablespaceName> dropped table recovery on

Recovery method 1: soft recovery

With a soft recovery, the data in other tables in the tablespace is rolled forward to the most current transaction log. This process prevents any current data that exists in other tables from being overwritten when the backup is restored.

To perform a soft recovery of a dropped database table, perform the following steps.

4
In the Navigation pane, click Create Restore Job, select Plug‑in for DB2 from the Plugin Type list, select a saveset that contains the backup of the target tablespace, and click Next.
5
Click Edit Plugin Options, and configure the following parameters on the Options tab:
Restore Mode: Select Online.
Rollforward Archived Logs: Clear this check box.
Verify that the Detailed Explanation column displays “Roll forward pending” status.
rollforward database <databaseName> to end of logs and complete tablespace
<tablespaceName> recover dropped table <backupID> to
"<completePathToRecoveryDirectory>"
create table <DDLstatementNotedEarlier>
import from "<recoveryDirectoryPath>\NODE0000\data" of del messages
<anyFileOutsideTargetDatabase> insert into <tableName>
select * from <tableName>
13
Repeat Step 7 through Step 12 for each table that you want to restore.

Recovery method 2: hard recovery

In a hard recovery, data in the tables of the target tablespace is rolled forward to the point at which the backup was taken. Changes to the tables within the target tablespace that occurred between the time the backup was taken and the time this recovery is performed, are lost. However, this procedure requires the least number of steps and time to perform.

To perform a hard recovery of a dropped database table, perform the following steps.

5
In the Navigation pane, click Create Restore Job, select Plug‑in for DB2 from the Plugin Type list, select a saveset that contains the backup of the target tablespace, and click Next.
7
Click Edit Plugin Options, and configure the following parameters on the Options tab:
Rollforward Archived Logs: Select this check box.
Hard Recovery: Select this option.
select * from <tableName>

Troubleshooting

This topic describes some common errors and their solutions. In cases where an error occurs and is not described in this table, obtain the DB2 error number from the NetVault Backup Logs, and then see the relevant DB2 documentation for help.

NetVault Backup 10.x service (netvault-pgsql) does not start on Windows.

Check the Windows Event Viewer for the following message: PDT FATAL: lock file “postmaster.pid” already exists.

NetVault Backup 10.x uses a PostgreSQL database. If the PostgreSQL database does not start, NetVault Backup cannot start. To correct this issue, delete the “postmaster.pid” file from the location referenced in the log and restart the NetVault Backup Server. For more information, see https://support.questcom/netvault-backup/kb/122475.

Backup fails to run

The database is in use. Offline backup is not allowed.

No other application or user should connect to the database.

Backup fails to run

Online backup is not allowed.

The “userexit” or “logretain” database configuration parameter is not enabled.

Backup error

Unable to Get Contact Addresses for “host_name” when running a remote backup.

The Plug‑in for DB2 Client cannot obtain a connection with the NetVault Backup Server. Add the IP address and the host information of the NetVault Backup Server to the “…\etc\hosts” file.

Backup Completed with warnings

Check the NetVault Backup Logs for the job to see if they display one or both of the following messages:

These messages indicate that the selected data was backed up, but the job’s index information was not properly added to NetVault Database. Without this index information, the data cannot be properly restored.

Method 1:

Open the Manage Devices page, select the backup media, and click Scan. NetVault Backup stores index information for backup jobs in the NetVault Database and the backup media. When you scan the backup media, the index information is added to the NetVault Database. To verify that the information was added, open the Manage Job Definitions page, and locate the specific job. If you can run the job now, the scan process has corrected the problem.

Method 2:

If the scan has failed, run the backup job again.

Cannot browse a database in the selection tree

SQL0332N Character conversion from the source code page “<codePageNumber>” to the target code page “<codePageNumber>” is not supported. SQLSTATE=57017

When you install NetVault Backup, the system is set in locale US, codeset=ISO8859-1, LANG=C. NetVault Backup uses a constant code page 819.

A DB2 database is created using code-set IBM-eucJP Database, code page 954.

Result: The system cannot translate between 819 and 954 as they are not compatible. This issue results in the error message “SQL0332N Character conversion from the source code page “819” to the target code page “UNKNOWN” is not supported. SQLSTATE=57017”

While installing a non-English version of NetVault Backup, verify that your system is running the correct to prevent any problems related to localization.

Restore job fails

DB2 Server error message 'SQL2043N Unable to start a child process or thread

Unable to start the child processes or threads required during the processing of a database task. There may not be enough available memory or system resources to create the process or thread. Close applications that are not being used or increase your system resources. Update your DB2 version to the latest IBM DB2 fix pack available for such version. Ensure that the system limit for number of processes or threads has not been reached by increasing the limit or by reducing the number of processes or threads already running. Ensure that there is enough virtual memory for new process and threads. Resubmit the restore job.

Relocating Tablespaces completes with warnings for automatic storage tablespaces

The SET TABLESPACE CONTAINERS command is not allowed on an automatic storage tablespace.

Containers associated with automatic storage tablespaces are under the control of the database. In DB2 version 9, the CREATE DATABASE command creates automatic storage enabled databases by default. However the user is allowed to create tablespaces with or without automatic storage enabled.

Related Documents

The document was helpful.

Seleziona valutazione

I easily found the information I needed.

Seleziona valutazione